c8190713cb
A minority of ethernet-phy definitions seems to use numbers in label, name and reg property relatively random. This patch aligns their use to have the same numeric value for all of them. While at it, improve order of properties/add newlines for the ethX nodes where necessary. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
176 lines
2.8 KiB
Plaintext
176 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca9557.dtsi"
|
|
|
|
/ {
|
|
model = "TP-Link RE350K v1";
|
|
compatible = "tplink,re350k-v1", "qca,qca9558";
|
|
|
|
aliases {
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
mdio-gpio0 = &mdio2;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8";
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
app-config {
|
|
label = "app-config";
|
|
linux,code = <BTN_0>;
|
|
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
led {
|
|
label = "led";
|
|
linux,code = <BTN_1>;
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "tp-link:green:power";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan2g_green {
|
|
label = "tp-link:green:wlan2g";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
wlan2g_red {
|
|
label = "tp-link:red:wlan2g";
|
|
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan5g_green {
|
|
label = "tp-link:green:wlan5g";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
wlan5g_red {
|
|
label = "tp-link:red:wlan5g";
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
mdio2: mdio {
|
|
compatible = "virtual,mdio-gpio";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>,
|
|
<&gpio 18 GPIO_ACTIVE_HIGH>;
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
|
|
phy-mode = "rgmii-rxid";
|
|
eee-broken-100tx;
|
|
eee-broken-1000t;
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&phy4>;
|
|
pll-data = <0x9e000000 0x80000101 0x80001313>;
|
|
|
|
mtd-mac-address = <&config 0x10008>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
rxdv-delay = <2>;
|
|
rxd-delay = <2>;
|
|
txen-delay = <0>;
|
|
txd-delay = <0>;
|
|
rgmii-enabled = <1>;
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "tplink,firmware";
|
|
label = "firmware";
|
|
reg = <0x020000 0xd70000>;
|
|
};
|
|
|
|
config: partition@d90000 {
|
|
label = "config";
|
|
reg = <0xd90000 0x260000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&config 0x10008>;
|
|
};
|