Openwrt/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts
Sungbo Eo 16965a0f3f kirkwood: convert DTS patches into plain DTS files
Move DTS files newly created by patch files to files directory. This will make
these files much more maintainable.

Patching the kernel Makefile is unnecessary, as the DTS files specified in
DEVICE_DTS will be compiled by OpenWrt buildroot anyway.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-27 12:38:21 +01:00

125 lines
2.3 KiB
Plaintext

/dts-v1/;
#include "kirkwood.dtsi"
#include "kirkwood-6281.dtsi"
/ {
model = "Seagate GoFlex Home";
compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
aliases {
led-boot = &led_health;
led-failsafe = &led_fault;
led-running = &led_health;
led-upgrade = &led_fault;
};
memory {
device_type = "memory";
reg = <0x00000000 0x8000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
stdout-path = &uart0;
};
ocp@f1000000 {
pinctrl: pin-controller@10000 {
pmx_usb_power_enable: pmx-usb-power-enable {
marvell,pins = "mpp29";
marvell,function = "gpio";
};
pmx_led_white: pmx-led-white {
marvell,pins = "mpp40";
marvell,function = "gpio";
};
pmx_led_green: pmx-led_green {
marvell,pins = "mpp46";
marvell,function = "gpio";
};
pmx_led_orange: pmx-led-orange {
marvell,pins = "mpp47";
marvell,function = "gpio";
};
};
serial@12000 {
status = "ok";
};
sata@80000 {
status = "okay";
nr-ports = <2>;
};
};
gpio-leds {
compatible = "gpio-leds";
led_health: health {
label = "status:green:health";
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
default-state = "on";
};
led_fault: fault {
label = "status:orange:fault";
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
};
misc {
label = "status:white:misc";
gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
linux,default-trigger = "disk-activity";
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&pmx_usb_power_enable>;
pinctrl-names = "default";
usb_power: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
regulator-name = "USB Power";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
regulator-always-on;
regulator-boot-on;
gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
};
};
};
&nand {
chip-delay = <40>;
status = "okay";
partition@0 {
label = "u-boot";
reg = <0x0000000 0x100000>;
read-only;
};
partition@100000 {
label = "ubi";
reg = <0x100000 0x0ff00000>;
};
};
&mdio {
status = "okay";
ethphy0: ethernet-phy@0 {
reg = <0>;
};
};
&eth0 {
status = "okay";
ethernet0-port@0 {
phy-handle = <&ethphy0>;
};
};