Openwrt/target/linux/kirkwood/patches-5.4/001-ARM-dts-kirkwood-Add-Check-Point-L-50-board.patch
Pawel Dembicki 67ce9aedd6 kirkwood: add support for Check Point L-50
This patch adds support for the Check Point L-50 from 600/1100 series
routers.

Specification:
-CPU: Marvell Kirkwood 88F6281 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL

Known issues:
-DSL not supported
-Expresscard not tested

Installation:

Step one -> backup:
make backup u-boot and env for revert stock posibility
make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr

Step two -> Use kwboot tool to upload openwrt u-boot to RAM:

run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t"
end start u-boot

Step three -> Restore macs (e.g. below):
setenv eth1addr 00:1C:XX:XX:XX:6C
setenv ethaddr 00:1C:XX:XX:XX:6B
setenv lan1_mac_addr 00:1C:XX:XX:XX:6C
setenv lan2_mac_addr 00:1C:XX:XX:XX:6D
setenv lan3_mac_addr 00:1C:XX:XX:XX:6E
setenv lan4_mac_addr 00:1C:XX:XX:XX:6F
setenv lan5_mac_addr 00:1C:XX:XX:XX:70
setenv lan6_mac_addr 00:1C:XX:XX:XX:71
setenv lan7_mac_addr 00:1C:XX:XX:XX:72
setenv lan8_mac_addr 00:1C:XX:XX:XX:73
setenv dmz_mac_addr 00:1C:XX:XX:XX:74
setenv dsl_mac_addr 00:1C:XX:XX:XX:75

Step four -> flash u-boot:
mw 0x0800000 0xffff 0x100000
nand erase 0x0 100000
tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb
nand write 0x0800000 0x0 0x100000
saveenv

Step five -> run initramfs image:

tftpboot 0x02000000 openwrt.bin; bootm 0x02000000;

Step six -> install sysupgrade OpenWrt image:

copy to /tmp/ sysupgrade image
run sysupgrade

Back to stock:
Restore original u-boot end env.
Install factory image via stock u-boot.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-11 13:33:28 +02:00

