The UniFi AC LED mapping is currently off. The blue/white LED are used
as WiFi indicators, while the vendor firmware does not feature WiFI
LEDs.
Instead, the LEDs are used to indicate the devices status. Align the LED
mapping to match the vendor firmware as good as possible.
Signed-off-by: David Bauer <mail@david-bauer.net>
a88fb42 iwinfo: add device id for Qualcomm Atheros QCA9886
1b69d86 iwinfo: add device id for Qualcomm Atheros QCA9887
Signed-off-by: David Bauer <mail@david-bauer.net>
KERNEL_DEVPTS_MULTIPLE_INSTANCES and KERNEL_POSIX_MQUEUE were
previously enabled by default only if KERNEL_LXC_MISC was selected.
KERNEL_LXC_MISC was enabled only if the SMALL_FLASH (anti-)feature
was not selected.
Now that KERNEL_LXC_MISC no longer exists, make sure that those
options are also only enabled by default for !SMALL_FLASH targets.
Fixes: 4f94a331 ("config: kernel: remove KERNEL_LXC_MISC")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel features are neutral. The two cascaded features can also be
useful for other container related tools
It's also less error-prone if only kconfig symbols from the kernel are
prefixed KERNEL_
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This reverts commit 5b98061bb1.
As Piotr Dymacz pointed out:
In QCA MIPS based WiSOCs, for first USB interface,
device/host mode can be selected _only_ in hardware
see description of 57c641ba6e
QCA955x and QCA9563, second USB can be switched to device
mode in software (tested and confirmed on real hardware).
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Current ar724x code does the reset only on single pci bus, and
in case of qca9558 writes the wrong register (0x10 vs 0x0c).
This change allows the reset of second pci bus, commonly used in
Archer C7 devices, in case host controller is stuck in reset.
If the resetting controller on boot can solve any other issue it
can be enabled unconditionally by removing reset check before
ar724x_pci_hw_init is called.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
[refreshed to apply cleanly]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Enable flushing of write buffers on qca955x. GPL code has 0x88 reg
defined for PCI flush which is likely an error since the device
freezes on boot. So use DS default value 0xA8 for PCI flush.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
b8238df sysupgrade: support "backup" attribute
This update requires "sysupgrade" method callers to pass "backup"
attribute if $UPGRADE_BACKUP is used in the project.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This explicitly tells procd what backup file should be used during
sysupgrade (if any). It's much more generic this way compared to the
magic /tmp/sysupgrade.tgz file that had to be created before a call.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Make treat copy-kernel.o as intermediate and delete it when it's no
longer needed. This can fail when the same submake was triggered
multiple times for different devices.
arm-openwrt-linux-muslgnueabi-as -k -o copy-kernel.o copy-kernel.S
export MAKEFLAGS= ;make -w -C copy-kernel CROSS_COMPILE=arm-openwrt-linux-muslgnueabi-
arm-openwrt-linux-muslgnueabi-objcopy -O binary -S copy-kernel.o copy-kernel.bin
make[5]: Entering directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
arm-openwrt-linux-muslgnueabi-objcopy -O binary -S copy-kernel.o copy-kernel.bin
rm copy-kernel.o
make[5]: Leaving directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
# "App" partition is the rootfs
arm-openwrt-linux-muslgnueabi-objcopy: 'copy-kernel.o': No such file
Makefile:27: recipe for target 'copy-kernel.bin' failed
make[5]: Leaving directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
make[5]: *** [copy-kernel.bin] Error 1
Makefile:244: recipe for target '/builder/shared-workdir/build/build_dir/target-arm_fa526_musl_eabi/linux-gemini/tmp/openwrt-gemini-storlink_sl93512r-ext4-factory.bin' failed
make[4]: *** [/builder/shared-workdir/build/build_dir/target-arm_fa526_musl_eabi/linux-gemini/tmp/openwrt-gemini-storlink_sl93512r-ext4-factory.bin] Error 2
With this change, output files are directed to $(KDIR)
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The 2.4 GHz radio had very poor signal reception (-89 dBm for an AP
sitting 5 m away). By enabling the external amplifier, received signal
has improved to -50 dBm for the same AP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
5f0d2e0491 [AArch64] Add ifunc support for Ares
e6b7252040 aarch64,falkor: Use vector registers for memcpy
c74b884f70 aarch64,falkor: Ignore prefetcher tagging for smaller copies
0fc5934ebd aarch64/strncmp: Use lsr instead of mov+lsr
e0a0bd3acc aarch64/strncmp: Unbreak builds with old binutils
638caf3000 aarch64: Improve strncmp for mutually misaligned inputs
d5f45a29ff aarch64/strcmp: fix misaligned loop jump target
7f690fafad aarch64: Improve strcmp unaligned performance
40df047b3b aarch64: Fix branch target to loop16
062139f233 aarch64: Optimized memcmp for medium to large sizes
f3e2add213 aarch64: Use the L() macro for labels in memcmp
22bd3ab40e posix: Fix large mmap64 offset for mips64n32 (BZ#24699)
bdd16894aa aarch64: handle STO_AARCH64_VARIANT_PCS
0b48caab9a aarch64: add STO_AARCH64_VARIANT_PCS and DT_AARCH64_VARIANT_PCS
949da7f2fd io: Remove copy_file_range emulation [BZ #24744]
f056ac8363 libio: do not attempt to free wide buffers of legacy streams [BZ #24228]
5f90e009b1 NEWS: add entries for bugs 22964, 24180, and 24531
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This allows platform code to check if firmware image can be used with
preserving a backup. It may be used e.g. when installing vendor
firmwares that won't restore appended backup archive.
