29ca10e537
The target uses 5.4 as default kernel since 04/2020. Kernel 4.19 support is not really maintained anymore, and there has been a lot of changes between 4.19 and 5.4 on this target. Despite, new devices are typically added for 5.4 only anyway. Thus, make maintaining of old stuff and reviewing of new stuff easier by removing support for kernel 4.19. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
164 lines
2.2 KiB
Plaintext
164 lines
2.2 KiB
Plaintext
#include "qcom-ipq8064-v1.0.dtsi"
|
|
|
|
/ {
|
|
model = "Qualcomm IPQ8064/DB149";
|
|
compatible = "qcom,ipq8064-db149", "qcom,ipq8064";
|
|
|
|
aliases {
|
|
serial0 = &gsbi2_serial;
|
|
};
|
|
|
|
reserved-memory {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
rsvd@41200000 {
|
|
reg = <0x41200000 0x300000>;
|
|
no-map;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qcom_pinmux {
|
|
rgmii0_pins: rgmii0_pins {
|
|
mux {
|
|
pins = "gpio2", "gpio66";
|
|
drive-strength = <8>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gsbi2 {
|
|
qcom,mode = <GSBI_PROT_I2C_UART>;
|
|
status = "okay";
|
|
|
|
gsbi2_serial: serial@12490000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&gsbi4 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&gsbi4_serial {
|
|
status = "disabled";
|
|
};
|
|
|
|
&flash {
|
|
m25p,fast-read;
|
|
|
|
partition@0 {
|
|
label = "lowlevel_init";
|
|
reg = <0x0 0x1b0000>;
|
|
};
|
|
|
|
partition@1 {
|
|
label = "u-boot";
|
|
reg = <0x1b0000 0x80000>;
|
|
};
|
|
|
|
partition@2 {
|
|
label = "u-boot-env";
|
|
reg = <0x230000 0x40000>;
|
|
};
|
|
|
|
partition@3 {
|
|
label = "caldata";
|
|
reg = <0x270000 0x40000>;
|
|
};
|
|
|
|
partition@4 {
|
|
label = "firmware";
|
|
reg = <0x2b0000 0x1d50000>;
|
|
};
|
|
};
|
|
|
|
&usb3_0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb3_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&mdio0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
qca,ar8327-initvals = <
|
|
0x00004 0x7600000 /* PAD0_MODE */
|
|
0x00008 0x1000000 /* PAD5_MODE */
|
|
0x0000c 0x80 /* PAD6_MODE */
|
|
0x000e4 0x6a545 /* MAC_POWER_SEL */
|
|
0x000e0 0xc74164de /* SGMII_CTRL */
|
|
0x0007c 0x4e /* PORT0_STATUS */
|
|
0x00094 0x4e /* PORT6_STATUS */
|
|
>;
|
|
};
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
};
|
|
|
|
phy6: ethernet-phy@6 {
|
|
reg = <6>;
|
|
};
|
|
|
|
phy7: ethernet-phy@7 {
|
|
reg = <7>;
|
|
};
|
|
};
|
|
|
|
&gmac0 {
|
|
status = "okay";
|
|
phy-mode = "rgmii";
|
|
qcom,id = <0>;
|
|
phy-handle = <&phy4>;
|
|
|
|
pinctrl-0 = <&rgmii0_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&gmac1 {
|
|
status = "okay";
|
|
phy-mode = "sgmii";
|
|
qcom,id = <1>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&gmac2 {
|
|
status = "okay";
|
|
phy-mode = "sgmii";
|
|
qcom,id = <2>;
|
|
phy-handle = <&phy6>;
|
|
};
|
|
|
|
&gmac3 {
|
|
status = "okay";
|
|
phy-mode = "sgmii";
|
|
qcom,id = <3>;
|
|
phy-handle = <&phy7>;
|
|
};
|