wifi-tally_Oostendam/nodemcu-firmware/lua_modules/mcp23008/mcp23008.lua
Eljakim Herrewijnen 50b5fc1824 Initial commit
2021-09-27 21:52:27 +02:00

163 lines
4.9 KiB
Lua

---
-- @description Expands the ESP8266's GPIO to 8 more I/O pins via I2C with the MCP23008 I/O Expander
-- MCP23008 Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/21919e.pdf
-- Tested on NodeMCU 0.9.5 build 20150213.
-- @date March 02, 2015
-- @author Miguel
-- GitHub: https://github.com/AllAboutEE
-- YouTube: https://www.youtube.com/user/AllAboutEE
-- Website: http://AllAboutEE.com
--------------------------------------------------------------------------------
local moduleName = ...
local M = {}
_G[moduleName] = M
-- Constant device address.
local MCP23008_ADDRESS = 0x20
-- Registers' address as defined in the MCP23008's datashseet
-- luacheck: push no unused
local MCP23008_IODIR = 0x00
local MCP23008_IPOL = 0x01
local MCP23008_GPINTEN = 0x02
local MCP23008_DEFVAL = 0x03
local MCP23008_INTCON = 0x04
local MCP23008_IOCON = 0x05
local MCP23008_GPPU = 0x06
local MCP23008_INTF = 0x07
local MCP23008_INTCAP = 0x08
local MCP23008_GPIO = 0x09
local MCP23008_OLAT = 0x0A
-- luacheck: pop
-- Default value for i2c communication
local id = 0
-- pin modes for I/O direction
M.INPUT = 1
M.OUTPUT = 0
-- pin states for I/O i.e. on/off
M.HIGH = 1
M.LOW = 0
-- Weak pull-up resistor state
M.ENABLE = 1
M.DISABLE = 0
---
-- @name write
-- @description Writes one byte to a register
-- @param registerAddress The register where we'll write data
-- @param data The data to write to the register
-- @return void
----------------------------------------------------------
local function write(registerAddress, data)
i2c.start(id)
i2c.address(id,MCP23008_ADDRESS,i2c.TRANSMITTER) -- send MCP's address and write bit
i2c.write(id,registerAddress)
i2c.write(id,data)
i2c.stop(id)
end
---
-- @name read
-- @description Reads the value of a regsiter
-- @param registerAddress The reigster address from which to read
-- @return The byte stored in the register
----------------------------------------------------------
local function read(registerAddress)
-- Tell the MCP which register you want to read from
i2c.start(id)
i2c.address(id,MCP23008_ADDRESS,i2c.TRANSMITTER) -- send MCP's address and write bit
i2c.write(id,registerAddress)
i2c.stop(id)
i2c.start(id)
-- Read the data form the register
i2c.address(id,MCP23008_ADDRESS,i2c.RECEIVER) -- send the MCP's address and read bit
local data = i2c.read(id,1) -- we expect only one byte of data
i2c.stop(id)
return string.byte(data) -- i2c.read returns a string so we convert to it's int value
end
---
--! @name begin
--! @description Sets the MCP23008 device address's last three bits.
-- Note: The address is defined as binary 0100[A2][A1][A0] where
-- A2, A1, and A0 are defined by the connection of the pins,
-- e.g. if the pins are connected all to GND then the paramter address
-- will need to be 0x0.
-- @param address The 3 least significant bits (LSB) of the address
-- @param pinSDA The pin to use for SDA
-- @param pinSCL The pin to use for SCL
-- @param speed The speed of the I2C signal
-- @return void
---------------------------------------------------------------------------
function M.begin(address,pinSDA,pinSCL,speed)
MCP23008_ADDRESS = bit.bor(MCP23008_ADDRESS,address)
i2c.setup(id,pinSDA,pinSCL,speed)
end
---
-- @name writeGPIO
-- @description Writes a byte of data to the GPIO register
-- @param dataByte The byte of data to write
-- @return void
----------------------------------------------------------
function M.writeGPIO(dataByte)
write(MCP23008_GPIO,dataByte)
end
---
-- @name readGPIO
-- @description reads a byte of data from the GPIO register
-- @return One byte of data
----------------------------------------------------------
function M.readGPIO()
return read(MCP23008_GPIO)
end
---
-- @name writeIODIR
-- @description Writes one byte of data to the IODIR register
-- @param dataByte The byte of data to write
-- @return void
----------------------------------------------------------
function M.writeIODIR(dataByte)
write(MCP23008_IODIR,dataByte)
end
---
-- @name readIODIR
-- @description Reads a byte from the IODIR register
-- @return The byte of data in IODIR
----------------------------------------------------------
function M.readIODIR()
return read(MCP23008_IODIR)
end
---
-- @name writeGPPU The byte to write to the GPPU
-- @description Writes a byte of data to the
-- PULL-UP RESISTOR CONFIGURATION (GPPU)REGISTER
-- @param databyte the value to write to the GPPU register.
-- each bit in this byte is assigned to an individual GPIO pin
-- @return void
----------------------------------------------------------------
function M.writeGPPU(dataByte)
write(MCP23008_GPPU,dataByte)
end
---
-- @name readGPPU
-- @description Reads the GPPU (Pull-UP resistors register) byte
-- @return The GPPU byte i.e. state of all internal pull-up resistors
-------------------------------------------------------------------
function M.readGPPU()
return read(MCP23008_GPPU)
end
return M