Openwrt/openwrt/target/linux/x86-2.6/patches/100-scx200_hr_timer.patch
Felix Fietkau ee7fded0ad rename patch
SVN-Revision: 4951
2006-10-07 17:46:23 +00:00

321 lines
12 KiB
Diff

SCx200 High Resolution Timer Patch for Linux 2.6
http://www.gnusto.com/scx200-hr-timer.html
diff -Naurp linux-2.6.12-rc6.orig/arch/i386/Kconfig linux-2.6.12-rc6/arch/i386/Kconfig
--- linux-2.6.12-rc6.orig/arch/i386/Kconfig 2005-06-07 14:56:02.000000000 +0100
+++ linux-2.6.12-rc6/arch/i386/Kconfig 2005-06-07 16:43:19.000000000 +0100
@@ -458,6 +458,17 @@ config HPET_EMULATE_RTC
bool "Provide RTC interrupt"
depends on HPET_TIMER && RTC=y
+config SCx200HR_TIMER
+ bool "NatSemi SCx200 27MHz High-Resolution Timer Support"
+ help
+ Some of the AMD (formerly National Semiconductor) Geode
+ processors, notably the SC1100, suffer from a buggy time
+ stamp counter which causes them to lose time when the
+ processor is sleeping. Enable this option to use the
+ on-board 27Mz high-resolution timer to keep time instead.
+ depends on (SCx200)
+ default n
+
config SMP
bool "Symmetric multi-processing support"
---help---
diff -Naurp linux-2.6.12-rc6.orig/arch/i386/kernel/scx200.c linux-2.6.12-rc6/arch/i386/kernel/scx200.c
--- linux-2.6.12-rc6.orig/arch/i386/kernel/scx200.c 2005-06-07 14:56:02.000000000 +0100
+++ linux-2.6.12-rc6/arch/i386/kernel/scx200.c 2005-06-07 16:43:19.000000000 +0100
@@ -27,6 +27,10 @@ long scx200_gpio_shadow[2];
unsigned scx200_cb_base = 0;
+#ifdef CONFIG_SCx200HR_TIMER
+extern void __devinit scx200hr_timer_enable(void);
+#endif
+
static struct pci_device_id scx200_tbl[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SCx200_BRIDGE) },
{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_SC1100_BRIDGE) },
@@ -83,6 +87,9 @@ static int __devinit scx200_probe(struct
printk(KERN_INFO NAME ": Configuration Block base 0x%x\n", scx200_cb_base);
}
+#ifdef CONFIG_SCx200HR_TIMER
+ scx200hr_timer_enable();
+#endif
return 0;
}
diff -Naurp linux-2.6.12-rc6.orig/arch/i386/kernel/timers/Makefile linux-2.6.12-rc6/arch/i386/kernel/timers/Makefile
--- linux-2.6.12-rc6.orig/arch/i386/kernel/timers/Makefile 2004-03-11 18:21:13.000000000 +0000
+++ linux-2.6.12-rc6/arch/i386/kernel/timers/Makefile 2005-06-07 16:43:19.000000000 +0100
@@ -5,5 +5,6 @@
obj-y := timer.o timer_none.o timer_tsc.o timer_pit.o common.o
obj-$(CONFIG_X86_CYCLONE_TIMER) += timer_cyclone.o
+obj-$(CONFIG_SCx200HR_TIMER) += timer_scx200hr.o
obj-$(CONFIG_HPET_TIMER) += timer_hpet.o
obj-$(CONFIG_X86_PM_TIMER) += timer_pm.o
diff -Naurp linux-2.6.12-rc6.orig/arch/i386/kernel/timers/timer.c linux-2.6.12-rc6/arch/i386/kernel/timers/timer.c
--- linux-2.6.12-rc6.orig/arch/i386/kernel/timers/timer.c 2004-12-26 14:07:37.000000000 +0000
+++ linux-2.6.12-rc6/arch/i386/kernel/timers/timer.c 2005-06-07 16:43:19.000000000 +0100
@@ -13,6 +13,9 @@
#endif
/* list of timers, ordered by preference, NULL terminated */
static struct init_timer_opts* __initdata timers[] = {
+#ifdef CONFIG_SCx200HR_TIMER
+ &timer_scx200hr_init,
+#endif
#ifdef CONFIG_X86_CYCLONE_TIMER
&timer_cyclone_init,
#endif
diff -Naurp linux-2.6.12-rc6.orig/arch/i386/kernel/timers/timer_scx200hr.c linux-2.6.12-rc6/arch/i386/kernel/timers/timer_scx200hr.c
--- linux-2.6.12-rc6.orig/arch/i386/kernel/timers/timer_scx200hr.c 1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.12-rc6/arch/i386/kernel/timers/timer_scx200hr.c 2005-06-07 16:43:19.000000000 +0100
@@ -0,0 +1,220 @@
+/*
+ * Copyright (C) 2005 Ted Phelps
+ *
+ * This is a clock driver for the Geode SCx200's 27MHz high-resolution
+ * timer as the system clock replacing its buggy time stamp counter.
