Github releases usually don't contain the project name in the release
filename, which makes them very inconvenient to use from the build
system. Add support for naming the local file differently.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Force prereq again in SDK in order to fix GCC and Python dangling
symlinks:
staging_dir/host/bin/g++ -> /builder/ath79_generic/ccache_cxx.sh
staging_dir/host/bin/gcc -> /builder/ath79_generic/ccache_cc.sh
staging_dir/host/bin/python -> /usr/bin/python3.5
staging_dir/host/bin/python3 -> /usr/bin/python3.5
Ref: FS#2424
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Lan and Wan addresses are swapped compared to the original firmware.
This patch fixes this problem
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.
Therefore, the second VPE can be enabled for use with OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
The AVM FRITZ!Box 7412 buttons are both active low, which is currently
incorrectly defined in the device-tree.
This leads to the device booting directly into failsafe.
Signed-off-by: David Bauer <mail@david-bauer.net>
In commit d93969a13a ("ramips: Improve compatible for TP-Link
Archer devices") and subsequent ones, names of several devices
in ramips have been changed.
Since LED names are frequently invoked by $boardname, this has
broken LED setup in 01_leds, as $boardname and prefix in DTS
do not match anymore.
This patch updates device name prefixes for LEDs in DTS files,
and provides a migration script.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When adding support in 9ed272fe95 ("ath79: add support for
Comfast WR650AC v1/v2"), IMAGE_SIZE has not been added to device
definition.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ar71xx got lost during final rebase ..
Fixes: b417a0c48d ("ar71xx/ath79: ag71xx: init rings with GFP_KERNEL")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Upstream commit 246902bdf562d45ea3475fac64c93048a7a39f01
Which contains following explanation:
--
There is no need to use GFP_ATOMIC here, GFP_KERNEL should be enough.
The 'kcalloc()' just a few lines above, already uses GFP_KERNEL.
--
Looking at the code, all other descriptors also use plain GFP_KERNEL
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
When adding support in abbbecaa73 ("ath79: add support for
Comfast E314N-v2"), IMAGE_SIZE has not been added to device
definition.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We completely overlooked whitespace errors when reviewing
796ad2f7ef ("ath79: add support for D-Link DIR-842 C3").
Fix them and and also fix Makefile indent for C1/C2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is a dual band 11a/11n router with 1x wan and 4x gig lan ports.
There are two versions of this router which can be identified through
the factory web interface, v1 has 128mb ram and a uboot size of 128k,
v2 has 256mb ram and a uboot size of 256k, the remaining hardware and
PCB markings are the same.
Short specification:
SoC: Qualcomm Atheros QCA9558 - 720 MHz
Switch: Atheros AR8327
Second radio : Qualcomm Atheros QCA9880 802.11ac
4 LAN/1 WAN 1000Mps Ethernet
256 MB of RAM (DDR2)
16 MB of FLASH
3x2.4 GHz, 3x5GHz antennas
Steps to install :
Option A : Use vendor UI
Option B (if A is not working) :
(a) Download 'backup' from vendor UI and rename it backup.tar.gz
(b) Open the archive, and update the root password in /etc/shadow by
'$1$9wX3HGfB$X5Sb3kqzzBLdKRUR2kfFd0'
(c) 'Restore' from the archive using the vendor UI. Root password is now
'aaa'
(d) Scp the firwmware to the device:
$ scp <openwrt-sysupgrade>.bin root@192.168.1.1:/
(d) ssh to the device and flash the firmware:
$ cd /
$ mtd -e firmware -r write <openwrt-sysupgrade>.bin firmware
Signed-off-by: Gareth Parker <gareth41@orcon.net.nz>
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
Signed-off-by: Joan Moreau <jom@grosjo.net>
[reformatted commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Taken code from https://patchwork.ozlabs.org/patch/884850/ that was never
pushed by the author, and adapted to ath79.
The Comfast E314N-V2 is a 2.4 GHz 2x2 radio with a built-in directional
antenna and a second Ethernet port - very similar to the Ubiquiti
NanoStation M2. The Ethernet port features a pass-through PoE capability,
enabled or disabled with a slide switch.
