411ad3727a
It's wrong set the mux to bias-disable. The best way to do this is by creating a separate group and disable the specific pins. By documentation, any subgroup with no bias definition is ignored so the mux definition is useless. Rework the definition by sremoving the mux subgroup and set the remaining subgroup with the mux function and drive-strength Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
520 lines
8.9 KiB
Plaintext
520 lines
8.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
#include "qcom-ipq8064-v2.0.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "Buffalo WXR-2533DHP";
|
|
compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
|
|
|
|
memory@42000000 {
|
|
reg = <0x42000000 0x1e000000>;
|
|
device_type = "memory";
|
|
};
|
|
|
|
reserved-memory {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
rsvd@41200000 {
|
|
reg = <0x41200000 0x300000>;
|
|
no-map;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
serial0 = &gsbi4_serial;
|
|
|
|
led-boot = &power;
|
|
led-failsafe = &diag;
|
|
led-running = &power;
|
|
led-upgrade = &power;
|
|
};
|
|
|
|
chosen {
|
|
/* use "ubi_rootfs" volume in "ubi" partition as rootfs */
|
|
bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
soc {
|
|
nand@1ac00000 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&nand_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
cs@0 {
|
|
reg = <0>;
|
|
compatible = "qcom,nandcs";
|
|
|
|
nand-ecc-strength = <4>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-step-size = <512>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
ubi@0 {
|
|
label = "ubi";
|
|
reg = <0x0000000 0x4000000>;
|
|
};
|
|
|
|
rootfs_1@4000000 {
|
|
label = "rootfs_1";
|
|
reg = <0x4000000 0x4000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
mdio {
|
|
compatible = "virtual,mdio-gpio";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
|
|
<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-0 = <&mdio0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
ethernet-phy@0 {
|
|
reg = <0>;
|
|
qca,ar8327-initvals = <
|
|
0x00004 0x07600000 /* PAD0_MODE */
|
|
0x00008 0x01000000 /* PAD5_MODE */
|
|
0x0000c 0x00000080 /* PAD6_MODE */
|
|
0x00050 0xcc35cc35 /* LED_CTRL0 */
|
|
0x00054 0xca35ca35 /* LED_CTRL1 */
|
|
0x00058 0xc935c935 /* LED_CTRL2 */
|
|
0x0005c 0x03ffff00 /* LED_CTRL3 */
|
|
0x000e4 0x0006a545 /* MAC_POWER_SEL */
|
|
0x000e0 0xc74164de /* SGMII_CTRL */
|
|
0x0007c 0x0000007e /* PORT0_STATUS */
|
|
0x00094 0x0000007e /* PORT6_STATUS */
|
|
>;
|
|
};
|
|
|
|
ethernet-phy@4 {
|
|
reg = <4>;
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-0 = <&led_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
usb {
|
|
label = "wxr-2533dhp:green:usb";
|
|
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "usbport";
|
|
trigger-sources = <&hub_port0 &hub_port1>;
|
|
};
|
|
|
|
guestport {
|
|
label = "wxr-2533dhp:green:guestport";
|
|
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
diag: diag {
|
|
label = "wxr-2533dhp:orange:diag";
|
|
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
internet_orange {
|
|
label = "wxr-2533dhp:orange:internet";
|
|
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
internet_white {
|
|
label = "wxr-2533dhp:white:internet";
|
|
gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wireless_orange {
|
|
label = "wxr-2533dhp:orange:wireless";
|
|
gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
wireless_white {
|
|
label = "wxr-2533dhp:white:wireless";
|
|
gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
router_orange {
|
|
label = "wxr-2533dhp:orange:router";
|
|
gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
router_white {
|
|
label = "wxr-2533dhp:white:router";
|
|
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
power: power {
|
|
label = "wxr-2533dhp:white:power";
|
|
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
pinctrl-0 = <&button_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
power {
|
|
label = "power";
|
|
gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_POWER>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
|
|
eject {
|
|
label = "eject";
|
|
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_EJECTCD>;
|
|
};
|
|
|
|
guest {
|
|
label = "guest";
|
|
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
};
|
|
|
|
ap {
|
|
label = "ap";
|
|
gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
router {
|
|
label = "router";
|
|
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
|
|
auto {
|
|
label = "auto";
|
|
gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
linux,input-type = <EV_SW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&adm_dma {
|
|
status = "okay";
|
|
};
|
|
|
|
&gmac1 {
|
|
status = "okay";
|
|
|
|
phy-mode = "rgmii";
|
|
