87 lines
3.4 KiB
Markdown
87 lines
3.4 KiB
Markdown
|
# SoftUART Module
|
||
|
| Since | Origin / Contributor | Maintainer | Source |
|
||
|
| :----- | :-------------------- | :---------- | :------ |
|
||
|
|2019-12-27 | [pleningerweb](https://github.com/plieningerweb/), [juancgalvez](https://github.com/juancgalvez/), [crasu](https://github.com/crasu/), [galjonsfigur](https://github.com/galjonsfigur/)| [galjonsfigur](https://github.com/galjonsfigur/) | [softuart.c](../../app/modules/softuart.c) |
|
||
|
|
||
|
The SoftUART module offers bit-banged serial ports over GPIO pins.
|
||
|
|
||
|
!!! warning
|
||
|
|
||
|
Software implementation of serial port can be unreliable and some reception errors are to be expected.
|
||
|
|
||
|
ESP8266 has only 1 full hardware UART port that is used to program the chip and communicate with NodeMCU firmware. The second port is transmit-only. More information can be found in [uart module documentation](uart/). This module provides access to more UART ports and can be used to communicate with devices like GSM or GPS modules. The code is based on [esp8266-software-uart](https://github.com/plieningerweb/esp8266-software-uart) and [Arduino-esp8266-Software-UART](https://github.com/juancgalvez/Arduino-esp8266-Software-UART) projects. Currently doesn't support inverted serial data logic or modes other than 8N1. It's important to notice that this is a software implementation of the serial protocol. There could be some interrupts that make the transmission or reception fail due to invalid timing.
|
||
|
|
||
|
!!! note
|
||
|
|
||
|
SoftUART cannot be used on D0 pin.
|
||
|
|
||
|
## softuart.setup()
|
||
|
|
||
|
Creates new SoftUART instance. Note that rx pin cannot be shared between instances but tx pin can.
|
||
|
|
||
|
#### Syntax
|
||
|
`softuart.setup(baudrate, txPin, rxPin)`
|
||
|
|
||
|
#### Parameters
|
||
|
- `baudrate`: SoftUART baudrate. Maximum supported is 230400.
|
||
|
- `txPin`: SoftUART tx pin. If set to `nil` `write` method will not be supported.
|
||
|
- `rxPin`: SoftUART rx pin. If set to `nil` `on("data")` method will not be supported.
|
||
|
|
||
|
#### Returns
|
||
|
`softuart` instance.
|
||
|
|
||
|
#### Example
|
||
|
```lua
|
||
|
-- Create new software UART with baudrate of 9600, D2 as Tx pin and D3 as Rx pin
|
||
|
s = softuart.setup(9600, 2, 3)
|
||
|
```
|
||
|
|
||
|
# SoftUART port
|
||
|
|
||
|
|
||
|
## softuart.port:on()
|
||
|
Sets up the callback function to receive data.
|
||
|
|
||
|
#### Syntax
|
||
|
`softuart.port:on(event, trigger, function(data))`
|
||
|
|
||
|
#### Parameters
|
||
|
- `event`: Event name. Currently only `data` is supported.
|
||
|
- `trigger`: Can be a character or a number. If character is set, the callback function will only be run when that character gets received. When a number is set, the callback function will only be run when buffer will have as many characters as number.
|
||
|
- `function(data)`: Callback function. the `data` parameter is software UART receiving buffer.
|
||
|
|
||
|
#### Returns
|
||
|
`nil`
|
||
|
|
||
|
#### Example
|
||
|
```lua
|
||
|
-- Create new software UART with baudrate of 9600, D2 as Tx pin and D3 as Rx pin
|
||
|
s = softuart.setup(9600, 2, 3)
|
||
|
-- Set callback to run when 10 characters show up in the buffer
|
||
|
s:on("data", 10, function(data)
|
||
|
print("Lua handler called!")
|
||
|
print(data)
|
||
|
end)
|
||
|
```
|
||
|
|
||
|
## softuart.port:write()
|
||
|
Transmits a byte or sequence of them.
|
||
|
|
||
|
#### Syntax
|
||
|
`softuart.port:write(data)`
|
||
|
|
||
|
#### Parameters
|
||
|
- `data`: Can be a number or string. When a number is passed, only one byte will be sent. When a string is passed, whole sequence will be transmitted.
|
||
|
|
||
|
#### Returns
|
||
|
`nil`
|
||
|
|
||
|
#### Example
|
||
|
```lua
|
||
|
-- Create new software UART with baudrate of 9600, D2 as Tx pin and D3 as Rx pin
|
||
|
s = softuart.setup(9600, 2, 3)
|
||
|
s:write("Hello!")
|
||
|
-- Send character 'a'
|
||
|
s:write(97)
|
||
|
```
|