64a6f4a9c1
ALFA Network Pi-WiFi4 is a Qualcomm QCA9531 v2 based, high-power 802.11n WiFi board in Raspberry Pi 3B shape, equipped with 1x FE and 4x USB 2.0. Specifications: - Qualcomm/Atheros QCA9531 v2 - 650/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16+ MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet - 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM - 2x IPEX/U.FL connectors on PCB - 4x USB 2.0 Type-A - Genesys Logic GL850G 4-port USB HUB - USB power is controlled by GPIO - 5x LED (3x on PCB, 2x in RJ45, 4x driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, enabled by default) - 1x micro USB Type-B for power and system console (Holtek HT42B534) - UART and GPIO (8-pin, 1.27 mm pitch) header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
88 lines
1.5 KiB
Plaintext
88 lines
1.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "qca9531_alfa-network_r36a.dtsi"
|
|
|
|
/ {
|
|
model = "ALFA Network Pi-WiFi4";
|
|
compatible = "alfa-network,pi-wifi4", "qca,qca9531";
|
|
|
|
aliases {
|
|
led-boot = &led_usb;
|
|
led-failsafe = &led_usb;
|
|
led-upgrade = &led_usb;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&enable_gpio4 &enable_gpio16>;
|
|
|
|
lan_data {
|
|
label = "orange:lan_data";
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan_link {
|
|
label = "green:lan_link";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_usb: usb {
|
|
label = "green:usb";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "usbport";
|
|
trigger-sources = <&gl850g_port1>, <&gl850g_port2>,
|
|
<&gl850g_port3>, <&gl850g_port4>;
|
|
};
|
|
|
|
wlan {
|
|
label = "blue:wlan";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
mtd-mac-address = <&art 0x1002>;
|
|
mtd-mac-address-increment = <(-1)>;
|
|
};
|
|
|
|
ð1 {
|
|
compatible = "syscon", "simple-mfd";
|
|
};
|
|
|
|
&gpio_export {
|
|
usb-power {
|
|
gpio-export,name = "usb-power";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
&hub_port0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
gl850g_port1: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
|
|
gl850g_port2: port@2 {
|
|
reg = <2>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
|
|
gl850g_port3: port@3 {
|
|
reg = <3>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
|
|
gl850g_port4: port@4 {
|
|
reg = <4>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|