0d23fd2ab2
>From the Documentation/devicetree/bindings/leds/common.txt: - default-state : The initial state of the LED. Valid values are "on", "off", and "keep". If the LED is already on or off and the default-state property is set the to same value, then no glitch should be produced where the LED momentarily turns off (or on). The "keep" setting will keep the LED at whatever its current state is, without producing a glitch. The default is off if this property is not present. So setting the default-state of the LEDs to `off` is redundant as `off` is default LED state anyway. We should remove it as almost every new PR/patch submission contains this property by default which seems to be just copy&paste from some DTS file already present in the tree. Signed-off-by: Petr Štetiar <ynezz@true.cz>
142 lines
2.2 KiB
Plaintext
142 lines
2.2 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9344.dtsi"
|
|
|
|
/ {
|
|
compatible = "iodata,etg3-r", "qca,ar9344";
|
|
model = "I-O DATA ETG3-R";
|
|
|
|
aliases {
|
|
led-boot = &power;
|
|
led-failsafe = &power;
|
|
led-running = &power;
|
|
led-upgrade = &power;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
power: power {
|
|
label = "etg3-r:green:power";
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
notification {
|
|
label = "etg3-r:green:notification";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
&spi {
|
|
num-cs = <1>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@50000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x050000 0x780000>;
|
|
};
|
|
|
|
partition@7d0000 {
|
|
label = "Config";
|
|
reg = <0x07d0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@7e0000 {
|
|
label = "Rsv";
|
|
reg = <0x07e0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@7f0000 {
|
|
label = "ART";
|
|
reg = <0x7f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "rgmii";
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x07600000 /* PORT0 PAD MODE CTRL */
|
|
0x50 0xffb7ffb7 /* LED_CTRL0 */
|
|
0x54 0xffb7ffb7 /* LED_CTRL1 */
|
|
0x58 0xffb7ffb7 /* LED_CTRL2 */
|
|
0x5c 0x03ffff00 /* LED_CTRL3 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x0e000000 0x00000101 0x00001616>;
|
|
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
rgmii-gmac0 = <1>;
|
|
rxd-delay = <3>;
|
|
rxdv-delay = <3>;
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|