486 lines
8.9 KiB
Diff

From efa968c18abab78c5e0c40a853caf286c3629a59 Mon Sep 17 00:00:00 2001
From: Pawel Dembicki <paweldembicki@gmail.com>
Date: Tue, 17 Mar 2020 21:28:01 +0100
Subject: [PATCH v3] ARM: dts: kirkwood: Add Check Point L-50 board
This patch adds dts for the Check Point L-50 from 600/1100 series
routers.
Specification:
-CPU: Marvell Kirkwood 88F6821 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+3))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
---
Changes in v3:
- fix typo and code style issues pointed by OpenWrt guys
Changes in v2:
- none
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/kirkwood-l-50.dts | 438 ++++++++++++++++++++++++++++
2 files changed, 439 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-l-50.dts
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -270,6 +270,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-iomega_ix2_200.dtb \
kirkwood-is2.dtb \
kirkwood-km_kirkwood.dtb \
+ kirkwood-l-50.dtb \
kirkwood-laplug.dtb \
kirkwood-linkstation-lsqvl.dtb \
kirkwood-linkstation-lsvl.dtb \
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-l-50.dts
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Check Point L-50 Board Description
+ * Copyright 2020 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Check Point L-50";
+ compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>;
+ pinctrl-names = "default";
+
+ pmx_sysrst: pmx-sysrst {
+ marvell,pins = "mpp6";
+ marvell,function = "sysrst";
+ };
+
+ pmx_button29: pmx_button29 {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_led38: pmx_led38 {
+ marvell,pins = "mpp38";
+ marvell,function = "gpio";
+ };
+
+ pmx_sdio_cd: pmx-sdio-cd {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ };
+
+ serial@12000 {
+ status = "okay";
+ };
+
+ mvsdio@90000 {
+ status = "okay";
+ cd-gpios = <&gpio1 14 9>;
+ };
+
+ i2c@11000 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ gpio2: gpio-expander@20{
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ compatible = "semtech,sx1505q";
+ reg = <0x20>;
+
+ gpio-controller;
+ };
+
+ /* Three GPIOs from 0x21 exp. are undescribed in dts:
+ * 1: DSL module reset (active low)
+ * 5: mPCIE reset (active low)
+ * 6: Express card reset (active low)
+ */
+ gpio3: gpio-expander@21{
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ compatible = "semtech,sx1505q";
+ reg = <0x21>;
+
+ gpio-controller;
+ };
+
+ rtc@30 {
+ compatible = "s35390a";
+ reg = <0x30>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status_green {
+ label = "l-50:green:status";
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ };
+
+ status_red {
+ label = "l-50:red:status";
+ gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi {
+ label = "l-50:green:wifi";
+ gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ internet_green {
+ label = "l-50:green:internet";
+ gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+ };
+
+ internet_red {
+ label = "l-50:red:internet";
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ };
+
+ usb1_green {
+ label = "l-50:green:usb1";
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&hub_port3>;
+ };
+
+ usb1_red {
+ label = "l-50:red:usb1";
+ gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+ };
+
+ usb2_green {
+ label = "l-50:green:usb2";
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&hub_port1>;
+ };
+
+ usb2_red {
+ label = "l-50:red:usb2";
+ gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ usb2_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "usb2_pwr";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
+ regulator-always-on;
+ };
+
+ usb1_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1_pwr";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 4 GPIO_ACTIVE_LOW>;
+ regulator-always-on;
+ };
+
+ mpcie_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "mpcie_pwr";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ express_card_pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "express_card_pwr";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ factory_defaults {
+ label = "factory_defaults";
+ gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy8: ethernet-phy@8 {
+ reg = <0x08>;
+ };
+
+ switch0: switch@10 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10>;
+ dsa,member = <0 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan5";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan6";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan2";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan7";
+ };
+
+ switch0port5: port@5 {
+ reg = <5>;
+ phy-mode = "rgmii-txid";
+ link = <&switch1port5>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ phy-mode = "rgmii-id";
+ ethernet = <&eth1port>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+
+ switch@11 {
+ compatible = "marvell,mv88e6085";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x11>;
+ dsa,member = <0 1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan3";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan8";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan4";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "dmz";
+ };
+
+ switch1port5: port@5 {
+ reg = <5>;
+ phy-mode = "rgmii-txid";
+ link = <&switch0port5>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "dsl";
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+ };
+ };
+};
+
+&eth0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <&ethphy8>;
+ };
+};
+
+&eth1 {
+ status = "okay";
+ ethernet1-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x00000000 0x000c0000>;
+ };
+
+ partition@a0000 {
+ label = "bootldr-env";
+ reg = <0x000c0000 0x00040000>;
+ };
+
+ partition@100000 {
+ label = "kernel-1";
+ reg = <0x00100000 0x00800000>;
+ };
+
+ partition@900000 {
+ label = "rootfs-1";
+ reg = <0x00900000 0x07100000>;
+ };
+
+ partition@7a00000 {
+ label = "kernel-2";
+ reg = <0x07a00000 0x00800000>;
+ };
+
+ partition@8200000 {
+ label = "rootfs-2";
+ reg = <0x08200000 0x07100000>;
+ };
+
+ partition@f300000 {
+ label = "default_sw";
+ reg = <0x0f300000 0x07900000>;
+ };
+
+ partition@16c00000 {
+ label = "logs";
+ reg = <0x16c00000 0x01800000>;
+ };
+
+ partition@18400000 {
+ label = "preset_cfg";
+ reg = <0x18400000 0x00100000>;
+ };
+
+ partition@18500000 {
+ label = "adsl";
+ reg = <0x18500000 0x00100000>;
+ };
+
+ partition@18600000 {
+ label = "storage";
+ reg = <0x18600000 0x07a00000>;
+ };
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&sata_phy0 {
+ status = "disabled";
+};
+
+&sata_phy1 {
+ status = "disabled";
+};
+
+&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ #trigger-source-cells = <0>;
+
+ hub_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ hub_port3: port@3 {
+ reg = <3>;
+ #trigger-source-cells = <0>;
+ };
+ };
+};