Openwrt build for Asrock G10 Router
bba6646b5c
This patch adds support for the COMFAST CF-E313AC, an outdoor wireless CPE with two Ethernet ports and a 802.11ac radio. Specifications: - QCA9531 SoC - 650/400/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps WAN Ethernet, 48V PoE-in - 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out - 1x manual pass-through PoE switch - 64 MB RAM (DDR2) - 16 MB FLASH - QCA9886 2T2R 5 GHz 802.11ac, 23 dBm - 12 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new one, so a factory reset will be needed. To do so, once the new firmware is flashed, enter into failsafe mode by pressing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing faster. Once in failsafe mode, perform a factory reset as usual. Alternatively, the U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The device's LEDs will blink several times and the recovery page will be at http://192.168.1.1; use it to upload the sysupgrade image. Note: Four MAC addresses are stored in the "art" partition (read-only): - 0x0000: 40:A5:EF:AA:AA:A0 - 0x0006: 40:A5:EF:AA:AA:A2 - 0x1002: 40:A5:EF:AA:AA:A1 - 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data) The stock firmware assigns MAC addresses to physical and virtual interfaces in a very particular way: - eth0 corresponds to the physical Ethernet port labeled as WAN - eth1 corresponds to the physical Ethernet port labeled as LAN - eth0 belongs to the bridge interface br-wan - eth1 belongs to the bridge interface br-lan - eth0 is assigned the MAC from 0x0 (*:A0) - eth1 is assigned the MAC from 0x1002 (*:A1) - br-wan is forced to use the MAC from 0x1002 (*:A1) - br-lan is forced to use the MAC from 0x0 (*:A0) - radio0 uses the calibration data from 0x5000 (which contains a valid MAC address, *:A3). However, it is overwritten by the one at 0x6 (*:A2) This commit preserves the LAN/WAN roles of the physical Ethernet ports (as labeled on the router) and the MAC addresses they expose by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position of the eth0/eth1 compared to the stock firmware: - eth0 corresponds to the physical Ethernet port labeled as LAN - eth1 corresponds to the physical Ethernet port labeled as WAN - eth0 belongs to the bridge interface br-lan - eth1 is the interface at @wan - eth0 is assigned the MAC from 0x0 (*:A0) - eth1 is assigned the MAC from 0x1002 (*:A1) - br-lan inherits the MAC from eth0 (*:A0) - @wan inherits the MAC from eth1 (*:A1) - radio0's MAC is overwritten to the one at 0x6 This way, eth0/eth1's positions differ from the stock firmware, but the weird MAC ressignations in br-lan/br-wan are avoided while the external behaviour of the router is maintained. Additionally, WAN port is connected to the PHY gmac, allowing to monitor the link status (e.g., to restart DHCP negotiation when plugging a cable). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> |
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| feeds.conf.default | ||
| LICENSE | ||
| Makefile | ||
| README | ||
| rules.mk | ||
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python3.5+, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org