+ *
+ * Based on parts of timer_hpet.c, timer_tsc.c and timer_pit.c.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ */
+
+#include <asm/timer.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/seq_file.h>
+#include <linux/scx200.h>
+
+#define NAME "scx200hr"
+
+/* Read the clock */
+#define SCx200HR_CLOCK() inl(scx200_cb_base + SCx200_TIMER_OFFSET)
+
+/* High-resolution timer configuration address */
+#define SCx200_TMCNFG_OFFSET (SCx200_TIMER_OFFSET + 5)
+
+/* Set this bit to disable the 27 MHz input clock */
+#define HR_TM27MPD (1 << 2)
+
+/* Set this bit to update the count-up timer once per cycle of the
+ * 27MHz timer, clear it to update the timer once every 27 cycles
+ * (effectively producing a 1MHz counter) */
+#define HR_TMCLKSEL (1 << 1)
+
+/* Set this bit to enable the high-resolution timer interrupt */
+#define HR_TMEN (1 << 0)
+
+/* The frequency of the timer. Change this to 27000000 and set
+ * HR_TMCLKSEL in scx200hr_enable to run at the faster clock rate. At
+ * this point in time there is no point in doing so since times are
+ * recorded in usec except for the monotonic clock, which is only used
+ * by the hangcheck-timer. */
+#define HR_FREQ 1000000
+
+/* The number of cycles of the high-resolution timer we expect to see
+ * in a single tick. Note that the result is <<8 for greater precision*/
+#define HR_CYCLES_PER_TICK \
+ (SH_DIV(HR_FREQ / 1000000 * TICK_NSEC, 1000, 8))
+
+/* The number of cycles of the high-resolution timer we expect to see
+ * in one microsecond, <<8 */
+#define HR_CYCLES_PER_US ((HR_FREQ / 1000000) << 8)
+
+
+/* The value of the timer at the last interrupt */
+static u32 clock_at_last_interrupt;
+
+/* The number of high-resolution clock cycles beyond what we would
+ have expected that the last tick occurred, <<8 for greater precision */
+static long clock_delay;
+
+/* The total number of timer nanoseconds between the time the timer
+ * went live and the most recent tick. */
+static unsigned long long total_ns;
+
+/* A lock to guard access to the monotonic clock-related variables
+ * (total_ns and clocal_at_last_interrupt). Note that these are also
+ * protected by the xtime lock. */
+static seqlock_t hr_lock = SEQLOCK_UNLOCKED;
+
+/* Nonzero if the timer has been selected */
+static int enable_scx200hr;
+
+static int __init scx200hr_init(char *override)
+{
+ /* Watch for a command-line clock= override */
+ if (override[0] && strncmp(override, NAME, sizeof(NAME) - 1) != 0) {
+ return -ENODEV;
+ }
+
+ /* Note that we should try to enable this timer once the
+ * configuration block address is known */
+ printk(KERN_WARNING NAME ": timer not yet accessible; will probe later.\n");
+ enable_scx200hr = 1;
+ return -EAGAIN;
+}
+
+/* Called by the timer interrupt. The xtime_lock will be held. */
+static void mark_offset_scx200hr(void)
+{
+ u32 now, delta;
+
+ /* Avoid races between the interrupt handler and monotonic_clock */
+ write_seqlock(&hr_lock);
+
+ /* Determine how many cycles have elapsed since the last interrupt */
+ now = SCx200HR_CLOCK();
+ delta = (now - clock_at_last_interrupt) << 8;
+ clock_at_last_interrupt = now;
+
+ /* Update the total us count and remainder */
+ total_ns += (delta * 1000) / HR_CYCLES_PER_US;
+
+ /* The monotonic clock is safe now */
+ write_sequnlock(&hr_lock);
+
+ /* Adjust for interrupt handling delay */
+ delta += clock_delay;
+
+ /* The high-resolution timer is driven by a different crystal
+ * to the main CPU, so there's no guarantee that the 1KHz
+ * interrupt rate will coincide with the timer. This keeps
+ * the jiffies count in line with the high-resolution timer,
+ * which makes it possible for NTP to do its magic */
+ if (delta < HR_CYCLES_PER_TICK) {
+#if 1
+ /* Didn't go over 1000us: decrement jiffies to balance
+ * out increment in do_timer. This will cause some
+ * jitter if the frequency offset is large, as that
+ * adjustment will be applied about 1ms late. */
+ jiffies_64--;
+ clock_delay = delta;
+#else /* !1 */
