Openwrt/target/linux/ath79/dts/qca9558_trendnet_tew-823dru.dts

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "qca955x.dtsi"

/ {
	compatible = "trendnet,tew-823dru", "qca,qca9558";
	model = "TRENDNET TEW-823DRU";

	aliases {
		led-boot = &led_power_green;
		led-failsafe = &led_power_green;
		led-running = &led_power_green;
		led-upgrade = &led_power_green;
	};

	leds {
		compatible = "gpio-leds";

		power_orange {
			label = "trendnet:orange:power";
			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
		};

		led_power_green: power_green {
			label = "trendnet:green:power";
			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
		};

		planet_green {
			label = "trendnet:green:planet";
			gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
		};

		planet_orange {
			label = "trendnet:orange:planet";
			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
		};
	};

	keys {
		compatible = "gpio-keys";

		reset {
			label = "Reset button";
			linux,code = <KEY_RESTART>;
			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
			debounce-interval = <60>;
		};

		wps {
			label = "WPS button";
			linux,code = <KEY_WPS_BUTTON>;
			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
			debounce-interval = <60>;
		};
	};
};

&pcie0 {
	status = "okay";
};

&pcie1 {
	status = "okay";
};

&uart {
	status = "okay";
};

&usb_phy0 {
	status = "okay";
};

&usb0 {
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";

	hub_port0: port@1 {
		reg = <1>;
		#trigger-source-cells = <0>;
	};
};

&usb_phy1 {
	status = "okay";
};

&usb1 {
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";

	hub_port1: port@1 {
		reg = <1>;
		#trigger-source-cells = <0>;
	};
};

&spi {
	status = "okay";

	num-cs = <1>;

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <25000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "u-boot";
				reg = <0x000000 0x030000>;
				read-only;
			};

			partition@30000 {
				label = "nvram";
				reg = <0x030000 0x010000>;
				read-only;
			};

			partition@40000 {
				compatible = "denx,uimage";
				label = "firmware";
				reg = <0x040000 0xef0000>;
			};

			partition@f30000 {
				label = "lang";
				reg = <0xf30000 0x030000>;
				read-only;
			};

			partition@f60000 {
				label = "my-dlink";
				reg = <0xf60000 0x080000>;
				read-only;
			};

			partition@fe0000 {
				label = "mac";
				reg = <0xfe0000 0x010000>;
				read-only;
			};

			art: partition@ff0000 {
				label = "art";
				reg = <0xff0000 0x010000>;
				read-only;
			};
		};
	};
};

&mdio0 {
	status = "okay";

	phy0: ethernet-phy@0 {
		reg = <0>;
		qca,ar8327-initvals = <
			0x04 0x00080080 /* PORT0 PAD MODE CTRL */
			0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
			0x10 0x81000080 /* POWER_ON_STRAP */
			0x7c 0x0000007e /* PORT0_STATUS */
			0x94 0x0000007e /* PORT6 STATUS */
		>;
	};
};

&eth0 {
	status = "okay";

	phy-handle = <&phy0>;
	pll-data = <0x56000000 0x00000101 0x00001616>;

	gmac-config {
		device = <&gmac>;
		rgmii-enabled = <1>;
	};
};

&eth1 {
	status = "okay";

	pll-data = <0x03000101 0x00000101 0x00001616>;

	fixed-link {
		speed = <1000>;
		full-duplex;
	};
};

&wmac {
	status = "okay";

	mtd-cal-data = <&art 0x1000>;
};