Openwrt build for Asrock G10 Router
Go to file
Andy Lee c5235f6b24 ath79: add support for TP-Link TL-WR841HP v3
Specifications:
- QCA9533 SoC, 8 MB nor flash, 64 MB DDR2 RAM
- 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps
- 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100
- 1x WAN, LAN, Wifi, PWR, WPS, RE Leds
- Reset, Wifi on/off, WPS, RE buttons
- Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1

Label MAC addresses based on vendor firmware:
LAN      *:ea    label
WAN      *:eb    label +1
2.4 GHz  *:ea    label
The label MAC address in found in u-boot 0x1fc00

Installation:
Upload openwrt-ath79-generic-tplink_tl-wr841hp-v3-squashfs-factory.bin
from stock firmware webgui.
Maybe we need rename to shorten file name due to stock webgui error.

Revert back to stock firmware instructions:
- set your PC to static IP address 192.168.0.66 netmask 255.255.255.0
- download stock firmware from Tp-link website
- put it in the root directory of tftp server software
- rename it to wr841hpv3_tp_recovery.bin
- power on while pressing Reset button until any Led is lighting up
- wait for the router to reboot. done

Forum support topic:
https://forum.openwrt.org/t/support-for-tp-link-tl-wr841hp-v3-router

Signed-off-by: Andy Lee <congquynh284@yahoo.com>
[rebase and squash]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-13 23:30:05 +02:00
.github
config treewide: fix spelling 'seperate' -> 'separate' 2021-02-28 23:59:21 +00:00
include prereq-build: diff requirement to GNU 2021-06-12 15:54:13 -10:00
LICENSES
package odhcpd: update to latest git HEAD 2021-06-13 22:28:40 +02:00
scripts scripts/feeds: generate index after all feeds are updated 2021-06-07 12:44:50 -10:00
target ath79: add support for TP-Link TL-WR841HP v3 2021-06-13 23:30:05 +02:00
toolchain toolchain/gdb: fix broken non-python build 2021-06-09 13:16:45 +02:00
tools ramips: add support for TP-Link Archer C6 v3 2021-06-13 11:32:31 +02:00
.gitattributes
.gitignore gitignore: add .vscode for VS Code users 2021-03-08 10:46:06 +01:00
BSDmakefile
Config.in
COPYING
feeds.conf.default feeds: management: remove dead and out of project feed 2021-05-01 00:37:15 +02:00
Makefile Revert "build: replace which with Bash command built-in" 2021-03-03 22:51:39 +01:00
README.md README: switch from freenode to oftc 2021-06-12 12:39:35 -10:00
rules.mk build: add ninja build tool and make it available for cmake 2021-06-12 10:46:39 +02:00

OpenWrt logo

OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.

Sunshine!

Development

To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.

Requirements

You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.

binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.6+ rsync subversion unzip which

Quickstart

  1. Run ./scripts/feeds update -a to obtain all the latest package definitions defined in feeds.conf / feeds.conf.default

  2. Run ./scripts/feeds install -a to install symlinks for all obtained packages into package/feeds/

  3. Run make menuconfig to select your preferred configuration for the toolchain, target system & firmware packages.

  4. Run make to build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.

The main repository uses multiple sub-repositories to manage packages of different categories. All packages are installed via the OpenWrt package manager called opkg. If you're looking to develop the web interface or port packages to OpenWrt, please find the fitting repository below.

Support Information

For a list of supported devices see the OpenWrt Hardware Database

Documentation

Support Community

  • Forum: For usage, projects, discussions and hardware advise.
  • Support Chat: Channel #openwrt on oftc.net.

Developer Community

License

OpenWrt is licensed under GPL-2.0