Suggested-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So far, MAC address setup for those devices has been using local
addresses although additional MAC addresses are available on flash.
On device, we found the following situation:
position Y1 Y1S
0x4 *:d4 *:e4
0x8004 *:d6 *:e8
0x28 *:d4 *:e4
0x2e *:d7 *:eb
Since 0x4 and 0x28 yield the same address, the former was set for
ðernet in DTS. However, the typical location on this
architecture is 0x28, so this patch changes that.
For further setup in 02_network, the local bit for lan_mac is
removed, so the address from ðernet is used at all. For wan_mac,
instead of calculating an address with local bit set, this patch
exploits the previously unused address in 0x2e.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch changes wan MAC address setup from retrieving it by
calculation to reading it from flash.
Changes are limited to cases where on-device check was possible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[fix mac for newifi-d1; drop adslr,g7 because it's unlikely for
vendor to specifically use 2.4g mac as wan_mac]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
In 555ca422d1 ("ramips: fix D-Link DIR-615 H1 switch port
mapping"), port setup for dir-615-h1 was changed without removing
the old one. This was working as the new one was triggered earlier
than the old one.
(In the meantine, changed sorting during ramips rename patches
actually inversed that order.)
Anyway, just remove the wrong case now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ARC FreeStation5 is present twice in MAC address setup.
From older commits/changes, it is not possible to reconstruct
the correct choice only by reading the annotations.
Thus, remove the second case and keep the first one, so behavior
stays the same (as nobody seems to have complained about it).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch removes unnecessary MAC address setup statements in
ramips' 02_network by doing several optimizations:
1. For the following devices, lan_mac was set up with
mtd_get_mac_binary although the same address was set in DTS.
The lan_mac statement is removed in 02_network, but
wan_mac is kept:
- mercury,mac1200r-v2
- phicomm,k2g
- skylab,skw92a
- wiznet,wizfi630a
2. For the following devices, wan_mac was set up with
mtd_get_mac_binary although the same address was set in DTS.
The wan_mac statement is removed in 02_network, no
lan_mac is present:
- buffalo,whr-g300n
- glinet,gl-mt300n-v2
- zyxel,keenetic-start
3. For the following device, lan_mac and wan_mac were set up
with mtd_get_mac_binary to the same address as set in DTS.
Both statements are removed in 02_network:
- buffalo,whr-600d
4. For some devices, it was possible to move setup from 02_network
to DTS by introducing previously missing mtd_mac_address:
- buffalo,whr-1166d
- buffalo,whr-300hp2
- buffalo,wsr-600dhp
- ohyeah,oy-0001
- planex,vr500
5. For one device, mtd_mac_address was just wrong and overwritten
by 02_network. Put the correct value in DTS and remove redundant
statement in 02_network:
- asus,rt-ac57u
6. For one device, MAC address defined in DTS is exchanged together
with lan_mac/wan_mac setup in 02_network, so that cases in
02_network can be merged:
- phicomm,k2p
For some devices, an empty case has to be used to prevent them
from falling into the default case and have
WAN address = eth0 address + 1 set to them.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 1c0290c5cc.
Dropping the nopad can make the padding overflow into the next erase
block on devices using a non-aligned rootfs start. This breaks the jffs2
overlay partition with the following messages:
[ 30.343877] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 30.376512] jffs2: Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[ 30.385253] jffs2: empty_blocks 196, bad_blocks 0, c->nr_blocks 197
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This provides TRX validation result to the validation JSON. It also
prevents users from installing broken firmware files.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
0f3c136 sysupgrade: set UPGRADE_BACKUP env variable
0bcbbbf system: fix uninitialized variables in firmware validation code
This update includes a fix for uninitialized variable usage.
Fixes: 7290963d09 ("procd: update to the latest git HEAD")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The actual retrieval of the MAC address in mtd_get_mac_binary_ubi()
is the same as in get_mac_binary(). Thus, use the latter function
in the former to reduce duplicate code.
This will also allow to benefit from the enhanced path check there
and bring mtd_get_mac_binary_ubi() more in line with the similar
mtd_get_mac_binary().
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mtd_get_mac_text helper method did not support hexadecimal offset
values, resulting them to break after 75bfc393ba ("treewide:
convert MAC address location offsets to hexadecimal")
This commit fixes this by evaluating the hexadecimal input,
converting them to decimal.
Signed-off-by: David Bauer <mail@david-bauer.net>
$CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz.
This change makes code more generic and allows refactoring $CONF_TAR.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Add BACKUP_FILE and use it when copying an archive to be restored
after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
That was a result of accidentally running "sed" twice on some files.
Fixes: 5797fe84a3 ("treewide: replace remaining (not working now) $SAVE_CONFIG uses")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG
Fixes: b534ba9611 ("base-files: pass "save_config" option to the "sysupgrade" method")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This updates the U-Boot which provides the host tools like mkimage to
version 2019.07.
The patches were cleaned up and it was checked if this still compiles
on Linux and FreeBSD.
CONFIG_FIT_SIGNATURE_MAX_SIZE is set to the default value.
The patch for libressl was merged upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
