Commit Graph

48623 Commits

Author SHA1 Message Date
Adrian Schmutzler
ef765ceb09 ath79/mikrotik: add function for loading ath9k caldata
The commands to read ath9k caldata on mikrotik subtarget are
mostly repetitive, so let's put them into a function to make
writing and reading them easier.

This function will only be required when patching the MAC address.
For cases where it is put correctly into the calibration data by
the vendor, caldata_sysfsload_from_file can be used directly as
done for ath10k at the moment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
John Thomson
74438d5419 ramips: add support for MikroTik RouterBOARD 760iGS (hEX S)
This patch adds support for the MikroTik RouterBOARD 760iGS router.
It is similar to the already supported RouterBOARD 750Gr3.
The 760iGS device features an added SFP cage, and passive
PoE out on port 5 compared to the RB750Gr3.

https://mikrotik.com/product/hex_s

Specifications:

- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB
- RAM:  256 MB
- Ethernet: 5x 10/100/1000 Mbps
- SFP cage
- USB port
- microSD slot

Unsupported:

- Beeper (requires PWM driver)
- ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1)
  The linux driver requires an interrupt, and pendown GPIO
  These are unknown, and not needed with the touchscreen
  only used for temperature and voltage monitoring.
  ads7846 hwmon:
  temp0 is degrees Celsius
  temp1 is voltage * 32

GPIOs:

- 07:  input passive PoE out (lan5) compatible (Mikrotik) device connected
- 17:  output passive PoE out (lan5) switch

Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common

To boot to intramfs image in RAM:

1. Setup TFTP server to serve intramfs image.
2. Plug Ethernet cable into WAN port.
3. Unplug power, hold reset button and plug power in.
   Wait (~25 seconds) for beep and then release reset button.
   The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT.
4. Wait for a minute. Router should be running OpenWrt,
   check by plugging in to port 2-5 and going to 192.168.1.1.

To install OpenWrt to flash:

1. Follow steps above to boot intramfs image in RAM.
2. Flash the sysupgrade.bin image with web interface or sysupgrade.
3. Once the router reboots you will be running OpenWrt from flash.

OEM firmware differences:

- RouterOS assigns a different MAC address for each port
- The first address (E01 on the sticker) is used for wan (ether1 in OEM).
- The next address is used for lan2.
- The last address (E06 on the sticker) is used for sfp.

[Initial port work, shared dtsi]
Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com>
[SFP support and GPIO identification]
Signed-off-by: Luka Logar <luka.logar@iname.com>
[Misc. fixes and submission]
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[rebase, drop uart3 from state_default on 750gr3, minor commit
title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
Adrian Schmutzler
ddf3e5c22d ramips/mt7621: create common DTSI for Mikrotik devices
This moves some common definitions for Mikrotik devices, mainly
routerboot partitions and reset key, to a common DTSI file.

While at it, remove unused hard_config DT label.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
Daniel Golle
ab4c6f1632 musl-fts: import from packages feed
libselinux requires musl-fts to build with musl. Import it from
packages feed as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-13 11:44:05 +01:00
Daniel Golle
e16b84df15 pcre: import from packages feeds
libselinux require pcre, import to to core so it can build without
packages feeds.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-13 11:28:28 +01:00
Paul Spooren
962e73c1a4 procd: add selinux variant
This commit adds a `selinux` variant to `procd` allowing to load an
SELinux policy at boot.

Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-13 09:53:50 +01:00
Thomas Petazzoni
a0df664531 libselinux: add new package
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase, update to 3.1]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
2020-08-13 09:31:34 +01:00
Thomas Petazzoni
6531eee347 libsepol: add new package
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase, update to 3.1]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
2020-08-13 09:31:34 +01:00
John Thomson
2d9db93397 ramips: use gpio-export for Mikrotik RouterBOARD 750Gr3 beeper
This beeper hardware requires a PWM driver for frequency selection.
Since the GPIO driver does not provide that, revert the beeper
support to a simple gpio-export.

