Openwrt build for Asrock G10 Router
Go to file
John Thomson 74438d5419 ramips: add support for MikroTik RouterBOARD 760iGS (hEX S)
This patch adds support for the MikroTik RouterBOARD 760iGS router.
It is similar to the already supported RouterBOARD 750Gr3.
The 760iGS device features an added SFP cage, and passive
PoE out on port 5 compared to the RB750Gr3.

https://mikrotik.com/product/hex_s

Specifications:

- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB
- RAM:  256 MB
- Ethernet: 5x 10/100/1000 Mbps
- SFP cage
- USB port
- microSD slot

Unsupported:

- Beeper (requires PWM driver)
- ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1)
  The linux driver requires an interrupt, and pendown GPIO
  These are unknown, and not needed with the touchscreen
  only used for temperature and voltage monitoring.
  ads7846 hwmon:
  temp0 is degrees Celsius
  temp1 is voltage * 32

GPIOs:

- 07:  input passive PoE out (lan5) compatible (Mikrotik) device connected
- 17:  output passive PoE out (lan5) switch

Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common

To boot to intramfs image in RAM:

1. Setup TFTP server to serve intramfs image.
2. Plug Ethernet cable into WAN port.
3. Unplug power, hold reset button and plug power in.
   Wait (~25 seconds) for beep and then release reset button.
   The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT.
4. Wait for a minute. Router should be running OpenWrt,
   check by plugging in to port 2-5 and going to 192.168.1.1.

To install OpenWrt to flash:

1. Follow steps above to boot intramfs image in RAM.
2. Flash the sysupgrade.bin image with web interface or sysupgrade.
3. Once the router reboots you will be running OpenWrt from flash.

OEM firmware differences:

- RouterOS assigns a different MAC address for each port
- The first address (E01 on the sticker) is used for wan (ether1 in OEM).
- The next address is used for lan2.
- The last address (E06 on the sticker) is used for sfp.

[Initial port work, shared dtsi]
Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com>
[SFP support and GPIO identification]
Signed-off-by: Luka Logar <luka.logar@iname.com>
[Misc. fixes and submission]
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[rebase, drop uart3 from state_default on 750gr3, minor commit
title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
.github build: Update README & github help 2018-07-08 09:41:53 +01:00
config kernel: further clean-up options and defaults 2020-08-10 09:54:14 +01:00
include build: fix README.md reference after rename 2020-08-12 14:03:17 +02:00
package musl-fts: import from packages feed 2020-08-13 11:44:05 +01:00
scripts treewide: replace which with command -v 2020-08-12 11:08:05 +02:00
target ramips: add support for MikroTik RouterBOARD 760iGS (hEX S) 2020-08-13 12:47:45 +02:00
toolchain toolchain/binutils: fix broken build of binutils 2.34 on mips64 2020-08-10 23:58:58 +02:00
tools ath79: add support for TP-Link TL-WPA8630P v2 2020-08-10 11:48:08 +02:00
.gitattributes
.gitignore build: improve ccache support 2020-07-11 15:19:53 +02:00
BSDmakefile
Config.in
feeds.conf.default feeds: add freifunk feed 2020-06-24 14:58:17 +02:00
LICENSE LICENSE: use updated GNU copy 2020-08-02 15:54:43 +02:00
logo.svg README: port to 21st century 2020-08-02 15:44:40 +02:00
Makefile build: improve ccache support 2020-07-11 15:19:53 +02:00
README.md README: port to 21st century 2020-08-02 15:44:40 +02:00
rules.mk tools: add fakeroot 2020-08-10 10:09:55 +02:00

OpenWrt logo

OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.

Sunshine!

Development

To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.

Requirements

You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.

gcc binutils bzip2 flex python3 perl make find grep diff unzip gawk getopt
subversion libz-dev libc-dev

Quickstart

  1. Run ./scripts/feeds update -a to obtain all the latest package definitions defined in feeds.conf / feeds.conf.default

  2. Run ./scripts/feeds install -a to install symlinks for all obtained packages into package/feeds/

  3. Run make menuconfig to select your preferred configuration for the toolchain, target system & firmware packages.

  4. Run make to build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.

The main repository uses multiple sub-repositories to manage packages of different categories. All packages are installed via the OpenWrt package manager called opkg. If you're looking to develop the web interface or port packages to OpenWrt, please find the fitting repository below.

Support Information

For a list of supported devices see the OpenWrt Hardware Database

Documentation

Support Community

  • Forum: For usage, projects, discussions and hardware advise.
  • Support Chat: Channel #openwrt on freenode.net.

Developer Community

License

OpenWrt is licensed under GPL-2.0