3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
116 lines
1.8 KiB
Plaintext
116 lines
1.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wps {
|
|
label = "blue:wps";
|
|
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
network {
|
|
label = "blue:network";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan2g {
|
|
label = "blue:wlan2";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
wlan5g {
|
|
label = "blue:wlan5";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
watchdog {
|
|
compatible = "linux,wdt-gpio";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
hw_algo = "toggle";
|
|
hw_margin_ms = <500>;
|
|
always-running;
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
switch0@1f {
|
|
compatible = "qca,ar8327";
|
|
reg = <0x1f>;
|
|
qca,ar8327-initvals = <
|
|
0x04 0x87600000 /* PORT0 PAD MODE CTRL */
|
|
0x0c 0x00080080 /* PORT6 PAD MODE CTRL */
|
|
0x10 0x81000080 /* POWER_ON_STRAP */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
0x94 0x0000007e /* PORT6 STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0xa6000000 0x00000101 0x00001616>;
|
|
mtd-mac-address = <&art 0x0>;
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x00000101 0x00001616>;
|
|
mtd-mac-address = <&art 0x6>;
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x18>;
|
|
};
|
|
|
|
// This node is required for the Ethernet ports to work correctly.
|
|
&gpio {
|
|
status = "okay";
|
|
};
|