4a77a060ab
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
706 lines
21 KiB
Makefile
706 lines
21 KiB
Makefile
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
|
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
|
|
DEVICE_VARS += WRGG_DEVNAME WRGG_SIGNATURE
|
|
|
|
define Device/Default
|
|
PROFILES := Default
|
|
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
|
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
|
|
KERNEL_PREFIX := $$(IMAGE_PREFIX)
|
|
KERNEL_LOADADDR := 0x80208000
|
|
DEVICE_DTS = $$(SOC)-$(lastword $(subst _, ,$(1)))
|
|
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
|
|
IMAGE/sysupgrade.bin/squashfs :=
|
|
endef
|
|
|
|
define Device/FitImage
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/FitImageLzma
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/FitzImage
|
|
KERNEL_SUFFIX := -fit-zImage.itb
|
|
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := zImage
|
|
endef
|
|
|
|
define Device/UbiFit
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES := nand-factory.ubi nand-sysupgrade.bin
|
|
IMAGE/nand-factory.ubi := append-ubi
|
|
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/DniImage
|
|
$(call Device/FitzImage)
|
|
NETGEAR_BOARD_ID :=
|
|
NETGEAR_HW_ID :=
|
|
IMAGES += factory.img
|
|
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | \
|
|
append-rootfs | pad-rootfs | append-metadata | check-size
|
|
endef
|
|
|
|
define Build/append-rootfshdr
|
|
mkimage -A $(LINUX_KARCH) \
|
|
-O linux -T filesystem \
|
|
-C lzma -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
|
|
-n root.squashfs -d $(IMAGE_ROOTFS) $@.new
|
|
dd if=$@.new bs=64 count=1 >> $(IMAGE_KERNEL)
|
|
endef
|
|
|
|
define Build/mkmylofw_32m
|
|
$(eval device_id=$(word 1,$(1)))
|
|
$(eval revision=$(word 2,$(1)))
|
|
|
|
let \
|
|
size="$$(stat -c%s $@)" \
|
|
pad="$(subst k,* 1024,$(BLOCKSIZE))" \
|
|
pad="(pad - (size % pad)) % pad" \
|
|
newsize='size + pad'; \
|
|
$(STAGING_DIR_HOST)/bin/mkmylofw \
|
|
-B WPE72 -i 0x11f6:$(device_id):0x11f6:$(device_id) -r $(revision) \
|
|
-s 0x2000000 -p0x180000:$$newsize:al:0x80208000:"OpenWrt":$@ \
|
|
$@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Build/qsdk-ipq-factory-nand-askey
|
|
$(TOPDIR)/scripts/mkits-qsdk-ipq-image.sh $@.its\
|
|
askey_kernel $(IMAGE_KERNEL) \
|
|
askey_fs $(IMAGE_ROOTFS) \
|
|
ubifs $@
|
|
PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
|
|
@mv $@.new $@
|
|
endef
|
|
|
|
define Build/SenaoFW
|
|
-$(STAGING_DIR_HOST)/bin/mksenaofw \
|
|
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
|
|
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
|
|
-e $@ \
|
|
-o $@.new
|
|
@cp $@.new $@
|
|
endef
|
|
|
|
define Build/wrgg-image
|
|
mkwrggimg -i $@ \
|
|
-o $@.new \
|
|
-d "$(WRGG_DEVNAME)" \
|
|
-s "$(WRGG_SIGNATURE)" \
|
|
-v "" -m "" -B ""
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Device/8dev_habanero-dvk
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Habanero DVK
|
|
IMAGE_SIZE := 30976k
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := ipq-wifi-8dev_habanero-dvk
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | append-metadata | check-size
|
|
endef
|
|
TARGET_DEVICES += 8dev_habanero-dvk
|
|
|
|
define Device/8dev_jalapeno-common
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
SOC := qcom-ipq4018
|
|
endef
|
|
|
|
define Device/8dev_jalapeno
|
|
$(call Device/8dev_jalapeno-common)
|
|
DEVICE_VENDOR := 8devices
|
|
DEVICE_MODEL := Jalapeno
|
|
endef
|
|
TARGET_DEVICES += 8dev_jalapeno
|
|
|
|
define Device/alfa-network_ap120c-ac
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := ALFA Network
|
|
DEVICE_MODEL := AP120C-AC
|
|
SOC := qcom-ipq4018
|
|
DEVICE_PACKAGES := kmod-usb-acm \
|
|
kmod-tpm-i2c-atmel uboot-envtools
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
IMAGE_SIZE := 65536k
|
|
IMAGES := nand-factory.bin nand-sysupgrade.bin
|
|
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
|
|
endef
|
|
TARGET_DEVICES += alfa-network_ap120c-ac
|
|
|
|