+ clock_delay = 0;
+#endif /* 1 */
+ } else if (delta < (HR_CYCLES_PER_TICK << 1) + (HR_CYCLES_PER_TICK >> 1)) {
+ clock_delay = delta - HR_CYCLES_PER_TICK;
+ } else {
+ jiffies_64 += delta / HR_CYCLES_PER_TICK - 2;
+ clock_delay = HR_CYCLES_PER_TICK + delta % HR_CYCLES_PER_TICK;
+ }
+}
+
+/* Called by gettimeofday(). Returns the number of microseconds since
+ * the last interrupt. This is called with the xtime_lock held.*/
+static unsigned long get_offset_scx200hr(void)
+{
+ u32 delta;
+
+ /* Get the time now and determine how many cycles have
+ * transpired since the interrupt, adjusting for timer
+ * interrupt jitter. */
+ delta = ((SCx200HR_CLOCK() - clock_at_last_interrupt) << 8) + clock_delay;
+
+ /* Convert from cycles<<8 to microseconds */
+ return delta / HR_CYCLES_PER_US;
+}
+
+/* Returns the number of nanoseconds since the init of the timer. */
+static unsigned long long monotonic_clock_scx200hr(void)
+{
+ u32 delta, seq;
+ unsigned long long ns;
+
+ /* This function is *not* called with xtime_lock held, so we
+ * need to get the hr_lock to ensure we're not competing with
+ * mark_offset_scx200hr. */
+ do {
+ seq = read_seqbegin(&hr_lock);
+ ns = total_ns;
+ delta = SCx200HR_CLOCK() - clock_at_last_interrupt;
+ } while (read_seqretry(&hr_lock, seq));
+
+ /* Convert cycles to microseconds and add. */
+ return ns + delta * 1000 / HR_CYCLES_PER_US;
+}
+
+/* scx200hr timer_opts struct */
+struct timer_opts timer_scx200hr = {
+ .name = NAME,
+ .mark_offset = mark_offset_scx200hr,
+ .get_offset = get_offset_scx200hr,
+ .monotonic_clock = monotonic_clock_scx200hr,
+ .delay = NULL
+};
+
+/* And the init_timer struct */
+struct init_timer_opts __devinitdata timer_scx200hr_init = {
+ .init = scx200hr_init,
+ .opts = &timer_scx200hr
+};
+
+
+/* Switch from the original timer to the high-resolution timer */
+void __devinit scx200hr_timer_enable(void)
+{
+ /* Make sure the timer was requested and that the
+ * configuration block is present */
+ if (!enable_scx200hr || !scx200_cb_present()) {
+ return;
+ }
+
+ /* Reserve the timer region for ourselves */
+ if (!request_region(scx200_cb_base + SCx200_TIMER_OFFSET,
+ SCx200_TIMER_SIZE,
+ "NatSemi SCx200 High-Resolution Timer")) {
+ printk(KERN_WARNING NAME ": unable to lock timer region\n");
+ return;
+ }
+
+ /* Configure the timer */
+ outb(0, scx200_cb_base + SCx200_TMCNFG_OFFSET);
+
+ /* Record the current value of the timer. */
+ clock_at_last_interrupt = SCx200HR_CLOCK();
+
+ /* Get the current value of the monotonic clock */
+ total_ns = cur_timer->monotonic_clock();
+
+ /* Switch from the original timer functions to ours, but keep
+ * the current delay function since loops_per_jiffy will have
+ * been computed using that */
+ timer_scx200hr.delay = cur_timer->delay;
+ cur_timer = &timer_scx200hr;
+
+ printk(KERN_INFO "switching to scx200 high-resolution timer (%lu cpt)\n",
+ HR_CYCLES_PER_TICK);
+}
diff -Naurp linux-2.6.12-rc6.orig/include/asm-i386/timer.h linux-2.6.12-rc6/include/asm-i386/timer.h
--- linux-2.6.12-rc6.orig/include/asm-i386/timer.h 2005-06-07 14:56:11.000000000 +0100
+++ linux-2.6.12-rc6/include/asm-i386/timer.h 2005-06-07 16:43:19.000000000 +0100
@@ -50,6 +50,9 @@ extern struct init_timer_opts timer_tsc_
#ifdef CONFIG_X86_CYCLONE_TIMER
extern struct init_timer_opts timer_cyclone_init;
#endif
+#ifdef CONFIG_SCx200HR_TIMER
+extern struct init_timer_opts timer_scx200hr_init;
+#endif
extern unsigned long calibrate_tsc(void);
extern void init_cpu_khz(void);
diff -Naurp linux-2.6.12-rc6.orig/include/linux/scx200.h linux-2.6.12-rc6/include/linux/scx200.h
--- linux-2.6.12-rc6.orig/include/linux/scx200.h 2005-06-07 14:56:11.000000000 +0100
+++ linux-2.6.12-rc6/include/linux/scx200.h 2005-06-07 16:43:19.000000000 +0100
@@ -32,7 +32,7 @@ extern unsigned scx200_cb_base;
/* High Resolution Timer */
#define SCx200_TIMER_OFFSET 0x08
-#define SCx200_TIMER_SIZE 0x05
+#define SCx200_TIMER_SIZE 0x06
/* Clock Generators */
#define SCx200_CLOCKGEN_OFFSET 0x10