Specifications :
- System-On-Chip: Qualcomm/Atheros QCA9531
- CPU/Speed: 650 MHz
- Flash size: 8 MiB
- RAM: 64 MiB
- 2 Ethernet 1Gbp
- 1 reset button
- 1 switch to choose PoE from LAN or Wan. 48Vdc
- Wifi 2.4 Ghz (b/g/n)
- UART inside the box (3.3V, pins marked on the PCB)
Firmware can be flashed on these units by the following method:
1.) Apply power to the unit
2.) Immediately AFTER applying power, hold down the reset button
3.) The WAN, LAN, and wireless lights will flash - wait three seconds
(three flashes) and then release the button.
4.) After a second, the lights will flutter quickly and the unit will be
visible at 192.168.1.1. A web page will be available to enable quick
and simple uploading and flashing of firmware.
During the boot process, these units also look for a tftp server at
192.168.1.10. If one is present, the firmware can be uploaded as a file
called firmware-auto.bin
Signed-off-by: Joan Moreau <jom@grosjo.net>
[wrapped commit message - fix commit title capitalization]
Signed-off-by: David Bauer <mail@david-bauer.net>
In the commit 623716dd43 ("comgt-ncm: Fix NCM protocol")
the dependencies to vendor NCM drivers were removed, because:
> comgt-ncm should not depend on the USB-serial-related kernel modules,
> as the cdc-wdm control device works without them. There is also no need
> to depend on kmod-huawei-cdc-ncm, since other manufacturers (like
> Ericsson and Samsung) which use other kernel modules should also be
> supported.
From a user-perspective this does not make sense, as installing comgt-ncm
(or luci-proto-ncm) should install all needed dependencies for using such
a device.
Furthermore depending on kmod-huawei-cdc-ncm does not mean that Ericsson
and Samsung devices can't be supported. By the way it seems that Ericsson
and Samsung devices never used NCM, but act as serial modems.
Thus this commit adds the dependencies again.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[fixed title capitalization, formatted commit message,
renamed Sony-Ericsson to Ericsson]
Signed-off-by: David Bauer <mail@david-bauer.net>
HiWiFi HC5761A is an "MT7628AN variant" of HC5761
Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7610EN 802.11ac 433Mbps
- 3x 10/100 Mbps Ethernet
Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot
Known bug:
- SD slot does not work (See PR 1500)
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
HC5661A:
- Fix pinctrl
- Fix image size (15808k)
- Use switch trigger for WAN LED
Both:
- Use tpt LED trigger for wireless
- Explicitly disable USB nodes
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
HiWiFi has several MT7628AN routers which have similar specs
Add HC5X61A.dtsi to include them, like HC5X61.dtsi (for MT7620A)
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Specifications:
- SoC: AR9341
- RAM: 64M
- Flash: 16M
- Ethernet: 1 * FE port
- WiFi: ar934x-wmac
- Sound: WM8918 DAC
1 * 3.5mm headphone jack
2 * RCA connectors for speakers
1 * SPDIF out
- USB: 1 * USB2.0 port
Flash instruction:
Upload generated factory image via vendor's web interface.
Notes:
A. Audio stuff:
1. Since AR934x, all pins for peripheral blocks can be mapped to
any available GPIOs. We currently don't have a PCM/I2S driver
for AR934x so pinmux for i2s and SPDIF are bound to i2c gpio
node. This should be moved into I2S node when a PCM/I2S driver
is available.
2. The i2c-gpio node is for WM8918. DT binding for it can't be added
currently due to a missing clock from I2S PLL.
B. Factory image:
Image contains a image header and a tar.gz archive.
1. Header: A 288 byte header that has nothing to do with appended
tarball. Format:
0x0-0x7 and 0x18-0x1F: magic values
0x20: Model number string
0xFC: Action string. It's either "update" or "backup"
0x11C: A 1 byte checksum. It's XOR result of 0x8-0x11B
Firmware doesn't care about the rest of the header as long as
checksum result is correct.
The same header is used for backup and update routines so the
magic values and model number can be obtained by generating a
backup bin and grab values from it.
2. Tarball: It contains two files named uImage and rootfs, which
will be flashed into corresponding mtd partition.
Writing a special utility that can only output a fixed binary
blob is overkill so factory image header is placed under
image/bin instead.
C. LED
The wifi led has "Wi-Fi" marked on the case but vendor's firmware
used it as system status indicator. I did the same in this device
support patch.
D. Firmware
Factory u-boot is built without 'savenv' support so it's impossible
to change kernel offset. A 2MB kernel partition won't be enough in
the future. OKLI loader is used here to migrate this problem:
1. add OKLI image magic support into uImage parser.
2. build an OKLI loader, compress it with lzma and add a normal
uImage header.