define Device/aruba_glenmorangie
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := Aruba
|
|
SOC := qcom-ipq4029
|
|
DEVICE_PACKAGES := ipq-wifi-aruba_ap-303
|
|
endef
|
|
|
|
define Device/aruba_ap-303
|
|
$(call Device/aruba_glenmorangie)
|
|
DEVICE_MODEL := AP-303
|
|
endef
|
|
TARGET_DEVICES += aruba_ap-303
|
|
|
|
define Device/aruba_ap-303h
|
|
$(call Device/aruba_glenmorangie)
|
|
DEVICE_MODEL := AP-303H
|
|
endef
|
|
TARGET_DEVICES += aruba_ap-303h
|
|
|
|
define Device/aruba_ap-365
|
|
$(call Device/aruba_glenmorangie)
|
|
DEVICE_MODEL := AP-365
|
|
DEVICE_PACKAGES += kmod-hwmon-ad7418
|
|
endef
|
|
TARGET_DEVICES += aruba_ap-365
|
|
|
|
define Device/asus_map-ac2200
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := Lyra (MAP-AC2200)
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
|
|
endef
|
|
TARGET_DEVICES += asus_map-ac2200
|
|
|
|
define Device/asus_rt-ac58u
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := ASUS
|
|
DEVICE_MODEL := RT-AC58U
|
|
SOC := qcom-ipq4018
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DTB_SIZE := 65536
|
|
IMAGE_SIZE := 20439364
|
|
FILESYSTEMS := squashfs
|
|
# Someone - in their infinite wisdom - decided to put the firmware
|
|
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
|
|
# Since u-boot works with strings we either need another fixup step
|
|
# to add a version... or we are very careful not to add '\0' into that
|
|
# string and call it a day.... Yeah, we do the latter!
|
|
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
|
|
kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += asus_rt-ac58u
|
|
|
|
define Device/avm_fritzbox-4040
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := AVM
|
|
DEVICE_MODEL := FRITZ!Box 4040
|
|
SOC := qcom-ipq4018
|
|
BOARD_NAME := fritz4040
|
|
IMAGE_SIZE := 29056k
|
|
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
|
|
UBOOT_PARTITION_SIZE := 524288
|
|
IMAGES += eva.bin
|
|
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size
|
|
DEVICE_PACKAGES := fritz-tffs fritz-caldata
|
|
endef
|
|
TARGET_DEVICES += avm_fritzbox-4040
|
|
|
|
define Device/avm_fritzbox-7530
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := AVM
|
|
DEVICE_MODEL := FRITZ!Box 7530
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
|
|
endef
|
|
TARGET_DEVICES += avm_fritzbox-7530
|
|
|
|
define Device/avm_fritzrepeater-1200
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := AVM
|
|
DEVICE_MODEL := FRITZ!Repeater 1200
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-1200
|
|
endef
|
|
TARGET_DEVICES += avm_fritzrepeater-1200
|
|
|
|
define Device/avm_fritzrepeater-3000
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := AVM
|
|
DEVICE_MODEL := FRITZ!Repeater 3000
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
|
|
endef
|
|
TARGET_DEVICES += avm_fritzrepeater-3000
|
|
|
|
define Device/buffalo_wtr-m2133hp
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Buffalo
|
|
DEVICE_MODEL := WTR-M2133HP
|
|
SOC := qcom-ipq4019
|
|
DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9984-ct ipq-wifi-buffalo_wtr-m2133hp
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
endef
|
|
TARGET_DEVICES += buffalo_wtr-m2133hp
|
|
|
|
define Device/cellc_rtl30vw
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb | uImage lzma | pad-to 2048
|
|
KERNEL_NAME := Image
|
|
KERNEL_IN_UBI :=
|
|
IMAGES := nand-factory.bin nand-sysupgrade.bin
|
|
IMAGE/nand-factory.bin := append-rootfshdr | append-ubi | qsdk-ipq-factory-nand-askey
|
|
IMAGE/nand-sysupgrade.bin := append-rootfshdr | sysupgrade-tar | append-metadata
|
|
DEVICE_VENDOR := Cell C
|
|
DEVICE_MODEL := RTL30VW
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@5
|
|
KERNEL_INSTALL := 1
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 57344k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi ipq-wifi-cellc_rtl30vw
|
|
endef
|
|
TARGET_DEVICES += cellc_rtl30vw
|
|
|
|
define Device/cilab_meshpoint-one
|
|
$(call Device/8dev_jalapeno-common)
|
|
DEVICE_VENDOR := Crisis Innovation Lab