This effectively reverts the corresponding changes from
6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 02:12:12 +02:00
Ansuel Smith
87e92d50e5 kernel: usb: move phy-qcom-ipq806x-usb to ipq806x modules.mk
This driver is only used by ipq806x SoCs. Move it there and drop
dependency from ipq40xx since it's not used anywere.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase on changes to previous patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Ansuel Smith
35d1f05094 ipq806x: replace nvmem qcom patch with upstream version
- Replace nvmem qcom patch with upstream version
- Update compatible

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches, minor commit message rewording]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Ansuel Smith
0c45ad41e1 ipq806x: replace phy dwc3 patch with upstream version
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Rui Salvaterra
e5eeb34a8c dropbear: fix ssh alternative when dbclient isn't built
The ssh symlink was still being created even when dbclient was disabled in the
build configuration. Fix this annoyance.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2020-08-12 21:57:37 +02:00
Adrian Schmutzler
6e7f40dff3 ath79: routerboard-92x: ensure explicit bios size in DTSI
The missing "size" property was acceptable in the context of a single
DTS as the underlying device is known to have a 64KB flash, and thus
the bios partition fit exactly between the preceding and following ones.

However as this block has moved in a DTSI, for the sake of clarity and
explicitness the size property is added to ensure that if the flash
happens to be larger than expected, the bios partition remains properly
sized.

Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 16:49:34 +02:00
Adrian Schmutzler
5dc74ad7f3 ath79: harmonize appearance of ethX nodes in qca953x DTSes
This harmonizes the appearance of ethX nodes in qca953x DTSes by:
- having the same order of nodes and properties
- removing redundant status property on eth1 (set in qca953x.dtsi)

This is meant to help both copy-pasters and reviewers, since
deviations and errors can be spotted easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:44:07 +02:00
Adrian Schmutzler
92b4f16bab kernel: add CGROUPS and IOSCHED_BFQ back to config
After those symbols have been removed from generic kernel config,
they were added to the target config during every kernel config
refresh. As that's not desirable, add them back to the generic
config.

Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Fixes: cfe235c436 ("kernel: modules: add package kmod-iosched-bfq")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Adrian Schmutzler
751486b31f build: fix README.md reference after rename
The README file is displayed on "make help", but updating the
command has been overlooked during the README -> README.md
rename.

Fix it.

Fixes: d0113711a3 ("README: port to 21st century")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Roger Pueyo Centelles
151e43df7a ath79: add support for MikroTik SXT 5nD r2 (SXT Lite5)
The MikroTik SXT Lite5 (product code RBSXT5nDr2, also SXT 5nD r2) is
an outdoor 5GHz CPE with a 16 dBi integrated antenna built around the
Atheros AR9344 SoC. It is based on the "sxt5n" board platform.

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64 MB
 - Storage: 128 MB NAND
 - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
    8-32 Vdc PoE in
 - 6 user-controllable LEDs:
  · 1x power (blue)
  · 1x wlan (green)
  · 4x rssi (green)
 - 1 GPIO-controlled buzzer

 See https://mikrotik.com/product/RBSXT5nDr2 for more details.

Notes:
 The device was already supported in the ar71xx target. There, the
 Ethernet port was handled by GMAC1. Here in ath79 it is handled by
 GMAC0, which allows to get link information (loss, speed, duplex) on
 the eth0 interface.

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Acknowledgments:
 Michael Pratt (@mpratt14) for helping on the network settings.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, use mikrotik LED label prefix, make names consistent,
add reg for bootloader2, use led_user for boot indication etc.,
minor cosmetic changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Sven Roederer
b2e1f7101d ath79: add support for MikroTik RouterBOARD 921GS-5HPacD-15s
The MikroTik RouterBOARD 921GS-5HPacD-15s (mANTBox 15s) is an outdoor
antenna for 5 GHz with an built-in router. This ports the board from
ar71xx.

See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9558 (720 MHz)
 - RAM: 128 MB
 - Storage: 128 MB NAND
 - Wireless: external QCA9892 802.11a/ac 2x2:2
 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
 - SFP: 1x host

Working:
 - NAND storage detection
 - Ethernet
 - Wireless
 - 1x user LED (blinks during boot, sysupgrade)
 - Reset button
 - Sysupgrade

Untested:
 - SFP cage (probably not working)

Installation (untested):
 - Boot initramfs image via TFTP and then flash sysupgrade image

As the embedded RB921-pcb is a stripped down version of the RB922 this patch
adds a common dtsi for this series and includes this to the final dts-files.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[move ath10k-leds closer to ath10k definition in DTS files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Roger Pueyo Centelles
7a705c067f ath79: add support for MikroTik RouterBOARD LHG 2nD
The MikroTik RouterBOARD LHG 2nD (sold as LHG 2) is a 2.4 GHz
802.11b/g/n outdoor device with a feed and an integrated dual
polarization grid dish antenna based on the LHG-HB platform.

