51fe956c4f
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
535 lines
9.1 KiB
Plaintext
535 lines
9.1 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
#include "qcom-ipq8064-v2.0.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "Buffalo WXR-2533DHP";
|
|
compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
|
|
|
|
memory@42000000 {
|
|
reg = <0x42000000 0x1e000000>;
|
|
device_type = "memory";
|
|
};
|
|
|
|
reserved-memory {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
rsvd@41200000 {
|
|
reg = <0x41200000 0x300000>;
|
|
no-map;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
serial0 = &gsbi4_serial;
|
|
|
|
led-boot = &power;
|
|
led-failsafe = &diag;
|
|
led-running = &power;
|
|
led-upgrade = &power;
|
|
};
|
|
|
|
chosen {
|
|
/* use "ubi_rootfs" volume in "ubi" partition as rootfs */
|
|
bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
soc {
|
|
nand@1ac00000 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&nand_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
cs@0 {
|
|
reg = <0>;
|
|
compatible = "qcom,nandcs";
|
|
|
|
nand-ecc-strength = <4>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-step-size = <512>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
ubi@0 {
|
|
label = "ubi";
|
|
reg = <0x0000000 0x4000000>;
|
|
};
|
|
|
|
rootfs_1@4000000 {
|
|
label = "rootfs_1";
|
|
reg = <0x4000000 0x4000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
mdio {
|
|
compatible = "virtual,mdio-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
|
|
<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-0 = <&mdio0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
ethernet-phy@0 {
|
|
reg = <0>;
|
|
qca,ar8327-initvals = <
|
|
0x00004 0x07600000 /* PAD0_MODE */
|
|
0x00008 0x01000000 /* PAD5_MODE */
|
|
0x0000c 0x00000080 /* PAD6_MODE */
|
|
0x00050 0xcc35cc35 /* LED_CTRL0 */
|
|
0x00054 0xca35ca35 /* LED_CTRL1 */
|
|
0x00058 0xc935c935 /* LED_CTRL2 */
|
|
0x0005c 0x03ffff00 /* LED_CTRL3 */
|
|
0x000e4 0x0006a545 /* MAC_POWER_SEL */
|
|
0x000e0 0xc74164de /* SGMII_CTRL */
|
|
0x0007c 0x0000007e /* PORT0_STATUS */
|
|
0x00094 0x0000007e /* PORT6_STATUS */
|
|
>;
|
|
};
|
|
|
|
ethernet-phy@4 {
|
|
reg = <4>;
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-0 = <&led_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
usb {
|
|
label = "wxr-2533dhp:green:usb";
|
|
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "usbport";
|
|
trigger-sources = <&hub_port0 &hub_port1>;
|
|
};
|
|
|
|
guestport {
|
|
label = "wxr-2533dhp:green:guestport";
|
|
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
diag: diag {
|
|
label = "wxr-2533dhp:orange:diag";
|
|
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
internet_orange {
|
|
label = "wxr-2533dhp:orange:internet";
|
|
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
internet_white {
|
|
label = "wxr-2533dhp:white:internet";
|
|
gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wireless_orange {
|
|
label = "wxr-2533dhp:orange:wireless";
|
|
gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wireless_white {
|
|
label = "wxr-2533dhp:white:wireless";
|
|
gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
router_orange {
|
|
label = "wxr-2533dhp:orange:router";
|
|
gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
router_white {
|
|
label = "wxr-2533dhp:white:router";
|
|
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
power: power {
|
|
label = "wxr-2533dhp:white:power";
|
|
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
pinctrl-0 = <&button_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
power {
|
|
label = "power";
|
|
gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_POWER>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
eject {
|
|
label = "eject";
|
|
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_EJECTCD>;
|
|
};
|
|
|
|
guest {
|
|
label = "guest";
|
|
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
};
|
|
|
|
ap {
|
|
label = "ap";
|
|
gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
router {
|
|
label = "router";
|
|
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
auto {
|
|
label = "auto";
|
|
gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&adm_dma {
|
|
status = "okay";
|
|
};
|
|
|
|
&gmac1 {
|
|
status = "okay";
|
|
|
|
phy-mode = "rgmii";
|
|
qcom,id = <1>;
|
|
|
|
pinctrl-0 = <&rgmii2_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
mtd-mac-address = <&ART 6>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&gmac2 {
|
|
status = "ok";
|
|
|
|
phy-mode = "sgmii";
|
|
qcom,id = <2>;
|
|
|
|