|
|
DEVICE_MODEL := MeshPoint.One
|
|
DEVICE_PACKAGES := kmod-i2c-gpio kmod-iio-bmp280-i2c kmod-hwmon-ina2xx kmod-rtc-pcf2127
|
|
endef
|
|
TARGET_DEVICES += cilab_meshpoint-one
|
|
|
|
define Device/compex_wpj419
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ419
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@12
|
|
KERNEL_INSTALL := 1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
FILESYSTEMS := squashfs
|
|
endef
|
|
TARGET_DEVICES += compex_wpj419
|
|
|
|
define Device/compex_wpj428
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Compex
|
|
DEVICE_MODEL := WPJ428
|
|
SOC := qcom-ipq4028
|
|
DEVICE_DTS_CONFIG := config@4
|
|
BLOCKSIZE := 64k
|
|
IMAGE_SIZE := 31232k
|
|
KERNEL_SIZE := 4096k
|
|
IMAGES += cpximg-6a04.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGE/cpximg-6a04.bin := append-kernel | append-rootfs | pad-rootfs | mkmylofw_32m 0x8A2 3
|
|
DEVICE_PACKAGES := kmod-gpio-beeper
|
|
endef
|
|
TARGET_DEVICES += compex_wpj428
|
|
|
|
define Device/dlink_dap-2610
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := D-Link
|
|
DEVICE_MODEL := DAP-2610
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@ap.dk01.1-c1
|
|
BLOCKSIZE := 64k
|
|
WRGG_DEVNAME := /dev/mtdblock/8
|
|
WRGG_SIGNATURE := wapac30_dkbs_dap2610
|
|
IMAGE_SIZE := 14080k
|
|
IMAGES += factory.bin
|
|
# Bootloader expects a special 160 byte header which is added by
|
|
# wrgg-image.
|
|
# Factory image size must be larger than 6MB, and size in wrgg header must
|
|
# match actual factory image size to be flashable from D-Link http server.
|
|
# Bootloader verifies checksum of wrgg image before booting, thus jffs2
|
|
# cannot be part of the wrgg image. This is solved in the factory image by
|
|
# having the rootfs at the end of the image (without pad-rootfs). And in
|
|
# the sysupgrade image only the kernel is included in the wrgg checksum,
|
|
# but this is not flashable from the D-link http server.
|
|
# append-rootfs must start on an erase block boundary.
|
|
IMAGE/factory.bin := append-kernel | pad-offset 6144k 160 | append-rootfs | wrgg-image | check-size
|
|
IMAGE/sysupgrade.bin := append-kernel | wrgg-image | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-dlink_dap2610
|
|
endef
|
|
TARGET_DEVICES += dlink_dap-2610
|
|
|
|
define Device/engenius_eap1300
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP1300
|
|
DEVICE_DTS_CONFIG := config@4
|
|
BOARD_NAME := eap1300
|
|
SOC := qcom-ipq4018
|
|
KERNEL_SIZE := 5120k
|
|
IMAGE_SIZE := 25344k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += engenius_eap1300
|
|
|
|
define Device/engenius_eap2200
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EAP2200
|
|
SOC := qcom-ipq4019
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-engenius_eap2200 -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
|
endef
|
|
TARGET_DEVICES += engenius_eap2200
|
|
|
|
define Device/engenius_emd1
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EMD1
|
|
DEVICE_DTS_CONFIG := config@4
|
|
SOC := qcom-ipq4018
|
|
IMAGE_SIZE := 30720k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
|
endef
|
|
TARGET_DEVICES += engenius_emd1
|
|
|
|
define Device/engenius_emr3500
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := EMR3500
|
|
DEVICE_DTS_CONFIG := config@4
|
|
SOC := qcom-ipq4018
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 30720k
|
|
IMAGES += factory.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size
|
|
endef
|
|
TARGET_DEVICES += engenius_emr3500
|
|
|
|
define Device/engenius_ens620ext
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EnGenius
|
|
DEVICE_MODEL := ENS620EXT
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@4
|
|
BLOCKSIZE := 64k
|
|
PAGESIZE := 256
|
|
BOARD_NAME := ENS620EXT
|
|
VENDOR_ID := 0x0101
|
|
PRODUCT_ID := 0x79
|
|
PRODUCT_ID_NEW := 0xA4
|
|
DATECODE := 190507
|
|
FW_VER := 3.1.2
|
|
FW_VER_NEW := 3.5.6
|
|
CW_VER := 1.8.99
|
|
IMAGE_SIZE := 21312k
|
|
KERNEL_SIZE := 5120k
|
|
FILESYSTEMS := squashfs
|
|
