Openwrt build for Asrock G10 Router
3a3d998c12
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.
0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"
Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
µUSB 2.0 (debugging & power input)
2x 3.5mm jack for microphone & headphone (SGTL5000)
Arduino Shield expansion with I2C, SPI, UART, and GPIO
JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)
Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.
Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.
As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
|
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| feeds.conf.default | ||
| LICENSE | ||
| Makefile | ||
| README | ||
| rules.mk | ||
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python3.5+, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org