See https://mikrotik.com/product/lhg_2 for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9533
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 18 dBi antenna
 - Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 12-28 Vdc PoE in
 - 8 user-controllable LEDs:
   · 1x power (blue)
   · 1x user (green)
   · 1x lan (green)
   · 1x wlan (green)
   · 4x rssi (green)

Note:
 The rssihigh LED is disabled, as it shares GPIO 16 with the reset
 button.

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, remove rssiled setup, adjust commit message, add DTSIs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Felix Fietkau
ed19ba04e8 mediatek: disable btif in device tree to make the WMAC work again
btif and wmac access the same resources and at the moment enabling one
breaks the other

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-12 13:02:13 +02:00
Felix Fietkau
74a66c0204 mediatek: fix PCI device tree node for elecom wrc-2533gent
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-12 13:02:13 +02:00
Felix Fietkau
37615174f5 mt76: update to the latest version
8d9a62e4def7 mt76: mt7915: fix crash on tx rate report for invalid stations
825343467df4 mt76: fix double DMA unmap of the first buffer on 7615/7915
99804560372b mt76: mt7615: register ext_phy if DBDC is detected
93407be934b2 mt76: mt7615: move drv_own/fw_own in mt7615_mcu_ops
e7774de844e8 mt76: mt7663s: move drv_own/fw_own in mt7615_mcu_ops
a5602514ab03 mt76: mt7615: hold mt76 lock queueing wd in mt7615_queue_key_update
5c42061ce181 mt76: do not inject packets if MT76_STATE_PM is set
ae4757a0ae90 mt76: mt7615: reschedule runtime-pm receiving a tx interrupt
c4544d1e8a1a mt76: mt76s: fix oom in mt76s_tx_queue_skb_raw
dc73103874cc mt76: mt76s: move tx processing in a dedicated wq
c828c84cb134 mt76: mt7663s: move rx processing in txrx wq
2b34f2f6b0ef mt76: mt76s: move status processing in txrx wq
f957b050d848 mt76: mt76s: move tx/rx processing in 2 separate works
6fe964295bd9 mt76: mt76s: get rid of unused variable
43d6127d8851 mt76: mt7915: enable U-APSD on AP side
58774b605f1c mt76: set interrupt mask register to 0 before requesting irq
06f722d8046c mt76: mt7915: clean up and fix interrupt masking in the irq handler
2fbd6baac103 mt76: mt7615: only clear unmasked interrupts in irq tasklet
5ea8b6187da2 mt76: mt76x02: clean up and fix interrupt masking in the irq handler
f2e71f0c1b7e mt76: mt7615: do not do any work in napi poll after calling napi_complete_done()
1eb94624bb12 mt76: mt7915: do not do any work in napi poll after calling napi_complete_done()
5e0c587b9ac1 mt76: mt7915: clean up station stats polling and rate control update
9ab20dfbf7b1 mt76: mt7915: increase tx retry count
fa69dd96f9c0 mt76: mt7915: enable offloading of sequence number assignment
9816f9812adb mt76: move mt76_check_agg_ssn to driver tx_prepare calls
ad90170b0af9 mt76: mt7615: remove mtxq->agg_ssn assignment
335cd51be4c6 mt76: mt7915: simplify aggregation session check
21f7734cbb49 mt76: mt7915: add missing flags in WMM parameter settings
21182f90d947 mt76: mt7915: add Tx A-MSDU offloading support
27670514328f mt76: mt7615: use v1 MCU API on MT7615 to fix issues with adding/removing stations

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-12 12:31:00 +02:00
Michael Yartys
91aab77bf1 ath10k-ct-firmware: update firmware images
Not a large change from last time, but should fix at least one rare wave-2
crash. The htt-mgt-community builds are trimmed for supporting lots of
stations (typically 150+ stations per radio).

Tested on Netgear R7800.

Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-12 11:50:48 +02:00
Adrian Schmutzler
7de3daa997 treewide: bump PKG_RELEASE after replacing which
Bump PKG_RELEASE for the affected packages as replacing "which" by
"command -v" represents a content change.

