When having two keys that start with the same characters and the second
key just has one character more nand_tffs_read and tffs_read return the
wrong value for the longer key. This is due to the usage of strncmp in
combination with the length of the shorter key which is usually first in
the list before the longer key and when strncmp matches, the search is
stopped. The problem only occurs when the length of the two keys is
different, not if just the last character is different. The fix is to
use strcmp and as such it will only return the value if the key (name)
and the key to look for (namefilter) have the same value and length. A
sample case returning wrong values is when keys macwlan and macwlan2 are
defined and querying macwlan2 returns the value for macwlan.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This increases the size of the iw_5.9-8fab0c9e-3_mips_24kc.ipk from
41166 to 41942 bytes by 776 bytes.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
This option is needed e.g. to use strongswan for IPSec.
BTW: This was the only target where this option was disabled.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This uses "hdparm" (if present) to get the harddisk into low
power mode on NAS set-ups.
Cc: Adrian Schmutzler <mail@adrianschmutzler.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on the discussion on the mailing list [1], the patch which was
reverted, it reverts only one patch without the subsequent ones.
This leads to the SoC scaling issue not using a CPU parent clock, but
it uses DDR clock. This is done for all variants, and it's wrong because
commits (hacks) that were using the DDR clock are no longer in the mainline kernel.
If someone has stability issues on 1.2 GHz, it should not affect all
routers (1 GHz, 800 MHz) and it should be rather consulted with guys, who are trying to
improve the situation in the kernel and not making the situation worse.
There are two solutions in cases of instability:
a) disable cpufreq
b) underclock it up to 1 GHz
This reverts commit 080a0b74e3.
[1] https://lists.openwrt.org/pipermail/openwrt-devel/2021-June/035702.html
CC: Pali Rohár <pali@kernel.org>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Follow the recommendations stated in the Turris Omnia DTS for eth2:
"In case SFP module is present, U-Boot has to enable the sfp node above,
remove phy-handle property, and add managed = "in-band-status" property."
The boot script is written in a way, that it works for all U-Boot
versions deployed by the vendor so far (2015.10-rc2, 2019.07).
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Kernel 5.4 receives a reduced set, just to make the SFP cage work.
While we are at it, move the patches accepted upstream to the 0xx series.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Kernel 5.10 receives the complete set of improvements from 5.11/5.12.
While we are at it, move the patches accepted upstream to the 0xx series.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Add the missing CONFIG_KCSAN (disabled). Found while making kernel_oldconfig on
an x86-64 subtarget.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Change procd_add_start_mount_trigger to procd_add_restart_mount_trigger
and make it call 'restart' instead of 'start'.
This is more useful as it allows to handle both cases, intial start of
a services as well as restarting services. Calling 'restart' on a
service which has not yet been started has the same result as calling
'start'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we have a generic sdcard upgrade method, which was copied from
the mvebu platform method, we can switch mvebu to the generic method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add a generic sdcard upgrade method instead of duplicating code in yet
another target, and add a feature flag to only install this upgrade
method in targets that set this flag. Copied from mvebu.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This uses "GPL-2.0-or-later" header for files identified using scancode
license scanner with 100% score as GPL 2.0 or later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
kirkwood build broke due to missing include needed for ETH_ALEN.
Add patch (sent upstream as well) to address that.
Refresh patches for 5.4 and 5.10.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The xfrm_interface module will not be built if IPv6 is not enabled in
the kernel. Add this dependency in the kmod package to avoid people
wondering why it doesn't build when they disabled IPv6.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As both the Mi Router 4A (100M) and the Mi Router 4C use the same
label-mac-device, the alias can be moved to the shared dtsi.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
A superflus ')' character has slipped into commit 91a52f22a1. Remove it
to fix build.
Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
e10de28 jail: cgroups-bpf: fix compile with musl 1.2
f5d9b14 hotplug-dispatch: fix rare memory leaks in error paths
Add new init script helpers:
procd_add_start_mount_trigger
procd_add_reload_mount_trigger
procd_get_mountpoints
Both trigger helpers expect a list of paths which are checked against
the mount targets configured in /etc/config/fstab and a trigger for all
mountpoints covered by the list of paths is setup.
procd_get_mountpoints is useful to find out if and which mountpoints
are covered by a list of paths.
