eb531337a7
This adds support for the TP-Link TL-WR710N v2.1. It is basically a re-issue of the v1.2. Specifications: SoC: Atheros AR9331 CPU: 400 MHz Flash: 8 MiB RAM: 32 MiB WiFi: 2.4 GHz b/g/n Ethernet: 2x 100M ports USB: 1x 2.0 The only difference from the v1 is the TP-Link hardware ID/revision. Attention: The TL-WR710N v2.0 (!) has only 4 MB flash and cannot be flashed with this image. It has a different TPLINK_HWREV, so accidental flashing of the factory image should be impossible without additional measures. Unfortunately, the v2.0 in ar71xx has the same board name, so sysupgrade from ar71xx v2.0 into ath79 v1/v2.1 will not be prevented, but will brick the device. Flashing instruction: Upload the factory image via the OEM firmware GUI upgrade mechanism. Further notes: To make implementation easier if somebody desires to port the 4M v2.0, this already creates two DTSI files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Fabian Eppig <fabian@eppig.de>
89 lines
1.4 KiB
Plaintext
89 lines
1.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9331.dtsi"
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &uart;
|
|
led-boot = &led_system;
|
|
led-failsafe = &led_system;
|
|
led-running = &led_system;
|
|
led-upgrade = &led_system;
|
|
label-mac-device = ð0;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_system: system {
|
|
label = "tl-wr710n:green:system";
|
|
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
reg_usb_vbus: regulator {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "usb_vbus";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5000000>;
|
|
gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <0>;
|
|
switch-phy-swap = <0>;
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
mtd-mac-address-increment = <(-1)>;
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
status = "okay";
|
|
|
|
dr_mode = "host";
|
|
vbus-supply = <®_usb_vbus>;
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&uboot 0x1fc00>;
|
|
};
|