3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
158 lines
2.5 KiB
Plaintext
158 lines
2.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca956x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "tplink,eap245-v3", "qca,qca9563";
|
|
model = "TP-Link EAP245 v3";
|
|
|
|
aliases {
|
|
led-boot = &led_status_green;
|
|
led-failsafe = &led_status_amber;
|
|
led-running = &led_status_green;
|
|
led-upgrade = &led_status_amber;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status_green: status_green {
|
|
label = "green:status";
|
|
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led_status_amber: status_amber {
|
|
label = "amber:status";
|
|
gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "factory-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot";
|
|
reg = <0x040000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "partition-table";
|
|
reg = <0x080000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
info: partition@90000 {
|
|
label = "info";
|
|
reg = <0x090000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@a0000 {
|
|
label = "art";
|
|
reg = <0x0a0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@b0000 {
|
|
label = "extra-para";
|
|
reg = <0x0b0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@c0000 {
|
|
compatible = "openwrt,elf";
|
|
label = "firmware";
|
|
reg = <0x0c0000 0xe40000>;
|
|
};
|
|
|
|
partition@f00000 {
|
|
label = "config";
|
|
reg = <0xf00000 0x030000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@f30000 {
|
|
label = "mutil-log";
|
|
reg = <0xf30000 0x080000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fb0000 {
|
|
label = "oops";
|
|
reg = <0xfb0000 0x040000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy-mask = <0x1>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "sgmii";
|
|
qca,ar8327-initvals = <
|
|
0x04 0x00080080 /* PAD0 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
0xe0 0xc74164de /* SGMII_CTRL */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "sgmii";
|
|
|
|
mtd-mac-address = <&info 0x8>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&info 0x8>;
|
|
};
|