Example:
DATADIRS="/mnt/data/foo /mnt/data/bar /etc/foo/baz /var/lib/doe"
start_service() {
[ "$_BOOT" = "1" ] &&
[ "$(procd_get_mountpoints $DATADIRS)" ] && return 0
procd_open_instance
# ...
procd_close_instance
}
boot() {
_BOOT=1 start
}
service_triggers() {
procd_add_start_mount_trigger $DATADIRS
}
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MT7622 provides are hardware RNG with upstream Linux driver. Enable
compilation of this driver to make use of the hardware RNG.
Signed-off-by: David Bauer <mail@david-bauer.net>
The GL-X300B is a industrial 4G LTE router based on the Qualcomm
QCA9531 SoC.
Specifications:
- Qualcomm QCA9531 @ 650 MHz
- 128 MB of RAM
- 16 MB of SPI NOR FLASH
- 2x 10/100 Mbps Ethernet
- 2.4GHz 802.11b/g/n
- 1x USB 2.0 (vbus driven by GPIO)
- 4x LED, driven by GPIO
- 1x button (reset)
- 1x mini pci-e slot (vcc driven by GPIO)
- RS-485 Serial Port (untested)
Flash instructions:
This firmware can be flashed using either sysupgrade from the GL.iNet
firmware or the recovery console as follows:
- Press and hold the reset button
- Connect power to the router, wait five seconds
- Manually configure 192.168.1.2/24 on your computer, connect to
192.168.1.1
- Upload the firmware image using the web interface
RS-485 serial port is untested and may depend on the following commit in
the GL.iNet repo:
202e83a32a
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
WAN eth0 label
LAN eth1 label + 1
2g phy0 label + 2
The label MAC address was found in the art partition at 0x0
Based on vendor commit:
16c5708b20
Signed-off-by: John Marrett <johnf@zioncluster.ca>
Add the missing ARM_SCMI_PROTOCOL symbol. Apparently it was exposed
for 5.10.53 with a kernel dependency change.
Missing symbol observed with mediatek/7622 E8450/RT3200 router.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The virtual cable tester depends on the netlink interface for ethtool.
Thus, enable it in the generic kernel configuration.
Signed-off-by: David Bauer <mail@david-bauer.net>
Netlink support is required for using the virtual cable tester
functionality.
Remove the pretty print build option and instead create a second package
variant ethtool-full. This allows users to install the full ethtool
featureset using opkg.
Signed-off-by: David Bauer <mail@david-bauer.net>
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Fix build on glibc targets and address a bunch of compiler warnings.
93fc089 jail: cgroups-bpf: don't use sys/reg.h when building with glibc
548d057 jail: don't ignore return value of seteuid()
220b716 jail: ignore return value when creating default /dev symlinks
78d5baa hotplug-dispatch: don't ignore asprintf() return value
736aee5 uxc: always handle asprintf() return value
2b20456 hotplug-dispatch: replace wrongly used assert()
bfc86a2 jail: cgroups: replace wrongly used assert()
516bdf2 jail: don't ignore return value of write()
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Try umount on device mapper and loop devices still mounted, so the
subsequent call to disactivate all physical volumes and delete all
loop devices is more likely to succeed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
141ac85 libblkid-tiny: fix invalid open syscall return check
9e26563 libblkid-tiny: install header file to include dir
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable xattr for the generated squashfs only if needed for SELinux.
This eliminates warnings during boot on target when building
(non-SELinux) OpenWrt on SELinux-enabled hosts like Fedora.
Reported-by: fda77 <fda77@users.noreply.github.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If the busybox applet losetup was selected, `command -v` selects that
during sysupgrade. As this applet is in another path and doesn't cover
the '-D' option which is used to make sure user-defined loop devices
are no longer active during sysupgrade.
Detect losetup at the path of the full utility to avoid error messages
in case of the busybox applet being selected.
Reported-by: fda77 <fda77@users.noreply.github.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
EXTRA_MOUNT variable should be reset in dnsmasq_start() rather than
just once at the beginning of the script.
Fixes: ac4e8aa2f8 ("dnsmasq: fix more dnsmasq jail issues")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* remove superflus mounts of /dev/null and /dev/urandom
* reset EXTRA_MOUNTS at the beginning of the script
* add mount according to ignore_hosts_dir
* don't add mount for file which is inside a directory already in the
EXTRA_MOUNTS list
Fixes: 59c63224e1 ("dnsmasq: rework jail mounts")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
