e6d4744f9a
The WAN LED on DIR-810L was actually blinking on LAN1 port activity. This has already been improved for the TEW-810DR, where the GPIO has been set up explicitly rather than having it controlled by the switch. This patch also applies this setup to the DIR-810L. In addition, the trigger in 01_leds is set up with ucidef_set_led_switch for both devices now, so state changes should be displayed correctly as well. Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [DIR-810L] Tested-by: J. Scott Heppler <shep971@centurylink.net> [TEW-810DR]
125 lines
1.9 KiB
Plaintext
125 lines
1.9 KiB
Plaintext
//SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7620a.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory5g: partition@50000 {
|
|
label = "factory5g";
|
|
reg = <0x50000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "Wolf_Config";
|
|
reg = <0x60000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@70000 {
|
|
label = "MyDlink";
|
|
reg = <0x70000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@f0000 {
|
|
label = "Jffs2";
|
|
reg = <0xf0000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@170000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x170000 0x690000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0x28>;
|
|
|
|
mediatek,portmap = "llllw";
|
|
};
|
|
|
|
&gsw {
|
|
mediatek,port4 = "ephy";
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pa_pins>;
|
|
|
|
ralink,mtd-eeprom = <&factory 0x0>;
|
|
mtd-mac-address = <&factory 0x28>;
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
wifi@0,0 {
|
|
reg = <0x0000 0 0 0 0>;
|
|
mediatek,mtd-eeprom = <&factory 0x8000>;
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
mtd-mac-address = <&factory 0x28>;
|
|
mtd-mac-address-increment = <2>;
|
|
};
|
|
};
|