2ff9686040
Move local DTS files from "files-5.4" to "files" directory so kernel 5.10 can use it. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
136 lines
2.3 KiB
Plaintext
136 lines
2.3 KiB
Plaintext
/dts-v1/;
|
|
|
|
#include "kirkwood.dtsi"
|
|
#include "kirkwood-6281.dtsi"
|
|
|
|
/ {
|
|
model = "Seagate GoFlex Home";
|
|
compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
|
|
|
|
aliases {
|
|
led-boot = &led_health;
|
|
led-failsafe = &led_fault;
|
|
led-running = &led_health;
|
|
led-upgrade = &led_fault;
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x00000000 0x8000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
|
|
stdout-path = &uart0;
|
|
};
|
|
|
|
ocp@f1000000 {
|
|
pinctrl: pin-controller@10000 {
|
|
pmx_usb_power_enable: pmx-usb-power-enable {
|
|
marvell,pins = "mpp29";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
pmx_led_white: pmx-led-white {
|
|
marvell,pins = "mpp40";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
pmx_led_green: pmx-led_green {
|
|
marvell,pins = "mpp46";
|
|
marvell,function = "gpio";
|
|
};
|
|
|
|
pmx_led_orange: pmx-led-orange {
|
|
marvell,pins = "mpp47";
|
|
marvell,function = "gpio";
|
|
};
|
|
};
|
|
|
|
serial@12000 {
|
|
status = "okay";
|
|
};
|
|
|
|
sata@80000 {
|
|
status = "okay";
|
|
nr-ports = <2>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_health: health {
|
|
label = "status:green:health";
|
|
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
|
default-state = "on";
|
|
};
|
|
|
|
led_fault: fault {
|
|
label = "status:orange:fault";
|
|
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
misc {
|
|
label = "status:white:misc";
|
|
gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "disk-activity";
|
|
};
|
|
};
|
|
|
|
regulators {
|
|
compatible = "simple-bus";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pinctrl-0 = <&pmx_usb_power_enable>;
|
|
pinctrl-names = "default";
|
|
|
|
usb_power: regulator@1 {
|
|
compatible = "regulator-fixed";
|
|
reg = <1>;
|
|
regulator-name = "USB Power";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&nand {
|
|
status = "okay";
|
|
|
|
chip-delay = <40>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0000000 0x0100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@100000 {
|
|
label = "ubi";
|
|
reg = <0x0100000 0xff00000>;
|
|
};
|
|
};
|
|
|
|
&mdio {
|
|
status = "okay";
|
|
|
|
ethphy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
ethernet0-port@0 {
|
|
phy-handle = <ðphy0>;
|
|
};
|
|
};
|