Fixes: 1fdf6b745c ("treewide: replace `which` with `command -v`")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:17:22 +02:00
Paul Spooren
1fdf6b745c treewide: replace which with command -v
Fix shellcheck SC2230
> which is non-standard. Use builtin 'command -v' instead.

Using `command -v` is POSIX compliant while `which` is not.  Also to
mention, `command -v` is a shell builtin whereas `which` is a separate
busybox applet.

Once applied to everything concerning OpenWrt we can disable the busybox
feature `which` and save 3.8kB.

Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also replace cases in zram-swap]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
Magnus Kroken
4165232c45 busybox: delete redundant patch
This problem has been fixed in upstream commit
6b6a3d9339f1c08efaa18a7fb7357e20b48bdc95. This patch now (harmlessly)
adds the same definition a second time.

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
Adrian Schmutzler
d0cb71a896 bcm47xx: use vendor_model scheme for device/image names
Most targets have been updated to consistently use the vendor_model
scheme for device definitions and thus, image names.

Apply this to bcm47xx as well. This does _not_ apply any other
specific naming changes.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
Adrian Schmutzler
683bcbdce1 bcm53xx: use vendor_model scheme for device/image names
Most targets have been updated to consistently use the vendor_model
scheme for device definitions and thus, image names.

Apply this to bcm53xx as well. This does _not_ apply any other
specific naming changes.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
David Woodhouse
0002d177e4 uboot-mediatek: resync patches with upstream
Now that my patches have been merged into upstream U-Boot, resync the
cosmetic changes and the commit IDs from the final commits.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-08-12 11:08:05 +02:00
Rosen Penev
b59a98b009 libjson-c: fix pkgconfig file
The pkgconfig file references the host directories, not the openwrt
ones. Used SED to fix as is done elsewhere. Removed CMAKE_INSTALL as a
result.

Removed now pointless CFLAGS.

Added PKG_BUILD_PARALLEL for faster compilation.

Various rearrangements for consistency between packages.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-08-11 21:29:44 +02:00
Hans Dedecker
5e512cc9c1 ppp: update to latest git HEAD
677aa53 Fix -W option for pppoe-discovery utility (#157)
115c419 Accept Malformed Windows Success Message (#156)
5bdb148 pppd: Add documentation of stop-bits option to pppd man page (#154)
2a7981f Add ipv6cp-accept-remote option
0678d3b pppd: Fix the default value for ipv6cp-accept-local to false

Refresh patches

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-08-11 21:27:07 +02:00
Hauke Mehrtens
c43af7a6cb kernel: Fix cake patch for kernel 4.19.138
This fixes the following build problem with cake:
net/sched/act_ctinfo.c: In function 'tcf_ctinfo_act':
net/sched/act_ctinfo.c:99:6: error: implicit declaration of function 'tc_skb_protocol'; did you mean 'skb_protocol'? [-Werror=implicit-function-declaration]
  if (tc_skb_protocol(skb) == htons(ETH_P_IP)) {
      ^~~~~~~~~~~~~~~
      skb_protocol
  CC [M]  net/sched/sch_hfsc.o

Fixes: fdac05b741 ("kernel: Update kernel 4.19 to version 4.19.138")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-11 21:11:53 +02:00
Hauke Mehrtens
2e8785d68c kernel: Create UBIFS v5 volume
In commit 87b35c16ad ("kernel: ubifs: create use file system format 4
by default") we changed the default UBIFS version used when the kernel
creates a new volume from 5 to 4. UBIFS v5 was added in kernel 4.10 and
only kernel 4.10 and later can read it.
We changed the kernel to create version 4 volumes also on more recent
kernel versions to make it possible to downgrade to an OpenWrt version
with kernel 4.9, the upgrade still works. This is probably not needed
any more and we can remove this patch.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-11 21:11:53 +02:00
Álvaro Fernández Rojas
a5a0b3f1d0 bcm63xx: switch to upstream CFE detection patch
This patch has been merged in linux 5.9.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-11 08:04:40 +02:00
Tony Ambardar
da4651833c malta: disable unnecessary built-in CDROM support
The CDROM is not needed for booting and can be included by selecting the
loadable module as a package instead.

