cc5194cf03
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader is a hacked u-Boot that reads an LZMA image directly, so we skip generating the uImage header and enable the lzma mtdsplit parser. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 43153
104 lines
1.5 KiB
Plaintext
104 lines
1.5 KiB
Plaintext
/dts-v1/;
|
|
|
|
/include/ "rt2880.dtsi"
|
|
|
|
/ {
|
|
compatible = "AR670W", "ralink,rt2880-soc";
|
|
model = "Airlink101 AR670W";
|
|
|
|
palmbus@300000 {
|
|
gpio0: gpio@600 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "i2c", "spi", "uartlite";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
ethernet@400000 {
|
|
status = "okay";
|
|
mtd-mac-address = <&factory 0x2004>;
|
|
|
|
port@0 {
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
phy0: ethernet-phy@0 {
|
|
phy-mode = "mii";
|
|
reg = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
wmac@480000 {
|
|
status = "okay";
|
|
ralink,mtd-eeprom = <&factory 0x2000>;
|
|
};
|
|
|
|
cfi@bdc00000 {
|
|
compatible = "cfi-flash";
|
|
reg = <0xbc400000 0x800000>;
|
|
|
|
bank-width = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
u-boot@0 {
|
|
reg = <0x0 0x30000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
factory: factory@30000 {
|
|
reg = <0x30000 0x10000>;
|
|
label = "factory";
|
|
read-only;
|
|
};
|
|
|
|
firmware@40000 {
|
|
reg = <0x40000 0x3c0000>;
|
|
label = "firmware";
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
status {
|
|
label = "ar670w:green:power";
|
|
gpios = <&gpio0 7 1>;
|
|
};
|
|
|
|
wpsblue {
|
|
label = "ar670w:blue:wps";
|
|
gpios = <&gpio0 13 1>;
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <100>;
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio0 0 1>;
|
|
linux,code = <0x211>;
|
|
};
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 9 1>;
|
|
linux,code = <0x198>;
|
|
};
|
|
};
|
|
};
|