3. flash the loader to where the original kernel supposed to be.
4. create a uImage firmware using OKLI loader.
5. flash the created firmware to where rootfs supposed to be.
By doing so, u-boot will start OKLI loader, which will then load
the actual kernel at 0x20000.
The kernel partition is 2MB, which is too much for our loader.
To save this space, "mtd-concat" is used here:
1. create a 64K (1 erase block) partition for OKLI loader and
create another partition with the left space.
2. concatenate rootfs and this partition into a virtual flash.
3. use the virtual flash for firmware partition.
Currently OKLI loader is flashed with factory image only.
sysupgrade won't replace it. Since it only has one function
and it works for several years, its unlikely to have some bugs
that requires a replacement.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This adds support for uImage used by OpenWrt kernel loader.
The parser searches for uImage header at flash eraseblock boundary
and it might attempt to split any firmware with loader, therefore
this entry doesn't have MTD_PARSER_TYPE_FIRMWARE so that this parser
is only used when explicitly defined in dts.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Hardware spec of DIR-842 C3:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or
the u-boot failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted.
Otherwise the u-boot will enter failsafe mode as the checksum
of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the
firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
just upgrade the factory.bin through the u-boot failsafe interface
and then goto step 2.
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
According to detective grep, with this patch all devices should
be labelled "TP-Link" consistently.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This seems to be identical to CPE210 v1 despite having removable
antennas.
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with
two Ethernet ports based on Atheros AR9334
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 2T2R 5 GHz
- 13 dBi built-in antenna
- Power, LAN0, LAN1 green LEDs
- 4x green RSSI LEDs
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Based on the work of Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The loader-okli is shared by several TP-Link CPExxx devices, so
give it its own definition to prevent too much code duplication.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This puts some common code into a new shared DTSI. Common nodes
are chosen so that the new DTSI can be used for CPE210 v1, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is a preparation for ath79 support of the CPE210/CPE510 v1.
Kernel size is chosen equal to the latest update for CPE610 v1.
This also updates the partition size in ar71xx target, so code
remains consistent if someone looks up the device. Since CPE210,
CPE510, WBS210 and WBS510 (all v1) share the same partition
layout definition, and are on deprecated target anyway, this
changes them all at once.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since usign miscalculates SHA-512 digests for input sizes of exactly
64 + N * 128 + 110 or 64 + N * 128 + 111 bytes, we need to apply some
white space padding to avoid triggering the hashing edge case.
While usign itself has been fixed already, there is still many firmwares
in the wild which use broken usign versions to verify current package
indexes so we'll need to carry this workaround in the forseeable future.
Ref: https://forum.openwrt.org/t/signature-check-failed/41945
Ref: https://git.openwrt.org/5a52b379902471cef495687547c7b568142f66d2
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Introduce a new option CONFIG_SIGNATURE_CHECK which defaults to the value
of CONFIG_SIGNED_PACKAGES and thus is enabled by default.
This option is needed to support building target opkg with enabled
signature verification while having the signed package lists disabled.
Our buildbots currently disable package signing globally in the
buildroot and SDK to avoid the need to ship private signing keys to
the build workers and to prevent the triggering of random key generation
on the worker nodes since package signing happens off-line on the master
nodes.
As unintended side-effect, updated opkg packages will get built with
disabled signature verification, hence the need for a new override option.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This update fixes usign signature verification on files with certain
file sizes triggering a bug in the shipped SHA-512 implementation.
5a52b37 sha512: fix bad hardcoded constant in sha512_final()
3e6648b README: replace unicode character
716c3f2 README: add reference to OpenBSD signify
86d3668 README: provide reference for ed25519 algorithm
939ec35 usign: main.c: describe necessary arguments for -G
Ref: https://forum.openwrt.org/t/signature-check-failed/41945
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This parser's matching function appears to be too generic as it matches
e.g. Buffalo WZR-HP-G300NH. That results in incorrect parts parsing.
Luckily this parser is needed by Fon FON2601 only which uses DT-based
ramips target. It means we can depend on mtd subsystem matching of
"fonfxc,uimage" string.
That said triggering this parser based on the "firmware" (or whatever
MTD_SPLIT_FIRMWARE_NAME is) partiiton name is not needed. It can be
dropped which will automatically fix the Buffalo WZR-HP-G300NH case.
Fixes: a1c6a316d2 ("ramips: add support for Fon FON2601")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