mtd-mac-address = <&ART 0>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&gsbi4 {
|
|
status = "okay";
|
|
qcom,mode = <GSBI_PROT_I2C_UART>;
|
|
};
|
|
|
|
&gsbi4_serial {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&uart0_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&gsbi5 {
|
|
status = "okay";
|
|
qcom,mode = <GSBI_PROT_SPI>;
|
|
|
|
spi@1a280000 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&spi_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
SBL1@0 {
|
|
label = "SBL1";
|
|
reg = <0x0 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
MIBIB@10000 {
|
|
label = "MIBIB";
|
|
reg = <0x10000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
SBL2@30000 {
|
|
label = "SBL2";
|
|
reg = <0x30000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
SBL3@60000 {
|
|
label = "SBL3";
|
|
reg = <0x60000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
DDRCONFIG@90000 {
|
|
label = "DDRCONFIG";
|
|
reg = <0x90000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
SSD@a0000 {
|
|
label = "SSD";
|
|
reg = <0xa0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
TZ@b0000 {
|
|
label = "TZ";
|
|
reg = <0xb0000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
RPM@e0000 {
|
|
label = "RPM";
|
|
reg = <0xe0000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
APPSBL@100000 {
|
|
label = "APPSBL";
|
|
reg = <0x100000 0x70000>;
|
|
read-only;
|
|
};
|
|
|
|
APPSBLENV@170000 {
|
|
label = "APPSBLENV";
|
|
reg = <0x170000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
ART: ART@180000 {
|
|
label = "ART";
|
|
reg = <0x180000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
BOOTCONFIG@1c0000 {
|
|
label = "BOOTCONFIG";
|
|
reg = <0x1c0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
APPSBL_1@1d0000 {
|
|
label = "APPSBL_1";
|
|
reg = <0x1d0000 0x70000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&hs_phy_0 { /* USB3 port 0 HS phy */
|
|
status = "okay";
|
|
};
|
|
|
|
&ss_phy_0 { /* USB3 port 0 SS phy */
|
|
status = "okay";
|
|
};
|
|
|
|
&hs_phy_1 { /* USB3 port 1 HS phy */
|
|
status = "okay";
|
|
};
|
|
|
|
&ss_phy_1 { /* USB3 port 1 SS phy */
|
|
status = "okay";
|
|
};
|
|
|
|
&usb3_0 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&usb_pwr_en_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&usb3_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&dwc3_0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
hub_port0: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&dwc3_1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
hub_port1: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie1 {
|
|
status = "okay";
|
|
force_gen1 = <1>;
|
|
};
|
|
|
|
&qcom_pinmux {
|
|
button_pins: button_pins {
|
|
mux {
|
|
pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
|
|
"gpio58", "gpio64", "gpio65";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
led_pins: led_pins {
|
|
mux {
|
|
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
|
|
"gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
uart0_pins: uart0_pins {
|
|
mux {
|
|
pins = "gpio10", "gpio11";
|
|
function = "gsbi4";
|
|
drive-strength = <12>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
spi_pins: spi_pins {
|
|
mux {
|
|
pins = "gpio18", "gpio19", "gpio21";
|
|
function = "gsbi5";
|
|
bias-pull-down;
|
|
};
|
|
|
|
data {
|
|
pins = "gpio18", "gpio19";
|
|
drive-strength = <10>;
|
|
};
|
|
|
|
cs{
|
|
pins = "gpio20";
|
|
drive-strength = <10>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
clk {
|
|
pins = "gpio21";
|
|
drive-strength = <12>;
|
|
};
|
|
};
|
|
|
|
mdio0_pins: mdio0_pins {
|
|
mux {
|
|
pins = "gpio0", "gpio1";
|
|
function = "gpio";
|
|
drive-strength = <8>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
nand_pins: nand_pins {
|
|
mux {
|
|
pins = "gpio34", "gpio35", "gpio36",
|
|
"gpio37", "gpio38", "gpio39",
|
|
"gpio40", "gpio41", "gpio42",
|
|
"gpio43", "gpio44", "gpio45",
|
|
"gpio46", "gpio47";
|
|
function = "nand";
|
|
drive-strength = <10>;
|
|
bias-disable;
|
|
};
|
|
|
|
pullups {
|
|
pins = "gpio39";
|
|
bias-pull-up;
|
|
};
|
|
|
|
hold {
|
|
pins = "gpio40", "gpio41", "gpio42",
|
|
"gpio43", "gpio44", "gpio45",
|
|
"gpio46", "gpio47";
|
|
bias-bus-hold;
|
|
};
|
|
};
|
|
|
|
rgmii2_pins: rgmii2_pins {
|
|
mux {
|
|
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
|
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
|
function = "rgmii2";
|
|
drive-strength = <8>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
usb_pwr_en_pins: usb_pwr_en_pins {
|
|
mux{
|
|
pins = "gpio68";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
output-high;
|
|
};
|
|
};
|
|
}; |