4cf3fd49fc
The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to indicate the current boot state. This patch adds support for such cases. The existing led sequences should be the same as before. Boards which are using a led different from power (like TDW89x0) are changed to switch of the led after boot Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48041
224 lines
3.6 KiB
Plaintext
224 lines
3.6 KiB
Plaintext
/dts-v1/;
|
|
|
|
/include/ "danube.dtsi"
|
|
|
|
/ {
|
|
model = "ARV7519PW - Astoria Networks";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
|
|
|
|
leds {
|
|
boot = &power;
|
|
failsafe = &power2;
|
|
running = &power;
|
|
|
|
dsl = &dsl;
|
|
internet = &online;
|
|
wifi = &wifi;
|
|
};
|
|
};
|
|
|
|
memory@0 {
|
|
reg = <0x0 0x4000000>;
|
|
};
|
|
|
|
sram@1F000000 {
|
|
vmmc@107000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
fpi@10000000 {
|
|
localbus@0 {
|
|
nor-boot@0 {
|
|
compatible = "lantiq,nor";
|
|
bank-width = <2>;
|
|
reg = <0 0x0 0x2000000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "uboot";
|
|
reg = <0x00000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "uboot_env";
|
|
reg = <0x40000 0x20000>;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "firmware";
|
|
reg = <0x60000 0xf80000>;
|
|
};
|
|
|
|
partition@fe0000 {
|
|
label = "board_config";
|
|
reg = <0xfe0000 0x20000>;
|
|
read-only;
|
|
};
|
|
};
|
|
|
|
mac_addr {
|
|
compatible = "lantiq,eth-mac";
|
|
reg = <0 0xfe0016 0x6>;
|
|
mac-increment = <2>;
|
|
};
|
|
};
|
|
|
|
gpio: pinmux@E100B10 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&state_default>;
|
|
|
|
state_default: pinmux {
|
|
ebu {
|
|
lantiq,groups = "ebu cs1";
|
|
lantiq,function = "ebu";
|
|
};
|
|
pci_in {
|
|
lantiq,groups = "req1";
|
|
lantiq,function = "pci";
|
|
lantiq,open-drain = <1>;
|
|
lantiq,pull = <2>;
|
|
lantiq,output = <0>;
|
|
};
|
|
pci_out {
|
|
lantiq,groups = "gnt1";
|
|
lantiq,function = "pci";
|
|
lantiq,pull = <0>;
|
|
lantiq,output = <1>;
|
|
};
|
|
pci_rst {
|
|
lantiq,pins = "io21";
|
|
lantiq,pull = <2>;
|
|
lantiq,output = <1>;
|
|
};
|
|
switch_rst {
|
|
lantiq,pins = "io19";
|
|
lantiq,pull = <2>;
|
|
lantiq,output = <1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
etop@E180000 {
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
/* warning: passive port
|
|
only works with active devices */
|
|
ifxhcd@E101000 {
|
|
status = "okay";
|
|
};
|
|
|
|
pci@E105400 {
|
|
status = "okay";
|
|
lantiq,external-clock;
|
|
gpio-reset = <&gpio 21 0>;
|
|
req-mask = <0xf>;
|
|
};
|
|
};
|
|
|
|
ralink_eep {
|
|
compatible = "ralink,eeprom";
|
|
ralink,eeprom = "RT2860.eeprom";
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <100>;
|
|
|
|
rfkill {
|
|
label = "rfkill";
|
|
gpios = <&gpio 11 1>;
|
|
linux,code = <0xf7>;
|
|
};
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio 28 1>;
|
|
linux,code = <0x198>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
power: power {
|
|
label = "power";
|
|
gpios = <&gpio 2 1>;
|
|
default-state = "keep";
|
|
};
|
|
power2: power2 {
|
|
label = "power2";
|
|
gpios = <&gpio 14 1>;
|
|
};
|
|
online: online {
|
|
label = "online";
|
|
gpios = <&gpio 3 1>;
|
|
};
|
|
online2 {
|
|
label = "online2";
|
|
gpios = <&gpio 30 1>;
|
|
};
|
|
wifi: wifi {
|
|
label = "wifi";
|
|
gpios = <&gpio 12 1>;
|
|
};
|
|
wifi2 {
|
|
label = "wifi2";
|
|
gpios = <&gpio 10 1>;
|
|
};
|
|
wifi3 {
|
|
label = "wifi3";
|
|
gpios = <&gpio 6 1>;
|
|
};
|
|
voice {
|
|
label = "voice";
|
|
gpios = <&gpio 31 1>;
|
|
};
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio 15 1>;
|
|
};
|
|
wps2 {
|
|
label = "wps2";
|
|
gpios = <&gpio 7 1>;
|
|
};
|
|
wps3 {
|
|
label = "wps3";
|
|
gpios = <&gpio 23 1>;
|
|
};
|
|
dsl: dsl {
|
|
label = "dsl";
|
|
gpios = <&gpio 4 1>;
|
|
};
|
|
lan {
|
|
label = "lan";
|
|
gpios = <&gpio 1 1>;
|
|
};
|
|
tv {
|
|
label = "tv";
|
|
gpios = <&gpio 20 1>;
|
|
};
|
|
upgrade {
|
|
label = "upgrade";
|
|
gpios = <&gpio 29 1>;
|
|
};
|
|
};
|
|
|
|
/* is there another way to "reserve" the GPIO? */
|
|
gpio_export {
|
|
compatible = "gpio-export";
|
|
#size-cells = <0>;
|
|
|
|
switch {
|
|
gpio-export,name = "switch";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio 19 0>;
|
|
};
|
|
};
|
|
};
|