01a1e21863
The only difference between the "openwrt,okli" and the generic parser is the magic. Set this in device tree for all affected devices and remove the "openwrt,okli" parser. Tested-by: Michael Pratt <mcpratt@protonmail.com> # EAP300 v2, ENS202EXT and ENH202 Signed-off-by: Bjørn Mork <bjorn@mork.no>
182 lines
2.9 KiB
Plaintext
182 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9341.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/mtd/partitions/uimage.h>
|
|
|
|
/ {
|
|
model = "Engenius ENS202EXT v1";
|
|
compatible = "engenius,ens202ext-v1", "qca,ar9341";
|
|
|
|
aliases {
|
|
serial0 = &uart;
|
|
led-boot = &led_power;
|
|
led-failsafe = &led_power;
|
|
led-running = &led_power;
|
|
led-upgrade = &led_power;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_power: power {
|
|
label = "amber:power";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan {
|
|
label = "amber:wlan";
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
rssilow {
|
|
label = "red:rssilow";
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssimedium {
|
|
label = "amber:rssimedium";
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
rssihigh {
|
|
label = "green:rssihigh";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
virtual_flash {
|
|
compatible = "mtd-concat";
|
|
|
|
devices = <&fwconcat0 &fwconcat1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
openwrt,ih-magic = <IH_MAGIC_OKLI>;
|
|
label = "firmware";
|
|
reg = <0x0 0x0>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "custom";
|
|
reg = <0x050000 0x050000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@a0000 {
|
|
label = "loader";
|
|
reg = <0x0a0000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
fwconcat1: partition@b0000 {
|
|
label = "fwconcat1";
|
|
reg = <0x0b0000 0x170000>;
|
|
};
|
|
|
|
partition@220000 {
|
|
label = "fakeroot";
|
|
reg = <0x220000 0x010000>;
|
|
read-only;
|
|
};
|
|
|
|
fwconcat0: partition@230000 {
|
|
label = "fwconcat0";
|
|
reg = <0x230000 0xbc0000>;
|
|
};
|
|
|
|
partition@df0000 {
|
|
label = "failsafe";
|
|
reg = <0xdf0000 0x200000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
phy-handle = <&swphy0>;
|
|
|
|
mtd-mac-address = <&art 0x0>;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
switch-phy-swap = <1>;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|