netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: MT7530BU
- UART:
- J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Specification:
- CPU: MTK MT7620A
- RAM: 64MB
- ROM: 16MB SPI Flash Macronix MX25L12835E
- WiFi1: MediaTek MT7620A
- WiFi2: MediaTek MT7612E
- Button: reset, wps
- LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN
- Ethernet: 5 ports, 4 LAN + 1 WAN
- Other: 1x UART 1x USB2.0
Installation:
Update using ASUS Firmware Restoration Tool:
1. Download the ASUS Firmware Restoration Tool but don't open it yet
2. Unplug your computer from the router
3. Put the router into Rescue Mode by: turning the power off, using a pin
to press and hold the reset button, then turning the router back on while
keeping the reset button pressed for ~5 secs until the power LED starts
flashing slowly (which indicates the router has entered Rescue Mode)
4. Important (if you don't do this next step the Asus Firmware
Restoration Tool will wrongly assume that the router is not in Rescue Mode
and will refuse to flash it): go to the Windows Control Panel and
temporarily disable ALL other network adapters except the one you will use
to connect your computer to the router
5. For the single adapter you left enabled, temporarily give it the
static IP 192.168.1.10 and the subnet mask 255.255.255.0
6. Connect a LAN cable between your computer (make sure to use the
Ethernet port of the adapter you've just set up) and port 1 of the router
(not the router's WAN port)
7. Rename sysupgrade.bin to factory.trx
8. Open the Asus Firmware Restoration Tool, locate factory.trx and click
upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)
9. Flashing and reboot is finished when the power LED stops blinking and
stays on
MAC assignment based on vendor firmware:
2g 0x4 label
5g 0x8004 label +4
lan 0x22 label +4
wan 0x28 label
Signed-off-by: Zhijun You <hujy652@gmail.com>
[rebased due to DTSI patch, minor commit message adjustments, fix
label MAC address (lan->wan), do spi frequency increase separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This creates a DTSI for the ASUS RT-AC51U and the upcoming RT-AC54U,
as they are quite similar.
White at it, drop the unneeded "status = okay" for ethernet.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops some ancient kernel version switches from patches on
lantiq target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops some ancient kernel version switches from patches on
bcm27xx target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.
Refresh remaining target patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the obsolete version switches for non-supported kernels
from local drivers in generic target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops kernel version switches for versions not supported by
OpenWrt master at the moment. This only adjusts local code, but
doesn't touch patches to existing external packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The property "ralink,port-map" has been obsolete long before
this device was added, and the device is a one-port anyway.
Just remove it.
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This tidies up the ethernet node in mt7620 DTS files by:
- removing unnecessary status as it is not disabled
- reordering properties consistently
- adding empty lines to enhance readability
This should make comparison and reviewing new PRs based on C/P easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
crypto_bignum_rand() use needless time-consuming filtering
which resulted in SAE no longer connecting within time limits.
Import fixes from hostap upstream to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
31e99fe3da which introduced this code was unfortunately untested.
This commit fixes a number of issues and works around the fact that in
this particular scheme, the LZO payload may be padded at the end which
will trigger a harmless lzo decompression error.
This commit also disambiguates the debug printks.
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 31e99fe3da ("generic: platform/mikrotik: support LZOR encoding")
This commit adds support for the Fritzbox 7360v2
CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A
DECT is not working.
Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.
Firmware can be flashed with this method:
1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:
passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin
5.) wait till red light flashing turns off.
6.) type: exit
Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.
Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
2e73848 jail: SIGSEGV must not be forwarded to the child process
7e150f6 jail: unnamed jails can not have netns (fix segfault)
1ab539b jail: add option to provide /dev/console to containers
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Increase SPI frequency to 33.333 MHz. It's maximum frequency supported
by SPI Flash memory chip without Fast read opcode.
Before:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real 0m 3.21s
user 0m 0.00s
sys 0m 3.21s
After:
$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real 0m 2.52s
user 0m 0.00s
sys 0m 2.52s
Tested on TP-Link TL-WR1043ND V2.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
The bcm6345-periph-intc driver only targets a single CPU at a time, even
if the notional affinity is wider. Let's inform the core code about this.
