635f111148
In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
124 lines
2.0 KiB
Plaintext
124 lines
2.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
/ {
|
|
compatible = "tplink,tl-wr941n-v7-cn", "qca,qca9558";
|
|
model = "TP-Link TL-WR941N v7 (CN)";
|
|
|
|
aliases {
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_system: system {
|
|
label = "tp-link:green:system";
|
|
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
wlan {
|
|
label = "tp-link:green:wlan";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
qss {
|
|
label = "tp-link:green:qss";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wps {
|
|
label = "qss";
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x020000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "tplink,firmware";
|
|
label = "firmware";
|
|
reg = <0x020000 0x3d0000>;
|
|
};
|
|
|
|
art: partition@7f0000 {
|
|
label = "art";
|
|
reg = <0x3f0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
switch0@1f {
|
|
compatible = "qca,ar8236";
|
|
reg = <0x1f>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
phy-mode = "mii";
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
fixed-link {
|
|
speed = <100>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
};
|