c9ac7b1729
This commit adds support for the D-Link DIR-505, previously supported in ar71xx. Hardware -------- SoC: Atheros AR9330 FLASH: 8M SPI-NOR RAM: 64M WIFI: 1T1R 1SS Atheros AR9330 LED: Power green, Status red BTN: WPS, Reset Installation ------------ Currently, installation is only possible by sysupgrading from an earlier OpenWrt version, U-Boot TFTP or a modded U-Boot. I do not have the original bootloader from D-Link on my device anymore, so i cannot test the factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
150 lines
2.3 KiB
Plaintext
150 lines
2.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9330.dtsi"
|
|
|
|
/ {
|
|
model = "D-Link DIR-505";
|
|
compatible = "dlink,dir-505", "qca,ar9330";
|
|
|
|
aliases {
|
|
serial0 = &uart;
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_status_red;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_status_red;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
wps {
|
|
label = "WPS button";
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&jtag_disable_pins>;
|
|
|
|
led_power_green: power {
|
|
label = "d-link:green:power";
|
|
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_status_red: status {
|
|
label = "d-link:red:status";
|
|
gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
|
|
led_enable {
|
|
gpio-hog;
|
|
output-low;
|
|
gpios = <1 GPIO_ACTIVE_LOW>;
|
|
line-name = "d-link:power:led";
|
|
};
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "host";
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-addr-swap = <0>;
|
|
switch-phy-swap = <0>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
compatible = "syscon", "simple-mfd";
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
num-chipselects = <1>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@10000 {
|
|
label = "art";
|
|
reg = <0x10000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
mac: partition@20000 {
|
|
label = "mac";
|
|
reg = <0x20000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "nvram";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "language";
|
|
reg = <0x40000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x80000 0x780000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
qca,no-eeprom;
|
|
};
|