This patch gets rid of the kernel message:
"genirq: irq_chip bcm6345-periph-intc did not update eff. affinity mask
of irq 52"
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
In file included from ./arch/mips/include/asm/io.h:34,
from ./arch/mips/include/asm/mmiowb.h:5,
from ./include/linux/spinlock.h:60,
from ./include/linux/irq.h:14,
from drivers/irqchip/irq-bcm6345-ext.c:10:
drivers/irqchip/irq-bcm6345-ext.c: In function 'bcm6345_ext_intc_of_init':
./arch/mips/include/asm/mach-bcm63xx/ioremap.h:48:9: warning: 'base' may be used uninitialized in this function [-Wmaybe-uninitialized]
return is_bcm63xx_internal_registers((unsigned long)addr);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-bcm6345-ext.c:255:16: note: 'base' was declared here
void __iomem *base;
^~~~
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
drivers/irqchip/irq-bcm6345-periph.c: In function 'bcm6345_periph_irq_handle':
drivers/irqchip/irq-bcm6345-periph.c:55:21: warning: 'block' may be used uninitialized in this function [-Wmaybe-uninitialized]
struct intc_block *block;
^~~~~
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
1094741224 aarch64: Accept PLT calls to __getauxval within libc.so
a98b8b221c NEWS: Mention fixes for BZ 25810/25896/25902/25966
4c833bbebe x86-64: Use RDX_LP on __x86_shared_non_temporal_threshold [BZ #25966]
3b9ceb3320 NEWS: Mention bug 25639 fixed in 2.31 branch
bb44fe7711 oc_FR locale: Fix spelling of April (bug 25639)
f2ac792047 oc_FR locale: Fix spelling of Thursday (bug 25639)
18fdba553d Add a C wrapper for prctl [BZ #25896]
7c9e054afd powerpc: Rename argN to _argN in LOADARGS_N [BZ #25902]
9c5ae39a64 Add C wrappers for process_vm_readv/process_vm_writev [BZ #25810]
63c3696a4a Mark unsigned long arguments with U in more syscalls [BZ #25810]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This backports upstream fixes for the out of bounds write vulnerability in json-c.
It was reported and patches in this upstream PR: https://github.com/json-c/json-c/pull/592
Addresses CVE-2020-12762
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
Though generic diag.sh allows to use different LEDs to indicate different
states, this patch just moves the old assignment and does not try to
"improve" the assignment by using additional colors.
However, individual proposals to do so are welcome.
For the few cases where status_led2 was used in old diag.sh, only the
primary LED was migrated.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.
Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k. Since ath10k caldata is no longer pulled from
this implementation, this commit also disables the publication in sysfs
to avoid wasting memory.
Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Program received signal SIGSEGV, Segmentation fault.
main_autofs (argv=<optimized out>, argc=<optimized out>)
at fstools-2020-05-06-eec16e2f/block.c:1193
1193: if (!m->autofs && (mp = find_mount_point(pr->dev))) {
Fixes: c3a43753b9 ("fstools: update to the latest version")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
An e-mail response from MikroTik contained a minimal overview
on hardware option bits which mentioned a currently unknown bit.
While not being too detailed what it does, add it for documentation purposes.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: System (red / green / amber)
BTN: Reset
The USB port on the device is (in contrast to other Aruba boards) real
USB. The AP uses a CP2101 USB TTY converter on the board.
Console baudrate is 9600 8n1.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
Make sure you use the mtd partition with the label "ubi" here!
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
Hotplug scripts are sourced so the #!/bin/sh is superfluous/deceptive.
Re-arrange script to only source 'procd' if we get to the stage of
needing to signal the process, reduce hotplug processing load a little.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The BL-W1200 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612E)
- 5x 10/100/1000 Mbps Ethernet (MT7530)
- 2x external, non-detachable antennas (Wifi 2.4G/5G)
- 1x USB 2.0
- UART (R2) on PCB (57600 8n1)
- 9x LED (1 GPIO controlled), 1x button
- u-Boot bootloader
Known issues:
- No status LED. Used WPS LED during boot/failsafe/sysupgrade.
Installation:
1. Apply initramfs image via factory web-gui.
2. Install sysupgrade image.
How to revert to OEM firmware:
- sysupgrade -n -F stock_firmware.bin
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