This also avoids triggering a memory allocation failure during probing of
the CDROM due to lack of low 16MB DMA memory, as decribed in FS#3278:
https://bugs.openwrt.org/index.php?do=details&task_id=3278

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/3289
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-08-11 11:25:42 +08:00
Daniel Golle
5793112f75 oxnas: reduce size of ATA DMA descriptor space
After years of trying to find the reason for random kernel crashes
while both CPU and SATA are under load it has been found.
Some odd commented-out #defines in kref's single-port driver [1] which
were copied from the vendor driver made me develop a theory:
The IO-mapped memory area for DMA descriptors apparetly got some holes
just before the alignment boundaries.
This feels like an off-by-one bug in the hardware or maybe those fields
are used internally by the SATA controller's firmware.
Whatever the cause is: they cannot be used and trying to use them
results in reading back unexpected stuff and ends up with oopsing
Unable to handle kernel paging request at virtual address d085c004

Work around the issue by reducing the area used for bmdma descriptors.
This reduces SATA performance (iops) quite a bit, but finally makes
things work reliably. Possibly one could optimize this much more by
really just skipping the holes in that memory area -- however, that
seems to be non-trivial with the driver and libata in it's current form
(suggestions are welcome).
The 'proper' way to have good SATA performance would be to make use of
the hardware RAID features (one can use the JBOD mode to access even
just a single disc transparently through the RAID controller integrated
in the SATA host instead of accessing the SATA ports 'raw' as we do
now).

[1]: https://github.com/kref/linux-oxnas/blob/master/drivers/ata/sata_oxnas.c#L25

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-11 00:16:04 +01:00
Christoph Krapp
0af656e978 ar71xx: fix ZyXEL NBG6616 wifi switch
The device uses a rf-kill switch instead of a button. Furthermore the
GPIO is active high.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2020-08-11 01:12:22 +02:00
Tony Ambardar
d79a622217 toolchain/binutils: fix broken build of binutils 2.34 on mips64
Commit 53470bdf32 ("toolchain/binutils: Add binutils 2.34") logs refreshed
patches, but also adds a typo causing failed builds on mipsel64 platforms,
including the malta subtarget. Update the patch to fix this.

This fixes the following build error:
make[7]: *** No rule to make target 'elf64ltsmip.o', needed by 'ld-new'.  Stop.

Fixes: FS#3276
Fixes: 53470bdf32 ("toolchain/binutils: Add binutils 2.34")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2020-08-10 23:58:58 +02:00
Hauke Mehrtens
b35c54227b kernel: Move CONFIG_IONIC to generic kernel config
It is deactivated everywhere, just set this in the generic config.

Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 23:58:58 +02:00
Hauke Mehrtens
eafdd1a0fc malta: Refresh kernel configuration
This refreshes the kernel configuration on top of kernel 5.4.
It now builds without asking to select some kernel options on all 4
subtargets.
It still does not boot up, there is a different problem.

Tested-By: Yousong Zhou <yszhou4tech@gmail.com>
Acked-By: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 23:58:58 +02:00
Hauke Mehrtens
0a864f20fb bintuils: Pack libctf-nobfd.so in addition
readelf is linked against this library on MIPS64BE
This fixes a build problem on MIPS64BE.

In addition also explicitly activate it in the configure command.

Fixes: 60f595daab ("binutils: update to version 2.34")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 23:02:37 +02:00
Hauke Mehrtens
2f3d7abccd kernel: Update kernel 4.14 to version 4.14.193
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 19:34:37 +02:00
Hauke Mehrtens
fdac05b741 kernel: Update kernel 4.19 to version 4.19.138
Compile and run tested on lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 19:34:37 +02:00
Hauke Mehrtens
fce0f1501b mac80211: Update to version 5.8
The removed patches were applied upstream.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 19:34:37 +02:00
Christoph Krapp
d32010d5ff uboot-envtools: ath79: add ZyXEL NBG6616 uboot env support
This adds support for ZyXEL NBG6616 uboot-env access

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2020-08-10 18:37:47 +02:00
Christoph Krapp
459c8c9ef8 ath79: add support for ZyXEL NBG6616
Specifications:

