3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
213 lines
3.5 KiB
Plaintext
213 lines
3.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_power_green;
|
|
led-failsafe = &led_power_amber;
|
|
led-running = &led_power_green;
|
|
led-upgrade = &led_power_amber;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
led_spi {
|
|
compatible = "spi-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
sck-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
|
|
mosi-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
|
num-chipselects = <0>;
|
|
|
|
led_gpio: led_gpio@0 {
|
|
compatible = "nxp,74lvc594";
|
|
reg = <0>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
registers-number = <1>;
|
|
spi-max-frequency = <500000>;
|
|
|
|
gpio_latch_bit {
|
|
gpio-hog;
|
|
gpios = <4 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
line-name = "gpio-latch-bit";
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power_green: power_green {
|
|
label = "green:power";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_power_amber: power_amber {
|
|
label = "amber:power";
|
|
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
left_blue {
|
|
label = "blue:left";
|
|
gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
right_blue {
|
|
label = "blue:right";
|
|
gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wps_green {
|
|
label = "green:wps";
|
|
gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
client_red {
|
|
label = "red:client";
|
|
gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
client_green {
|
|
label = "green:client";
|
|
gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
router_red {
|
|
label = "red:router";
|
|
gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
router_green {
|
|
label = "green:router";
|
|
gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "WPS button";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
extender_apmode {
|
|
label = "EXTENDER/APMODE switch";
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
linux,input-type = <EV_SW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
clocks = <&extosc>;
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
caldata: partition@50000 {
|
|
label = "caldata";
|
|
reg = <0x050000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "caldata-backup";
|
|
reg = <0x060000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@70000 {
|
|
label = "config";
|
|
reg = <0x070000 0x010000>;
|
|
};
|
|
|
|
partition@80000 {
|
|
label = "pot";
|
|
reg = <0x080000 0x010000>;
|
|
};
|
|
|
|
partition@90000 {
|
|
label = "firmware";
|
|
reg = <0x090000 0xf30000>;
|
|
compatible = "denx,uimage";
|
|
};
|
|
|
|
partition@fc0000 {
|
|
label = "language";
|
|
reg = <0xfc0000 0x040000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&caldata 0x1000>;
|
|
mtd-mac-address = <&caldata 0x06>;
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&caldata 0x00>;
|
|
|
|
phy-handle = <&phy4>;
|
|
phy-mode = "rgmii-rxid";
|
|
|
|
pll-data = <0x86000000 0x80000101 0x80001313>;
|
|
};
|