aafee2b3e9
The first gpio controller (gpio or gpio0) is always enabled by default in the SoC DTSI files. No need to set status=okay in the device DTS files a second time. Remove the redundant statements. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
109 lines
1.7 KiB
Plaintext
109 lines
1.7 KiB
Plaintext
#include "rt2880.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "airlink101,ar670w", "ralink,rt2880-soc";
|
|
model = "Airlink101 AR670W";
|
|
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
flash@bdc00000 {
|
|
compatible = "cfi-flash";
|
|
reg = <0xbc400000 0x800000>;
|
|
bank-width = <2>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x30000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@30000 {
|
|
reg = <0x30000 0x10000>;
|
|
label = "factory";
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
compatible = "lzma";
|
|
reg = <0x40000 0x3c0000>;
|
|
label = "firmware";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "green:power";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wpsblue {
|
|
label = "blue:wps";
|
|
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
gpio {
|
|
groups = "i2c", "spi", "uartlite";
|
|
function = "gpio";
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
mtd-mac-address = <&factory 0x2004>;
|
|
|
|
port@0 {
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
phy-mode = "mii";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
ralink,mtd-eeprom = <&factory 0x2000>;
|
|
};
|