3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
153 lines
2.5 KiB
Plaintext
153 lines
2.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar7241.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "tplink,tl-wr842n-v1", "qca,ar7241";
|
|
model = "TP-Link TL-WR842N/ND v1";
|
|
|
|
aliases {
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
label-mac-device = &ath9k;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
rfkill {
|
|
label = "rfkill";
|
|
linux,code = <KEY_RFKILL>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_system: system {
|
|
label = "green:system";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
qss {
|
|
label = "green:qss";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led3g {
|
|
label = "green:3g";
|
|
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
|
|
trigger-sources = <&hub_port>;
|
|
linux,default-trigger = "usbport";
|
|
};
|
|
};
|
|
|
|
ath9k-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan {
|
|
label = "green:wlan";
|
|
gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
};
|
|
|
|
gpio-export {
|
|
compatible = "gpio-export";
|
|
|
|
gpio_usb_power {
|
|
gpio-export,name = "tp-link:power:usb";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
hub_port: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
reg = <0x0 0x20000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "tplink,firmware";
|
|
reg = <0x20000 0x7d0000>;
|
|
label = "firmware";
|
|
};
|
|
|
|
partition@7f0000 {
|
|
reg = <0x7f0000 0x10000>;
|
|
label = "art";
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
ath9k: wifi@0,0 {
|
|
compatible = "pci168c,002e";
|
|
reg = <0x0000 0 0 0 0>;
|
|
#gpio-cells = <2>;
|
|
gpio-controller;
|
|
qca,no-eeprom;
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
mtd-mac-address-increment = <(-1)>;
|
|
};
|
|
|
|
ð1 {
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
mtd-mac-address-increment = <1>;
|
|
};
|