  SoC: Qualcomm Atheros QCA9557
  RAM: 128 MB (Nanya NT5TU32M16EG-AC)
  Flash: 16 MB (Macronix MX25L12845EMI-10G)
  Ethernet: 5x 10/100/1000 (1x WAN, 4x LAN)
  Wireless: QCA9557 2.4GHz (nbg), QCA9882 5GHz (ac)
  USB: 2x USB 2.0 port
  Buttons: 1x Reset
  Switches: 1x Wifi
  LEDs: 11 (Pwr, WAN, 4x LAN, 2x Wifi, 2x USB, WPS)

MAC addresses:

WAN *:3f uboot-env ethaddr + 3
LAN *:3e uboot-env ethaddr + 2
2.4GHz *:3c uboot-env ethaddr
5GHz *:3d uboot-env ethaddr + 1

The label contains all four MAC addresses, however the one without
increment is first, so this one is taken for label MAC address.

Notes:

The Wifi is controlled by an on/off button, i.e. has to be implemented
by a switch (EV_SW). Despite, it appears that GPIO_ACTIVE_HIGH needs
to be used, just like recently fixed for the NBG6716.
Both parameters have been wrong at ar71xx.

Flash Instructions:

At first the U-Boot variables need to be changed in order to boot the
new combined image format. ZyXEL uses a split kernel + root setup and
the current kernel is too large to fit into the partition. As resizing
didnt do the trick, I've decided to use the prefered combined image
approach to be future-kernel-enlargement-proof (thanks to blocktrron for
the assistance).

First add a new variable called boot_openwrt:
setenv boot_openwrt bootm 0x9F120000

After that overwrite the bootcmd and save the environment:
setenv bootcmd run boot_openwrt
saveenv

After that you can flash the openwrt factory image via TFTP. The servers
IP has to be 192.168.1.33. Connect to one of the LAN ports and hold the
WPS Button while booting. After a few seconds the NBG6616 will look for
a image file called 'ras.bin' and flash it.

Return to vendor firmware is possible by resetting the bootcmd:
setenv bootcmd run boot_flash
saveenv
and flashing the vendor image via the TFTP method as described above.

Accessing the U-Boot Shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|    Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

| NBG6616> ?
| ATEN	x,(y)     set BootExtension Debug Flag (y=password)
| ATSE	x         show the seed of password generator
| ATSH	          dump manufacturer related data in ROM
| ATRT	(x,y,z,u) ATRT RAM read/write test (x=level, y=start addr, z=end addr, u=iterations
| ATGO	          boot up whole system
| ATUR	x         upgrade RAS image (filename)

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

| NBG6616> ATSE NBG6616
| 00C91D7EAC3C

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

| # bash ./tool.sh 00C91D7EAC3C
| ATEN 1,10FDFF5

Copy and paste the result into the shell to unlock zloader.

| NBG6616> ATEN 1,10FDFF5

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

| NBG6616> ATGU
| NBG6616#

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[move keys to DTSI, adjust usb_power DT label, remove kernel config
change, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 18:37:43 +02:00
Adrian Schmutzler
d4ac0ad543 treewide: make dependency on kmod-usb-net selective
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:54:30 +02:00
Nicholas Smith
c00b8dcf72 ath79: add support for Telco T1
Description:
    2x 100Mbps Etherent ports
    24V passive PoE
    64MB RAM
    16MB Flash
    2.4GHz WiFi
    1x WiFi antenna (RP-SMA connector)
    1x LTE antenna (SMA connector)
    Sierra Wireless MC7430 LTE modem

Flash instructions:
    Original firmware is based on OpenWrt.
    Flash using sysupgrade -n

SUPPORTED_DEVICES is added to support factory firmware.

Signed-off-by: Nicholas Smith <nicholas.smith@telcoantennas.com.au>
[add missing led_rssi0 DT label, add SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:49:29 +02:00
Aleksander Jan Bajkowski
37df722266 ath79: increase spi frequency on TL-WDR3500/3600/4300/4310
SPI Flash chip supports up to 33 MHz wihout fast read opcode.
Available frequencies are 112.5, 56.25, 37.5, 28.125, 22.5 etc.
This patch increases the nominal maximum frequency to 33 MHz,
reaching an effective increase from 22.5 to 28.125 MHz.

Formula to calculate SPI frequency:
Freq = 225 MHz / 2 / div

Before:

$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 3.58s
user	0m 0.00s
sys	0m 3.57s

After:

$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 2.95s
user	0m 0.00s
sys	0m 2.93s

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:43:37 +02:00