102 lines
4.5 KiB
Markdown
102 lines
4.5 KiB
Markdown
|
# Troubleshooting
|
|||
|
|
|
|||
|
|
The Troubleshooting Guide lists a few common symptoms and possible ways to resolve them.
|
|||
|
|
The hints are usually ordered from most likely to least likely.
|
|||
|
|
|
|||
|
|
## After powering the Tally the LED strip stays dark
|
|||
|
|
|
|||
|
|
If the LED strip started flashing blue before turning black, see [below](#the-led-strip-started-flashing-blue-for-a-while-but-then-turned-black).
|
|||
|
|
|
|||
|
|
* Is the Tally really powered? Is your battery pack empty? Could the connector cable be broken?
|
|||
|
|
* Did you upload all files to the Tally?
|
|||
|
|
* Is the LED strip correctly wired?
|
|||
|
|
* Is the LED strip working? Try to connect it to a 5V power source directly.
|
|||
|
|
* Are you using an LED strip with common cathode? Connect the common pin to `GND` and
|
|||
|
|
[do the necessary configuration](tally.md#using-leds-with-common-cathode).
|
|||
|
|
* Is the NodeMCU working? Try to connect to it via USB
|
|||
|
|
* In case you are developing the Tally Code: It is normal the strip stays black, because the
|
|||
|
|
`init.lua` file is not uploaded.
|
|||
|
|
|
|||
|
|
## The LED strip started flashing blue for a while but then turned black
|
|||
|
|
|
|||
|
|
* The Tally should usually recover from any errors and reboot automatically. But you could
|
|||
|
|
try reconnecting it to its power source to reboot it
|
|||
|
|
* The Stage Light stays black when the Tally is not patched in the Hub or not currently on
|
|||
|
|
Preview or Program on the Video Mixer. So this could be totally normal.
|
|||
|
|
|
|||
|
|
## The Tally slowly blinks blue for an extended amount of time
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
**This indicates issues when trying to connect to your WiFi.** It is perfectly normal to see
|
|||
|
|
this during boot up for a few seconds, but it should not sustain for long.
|
|||
|
|
|
|||
|
|
* Is your WiFi up? Is the signal strong enough near the tally?
|
|||
|
|
* Did you configure the WiFi name and its credentials correctly in `tally-settings.ini`?
|
|||
|
|
* Connect to the Tally via USB. It should log an error code why the connection failed.
|
|||
|
|
The error codes are explained in the [NodeMCU documentation](https://nodemcu.readthedocs.io/en/master/modules/wifi/#wifieventmonreason).
|
|||
|
|
|
|||
|
|
## The Tally blinks blue quickly for an extended amount of time
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
**This means the Tally has connected to your WiFi and is waiting to get an IP address.**
|
|||
|
|
It is perfectly normal to see this during boot up for a seconds, but it should not
|
|||
|
|
sustain for long.
|
|||
|
|
|
|||
|
|
This very likely points to an issue with your WiFi configuration.
|
|||
|
|
|
|||
|
|
* Does your WiFi run DHCP? Are there enough free addresses that your WiFi router could issue?
|
|||
|
|
|
|||
|
|
## The Tally blinks blue twice
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
**This indicates that the Tally can not connect to the hub.**
|
|||
|
|
|
|||
|
|
* Is the hub running?
|
|||
|
|
* Is the hubs IP correctly configured in `tally-settings.ini`? Did the IP address of the computer
|
|||
|
|
running the hub change?
|
|||
|
|
* Could there be a firewall blocking traffic between the Tally and the hub? Communication runs on port `{{ tally_default_port }}` by default.
|
|||
|
|
|
|||
|
|
## The Tally blinks blue three times
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
**This happens when the `tally-settings.ini` file does not exist or is invalid.**
|
|||
|
|
|
|||
|
|
* Did you flash the `tally-settings.ini` on the Tally?
|
|||
|
|
* Does the `tally-settings.ini` include all mandatory settings?
|
|||
|
|
* Try configuring "wrong" settings that won't work. But this way, you should get a different error and rule out
|
|||
|
|
that keys where mistyped.
|
|||
|
|
|
|||
|
|
## The Tally blinks blue occasionally
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
**This indicates that the tally is connected to the hub, but the hub does not know
|
|||
|
|
which signal the tally should show.**
|
|||
|
|
|
|||
|
|
* Did the hub connect to your Video Mixer?
|
|||
|
|
|
|||
|
|
## The colors on the LEDs are messed up
|
|||
|
|
|
|||
|
|
* Is the wiring correct?
|
|||
|
|
* It is not unheared of, that the pins of LEDs are not labeled correctly. Maybe switch them around.
|
|||
|
|
* If the colors that should be on are off and vice versa, you probably use an LED with common
|
|||
|
|
cathode. See the [tally documentation](tally.md#using-leds-with-common-cathode) how to fix it.
|
|||
|
|
|
|||
|
|
## The Hub can not connect to ATEM video mixer
|
|||
|
|
|
|||
|
|
**Are you really sure the settings are correct? If yes read further.**
|
|||
|
|
|
|||
|
|
Every ATEM mixer has a [maximum of connections](https://forum.blackmagicdesign.com/viewtopic.php?f=4&t=101841)
|
|||
|
|
that it allows at the same time – the Internet talks of 3-5 connections depending on the model.
|
|||
|
|
You might be running into this issue.
|
|||
|
|
|
|||
|
|
To verify this as the cause identify all other software / hardware that connects to the Video Mixer,
|
|||
|
|
restart it and make sure the Tally Hub is the first thing to connect.
|
|||
|
|
|
|||
|
|
The way to fix it is very dependent on your setup. See if you can dispense of any
|
|||
|
|
software / hardware connecting to ATEM.
|