qcom,id = <1>;
|
|
|
|
pinctrl-0 = <&rgmii2_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
mtd-mac-address = <&ART 6>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&gmac2 {
|
|
status = "okay";
|
|
|
|
phy-mode = "sgmii";
|
|
qcom,id = <2>;
|
|
|
|
mtd-mac-address = <&ART 0>;
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&gsbi4 {
|
|
status = "okay";
|
|
qcom,mode = <GSBI_PROT_I2C_UART>;
|
|
};
|
|
|
|
&gsbi4_serial {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&uart0_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&gsbi5 {
|
|
status = "okay";
|
|
qcom,mode = <GSBI_PROT_SPI>;
|
|
|
|
spi@1a280000 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&spi_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <50000000>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
SBL1@0 {
|
|
label = "SBL1";
|
|
reg = <0x0 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
MIBIB@10000 {
|
|
label = "MIBIB";
|
|
reg = <0x10000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
SBL2@30000 {
|
|
label = "SBL2";
|
|
reg = <0x30000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
SBL3@60000 {
|
|
label = "SBL3";
|
|
reg = <0x60000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
DDRCONFIG@90000 {
|
|
label = "DDRCONFIG";
|
|
reg = <0x90000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
SSD@a0000 {
|
|
label = "SSD";
|
|
reg = <0xa0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
TZ@b0000 {
|
|
label = "TZ";
|
|
reg = <0xb0000 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
RPM@e0000 {
|
|
label = "RPM";
|
|
reg = <0xe0000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
APPSBL@100000 {
|
|
label = "APPSBL";
|
|
reg = <0x100000 0x70000>;
|
|
read-only;
|
|
};
|
|
|
|
APPSBLENV@170000 {
|
|
label = "APPSBLENV";
|
|
reg = <0x170000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
ART: ART@180000 {
|
|
label = "ART";
|
|
reg = <0x180000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
BOOTCONFIG@1c0000 {
|
|
label = "BOOTCONFIG";
|
|
reg = <0x1c0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
APPSBL_1@1d0000 {
|
|
label = "APPSBL_1";
|
|
reg = <0x1d0000 0x70000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb3_0 {
|
|
status = "okay";
|
|
|
|
pinctrl-0 = <&usb_pwr_en_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&usb3_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&dwc3_0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
hub_port0: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&dwc3_1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
hub_port1: port@1 {
|
|
reg = <1>;
|
|
#trigger-source-cells = <0>;
|
|
};
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie1 {
|
|
status = "okay";
|
|
force_gen1 = <1>;
|
|
};
|
|
|
|
&qcom_pinmux {
|
|
button_pins: button_pins {
|
|
mux {
|
|
pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
|
|
"gpio58", "gpio64", "gpio65";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
led_pins: led_pins {
|
|
mux {
|
|
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
|
|
"gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
uart0_pins: uart0_pins {
|
|
mux {
|
|
pins = "gpio10", "gpio11";
|
|
function = "gsbi4";
|
|
drive-strength = <12>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
spi_pins: spi_pins {
|
|
mux {
|
|
pins = "gpio18", "gpio19", "gpio21";
|
|
function = "gsbi5";
|
|
bias-pull-down;
|
|
};
|
|
|
|
data {
|
|
pins = "gpio18", "gpio19";
|
|
drive-strength = <10>;
|
|
};
|
|
|
|
cs{
|
|
pins = "gpio20";
|
|
drive-strength = <10>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
clk {
|
|
pins = "gpio21";
|
|
drive-strength = <12>;
|
|
};
|
|
};
|
|
|
|
mdio0_pins: mdio0_pins {
|
|
mux {
|
|
pins = "gpio0", "gpio1";
|
|
function = "gpio";
|
|
drive-strength = <8>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
nand_pins: nand_pins {
|
|
disable {
|
|
pins = "gpio34", "gpio35", "gpio36",
|
|
"gpio37", "gpio38";
|
|
function = "nand";
|
|
drive-strength = <10>;
|
|
bias-disable;
|
|
};
|
|
|
|
pullups {
|
|
pins = "gpio39";
|
|
function = "nand";
|
|
drive-strength = <10>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
hold {
|
|
pins = "gpio40", "gpio41", "gpio42",
|
|
"gpio43", "gpio44", "gpio45",
|
|
"gpio46", "gpio47";
|
|
function = "nand";
|
|
drive-strength = <10>;
|
|
bias-bus-hold;
|
|
};
|
|
};
|
|
|
|
rgmii2_pins: rgmii2_pins {
|
|
mux {
|
|
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
|
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
|
function = "rgmii2";
|
|
drive-strength = <8>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
usb_pwr_en_pins: usb_pwr_en_pins {
|
|
mux{
|
|
pins = "gpio68";
|
|
function = "gpio";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
output-high;
|
|
};
|
|
};
|
|
}; |