IMAGES += factory_30.bin factory_35.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size | append-metadata
|
|
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
|
|
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
|
|
endef
|
|
TARGET_DEVICES += engenius_ens620ext
|
|
|
|
define Device/ezviz_cs-w3-wd1200g-eup
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := EZVIZ
|
|
DEVICE_MODEL := CS-W3-WD1200G
|
|
DEVICE_VARIANT := EUP
|
|
DEVICE_DTS_CONFIG := config@4
|
|
IMAGE_SIZE := 14848k
|
|
SOC := qcom-ipq4018
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
|
|
append-metadata
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers \
|
|
ipq-wifi-ezviz_cs-w3-wd1200g-eup
|
|
endef
|
|
TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
|
|
|
|
define Device/glinet_gl-b1300
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-B1300
|
|
BOARD_NAME := gl-b1300
|
|
SOC := qcom-ipq4029
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-b1300
|
|
|
|
define Device/glinet_gl-s1300
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := GL.iNet
|
|
DEVICE_MODEL := GL-S1300
|
|
SOC := qcom-ipq4029
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
IMAGES := sysupgrade.bin
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-glinet_gl-s1300 kmod-fs-ext4 kmod-mmc kmod-spi-dev
|
|
endef
|
|
TARGET_DEVICES += glinet_gl-s1300
|
|
|
|
define Device/linksys_ea6350v3
|
|
# The Linksys EA6350v3 has a uboot bootloader that does not
|
|
# support either booting lzma kernel images nor booting UBI
|
|
# partitions. This uboot, however, supports raw kernel images and
|
|
# gzipped images.
|
|
#
|
|
# As for the time of writing this, the device will boot the kernel
|
|
# from a fixed address with a fixed length of 3MiB. Also, the
|
|
# device has a hard-coded kernel command line that requieres the
|
|
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
|
|
# Oh... and the kernel partition overlaps with the rootfs
|
|
# partition (the same for alt_kernel and alt_rootfs).
|
|
#
|
|
# If you are planing re-partitioning the device, you may want to
|
|
# keep those details in mind:
|
|
# 1. The kernel adresses you should honor are 0x00000000 and
|
|
# 0x02800000 respectively.
|
|
# 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
|
|
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
|
|
# 4. The kernel command line from uboot is harcoded to boot with
|
|
# rootfs either in mtd11 or mtd13.
|
|
$(call Device/FitzImage)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := EA6350
|
|
DEVICE_VARIANT := v3
|
|
SOC := qcom-ipq4018
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
KERNEL_SIZE := 3072k
|
|
IMAGE_SIZE := 37888k
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += linksys_ea6350v3
|
|
|
|
define Device/linksys_ea8300
|
|
$(call Device/FitzImage)
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_MODEL := EA8300
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 3072k
|
|
IMAGE_SIZE := 87040k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
|
|
DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += linksys_ea8300
|
|
|
|
define Device/meraki_mr33
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Cisco Meraki
|
|
DEVICE_MODEL := MR33
|
|
SOC := qcom-ipq4029
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
|
|
endef
|
|
TARGET_DEVICES += meraki_mr33
|
|
|
|
define Device/mobipromo_cm520-79f
|
|
$(call Device/FitzImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := MobiPromo
|
|
DEVICE_MODEL := CM520-79F
|
|
SOC := qcom-ipq4019
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ipq-wifi-mobipromo_cm520-79f kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += mobipromo_cm520-79f
|
|
|
|
define Device/netgear_ex61x0v2
|
|
$(call Device/DniImage)
|
|
DEVICE_DTS_CONFIG := config@4
|
|
NETGEAR_BOARD_ID := EX6150v2series
|
|
NETGEAR_HW_ID := 29765285+16+0+128+2x2
|
|
IMAGE_SIZE := 14400k
|
|
SOC := qcom-ipq4018
|
|
endef
|
|
|
|
define Device/netgear_ex6100v2
|
|
$(call Device/netgear_ex61x0v2)
|
|
DEVICE_VENDOR := Netgear
