Openwrt/target/linux/at91/patches-2.6.25/008-fdl-serial.patch
Gabor Juhos 104b3386a2 update to 2.6.25.12
SVN-Revision: 11933
2008-07-26 10:53:23 +00:00

162 lines
4.1 KiB
Diff

--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -214,6 +214,34 @@
at91_set_gpio_value(AT91_PIN_PA21, 0);
else
at91_set_gpio_value(AT91_PIN_PA21, 1);
+
+ /*
+ * FDL VersaLink adds GPIOS to provide full modem
+ * control on USART 0 - Drive DTR and RI pins manually
+ */
+ if (mctrl & TIOCM_DTR)
+ at91_set_gpio_value(AT91_PIN_PB6, 0);
+ else
+ at91_set_gpio_value(AT91_PIN_PB6, 1);
+ if (mctrl & TIOCM_RI)
+ at91_set_gpio_value(AT91_PIN_PB7, 0);
+ else
+ at91_set_gpio_value(AT91_PIN_PB7, 1);
+ }
+
+ /*
+ * FDL VersaLink adds GPIOS to provide full modem control on
+ * USART 3 - Drive DTR and RI pins manually
+ */
+ if (port->mapbase == AT91RM9200_BASE_US3) {
+ if (mctrl & TIOCM_DTR)
+ at91_set_gpio_value(AT91_PIN_PB29, 0);
+ else
+ at91_set_gpio_value(AT91_PIN_PB29, 1);
+ if (mctrl & TIOCM_RI)
+ at91_set_gpio_value(AT91_PIN_PB2, 0);
+ else
+ at91_set_gpio_value(AT91_PIN_PB2, 1);
}
}
#endif
@@ -251,8 +279,10 @@
/*
* The control signals are active low.
*/
- if (!(status & ATMEL_US_DCD))
- ret |= TIOCM_CD;
+
+ if (!(port->mapbase == AT91RM9200_BASE_US0 || port->mapbase == AT91RM9200_BASE_US3))
+ if (!(status & ATMEL_US_DCD))
+ ret |= TIOCM_CD;
if (!(status & ATMEL_US_CTS))
ret |= TIOCM_CTS;
if (!(status & ATMEL_US_DSR))
@@ -260,6 +290,16 @@
if (!(status & ATMEL_US_RI))
ret |= TIOCM_RI;
+ /*
+ * Read the GPIO's for the FDL VersaLink special case
+ */
+ if (port->mapbase == AT91RM9200_BASE_US0)
+ if (!(at91_get_gpio_value(AT91_PIN_PA19)))
+ ret |= TIOCM_CD;
+ if (port->mapbase == AT91RM9200_BASE_US3)
+ if (!(at91_get_gpio_value(AT91_PIN_PA24)))
+ ret |= TIOCM_CD;
+
return ret;
}
@@ -453,6 +493,34 @@
}
/*
+ * USART0 DCD Interrupt handler
+ */
+
+static irqreturn_t atmel_u0_DCD_interrupt(int irq, void *dev_id)
+{
+ struct uart_port *port = dev_id;
+ int status = at91_get_gpio_value(irq);
+
+ uart_handle_dcd_change(port, !(status));
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * USART3 DCD Interrupt handler
+ */
+
+static irqreturn_t atmel_u3_DCD_interrupt(int irq, void *dev_id)
+{
+ struct uart_port *port = dev_id;
+ int status = at91_get_gpio_value(irq);
+
+ uart_handle_dcd_change(port, !(status));
+
+ return IRQ_HANDLED;
+}
+
+/*
* receive interrupt handler.
*/
static void
@@ -815,6 +883,23 @@
return retval;
}
+ if (port->mapbase == AT91RM9200_BASE_US0) {
+ retval = request_irq(AT91_PIN_PA19, atmel_u0_DCD_interrupt, 0, "atmel_serial", port);
+ if (retval) {
+ printk("atmel_serial: atmel_startup - Can't get u0DCD irq\n");
+ free_irq(port->irq, port);
+ return retval;
+ }
+ }
+ if (port->mapbase == AT91RM9200_BASE_US3) {
+ retval = request_irq(AT91_PIN_PA24, atmel_u3_DCD_interrupt, 0, "atmel_serial", port);
+ if (retval) {
+ printk("atmel_serial: atmel_startup - Can't get u3DCD irq\n");
+ free_irq(port->irq, port);
+ return retval;
+ }
+ }
+
/*
* Initialize DMA (if necessary)
*/
@@ -834,6 +919,10 @@
kfree(atmel_port->pdc_rx[0].buf);
}
free_irq(port->irq, port);
+ if (port->mapbase == AT91RM9200_BASE_US0)
+ free_irq(AT91_PIN_PA19, port);
+ if (port->mapbase == AT91RM9200_BASE_US3)
+ free_irq(AT91_PIN_PA24, port);
return -ENOMEM;
}
pdc->dma_addr = dma_map_single(port->dev,
@@ -873,7 +962,11 @@
retval = atmel_open_hook(port);
if (retval) {
free_irq(port->irq, port);
- return retval;
+ if (port->mapbase == AT91RM9200_BASE_US0)
+ free_irq(AT91_PIN_PA19, port);
+ if (port->mapbase == AT91RM9200_BASE_US3)
+ free_irq(AT91_PIN_PA24, port);
+ return retval;
}
}
@@ -947,6 +1040,10 @@
* Free the interrupt
*/
free_irq(port->irq, port);
+ if (port->mapbase == AT91RM9200_BASE_US0)
+ free_irq(AT91_PIN_PA19, port);
+ if (port->mapbase == AT91RM9200_BASE_US3)
+ free_irq(AT91_PIN_PA24, port);
/*
* If there is a specific "close" function (to unregister