|
|
DEVICE_MODEL := EX6100
|
|
DEVICE_VARIANT := v2
|
|
endef
|
|
TARGET_DEVICES += netgear_ex6100v2
|
|
|
|
define Device/netgear_ex6150v2
|
|
$(call Device/netgear_ex61x0v2)
|
|
DEVICE_VENDOR := Netgear
|
|
DEVICE_MODEL := EX6150
|
|
DEVICE_VARIANT := v2
|
|
endef
|
|
TARGET_DEVICES += netgear_ex6150v2
|
|
|
|
define Device/openmesh_a42
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_MODEL := A42
|
|
SOC := qcom-ipq4018
|
|
DEVICE_DTS_CONFIG := config@om.a42
|
|
BLOCKSIZE := 64k
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 15616k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
endef
|
|
TARGET_DEVICES += openmesh_a42
|
|
|
|
define Device/openmesh_a62
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := OpenMesh
|
|
DEVICE_MODEL := A62
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS_CONFIG := config@om.a62
|
|
BLOCKSIZE := 64k
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
IMAGE_SIZE := 15552k
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
|
|
endef
|
|
|
|
TARGET_DEVICES += openmesh_a62
|
|
|
|
define Device/qcom_ap-dk01.1-c1
|
|
DEVICE_VENDOR := Qualcomm Atheros
|
|
DEVICE_MODEL := AP-DK01.1
|
|
DEVICE_VARIANT := C1
|
|
BOARD_NAME := ap-dk01.1-c1
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
|
|
KERNEL_INSTALL := 1
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 26624k
|
|
$(call Device/FitImage)
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += qcom_ap-dk01.1-c1
|
|
|
|
define Device/qcom_ap-dk04.1-c1
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Qualcomm Atheros
|
|
DEVICE_MODEL := AP-DK04.1
|
|
DEVICE_VARIANT := C1
|
|
SOC := qcom-ipq4019
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
|
|
KERNEL_INSTALL := 1
|
|
KERNEL_SIZE := 4048k
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
BOARD_NAME := ap-dk04.1-c1
|
|
endef
|
|
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
|
|
|
define Device/qxwlan_e2600ac-c1
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E2600AC
|
|
DEVICE_VARIANT := C1
|
|
BOARD_NAME := e2600ac-c1
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 31232k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e2600ac-c1
|
|
|
|
define Device/qxwlan_e2600ac-c2
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := Qxwlan
|
|
DEVICE_MODEL := E2600AC
|
|
DEVICE_VARIANT := C2
|
|
SOC := qcom-ipq4019
|
|
KERNEL_INSTALL := 1
|
|
BLOCKSIZE := 128k
|
|
PAGESIZE := 2048
|
|
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
|
endef
|
|
TARGET_DEVICES += qxwlan_e2600ac-c2
|
|
|
|
define Device/unielec_u4019-32m
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := Unielec
|
|
DEVICE_MODEL := U4019
|
|
DEVICE_VARIANT := 32M
|
|
BOARD_NAME := u4019-32m
|
|
SOC := qcom-ipq4019
|
|
KERNEL_SIZE := 4096k
|
|
IMAGE_SIZE := 31232k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
endef
|
|
TARGET_DEVICES += unielec_u4019-32m
|
|
|
|
define Device/zyxel_nbg6617
|
|
$(call Device/FitImageLzma)
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NBG6617
|
|
SOC := qcom-ipq4018
|
|
KERNEL_SIZE := 4096k
|
|
ROOTFS_SIZE := 24960k
|
|
RAS_BOARD := NBG6617
|
|
RAS_ROOTFS_SIZE := 19840k
|
|
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
IMAGES += factory.bin
|
|
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
|
|
# at least as large as the one of the initial firmware image (not the current
|
|
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
|
|
# this minimum-size. However, the larger image can be flashed both ways.
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
|
|
endef
|
|
TARGET_DEVICES += zyxel_nbg6617
|
|
|
|
define Device/zyxel_wre6606
|
|
$(call Device/FitImage)
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := WRE6606
|
|
DEVICE_DTS_CONFIG := config@4
|
|
SOC := qcom-ipq4018
|
|
IMAGE_SIZE := 13184k
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size
|
|
DEVICE_PACKAGES := -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
|
|
endef
|
|
TARGET_DEVICES += zyxel_wre6606
|
|
|
|
$(eval $(call BuildImage))
|