b201818044
Early printk was disabled because it caused hangs on some devices, the old patches were using the CFE console now we use the normal serial console, it is at a constant address. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 38309
152 lines
3.9 KiB
Diff
152 lines
3.9 KiB
Diff
commit 808fe9c2fa81a6b3e20fe813d5410e7fd6606efa
|
|
Author: Hauke Mehrtens <hauke@hauke-m.de>
|
|
Date: Sun Jul 18 15:11:26 2010 +0200
|
|
|
|
MIPS: BCM47XX: Remove CFE support
|
|
|
|
bcm47xx only uses the CFE code for early print to a console, but that
|
|
is also possible with a early print serial 8250 driver.
|
|
|
|
The CFE api init causes hangs somewhere in prom_init_cfe() on some
|
|
devices like the Buffalo WHR-HP-G54 and the Asus WL-520GU.
|
|
This was reported in https://dev.openwrt.org/ticket/4061 and
|
|
https://forum.openwrt.org/viewtopic.php?id=17063
|
|
|
|
This will remove all the CFE handling code from bcm47xx.
|
|
|
|
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
--- a/arch/mips/Kconfig
|
|
+++ b/arch/mips/Kconfig
|
|
@@ -112,13 +112,11 @@ config BCM47XX
|
|
select CEVT_R4K
|
|
select CSRC_R4K
|
|
select DMA_NONCOHERENT
|
|
- select FW_CFE
|
|
select HW_HAS_PCI
|
|
select IRQ_CPU
|
|
select NO_EXCEPT_FILL
|
|
select SYS_SUPPORTS_32BIT_KERNEL
|
|
select SYS_SUPPORTS_LITTLE_ENDIAN
|
|
- select SYS_HAS_EARLY_PRINTK
|
|
help
|
|
Support for BCM47XX based boards
|
|
|
|
--- a/arch/mips/bcm47xx/prom.c
|
|
+++ b/arch/mips/bcm47xx/prom.c
|
|
@@ -30,12 +30,9 @@
|
|
#include <linux/spinlock.h>
|
|
#include <linux/smp.h>
|
|
#include <asm/bootinfo.h>
|
|
-#include <asm/fw/cfe/cfe_api.h>
|
|
-#include <asm/fw/cfe/cfe_error.h>
|
|
#include <bcm47xx.h>
|
|
#include <bcm47xx_board.h>
|
|
|
|
-static int cfe_cons_handle;
|
|
|
|
static char bcm47xx_system_type[20] = "Broadcom BCM47XX";
|
|
|
|
@@ -52,91 +49,6 @@ __init void bcm47xx_set_system_type(u16
|
|
chip_id);
|
|
}
|
|
|
|
-void prom_putchar(char c)
|
|
-{
|
|
- while (cfe_write(cfe_cons_handle, &c, 1) == 0)
|
|
- ;
|
|
-}
|
|
-
|
|
-static __init void prom_init_cfe(void)
|
|
-{
|
|
- uint32_t cfe_ept;
|
|
- uint32_t cfe_handle;
|
|
- uint32_t cfe_eptseal;
|
|
- int argc = fw_arg0;
|
|
- char **envp = (char **) fw_arg2;
|
|
- int *prom_vec = (int *) fw_arg3;
|
|
-
|
|
- /*
|
|
- * Check if a loader was used; if NOT, the 4 arguments are
|
|
- * what CFE gives us (handle, 0, EPT and EPTSEAL)
|
|
- */
|
|
- if (argc < 0) {
|
|
- cfe_handle = (uint32_t)argc;
|
|
- cfe_ept = (uint32_t)envp;
|
|
- cfe_eptseal = (uint32_t)prom_vec;
|
|
- } else {
|
|
- if ((int)prom_vec < 0) {
|
|
- /*
|
|
- * Old loader; all it gives us is the handle,
|
|
- * so use the "known" entrypoint and assume
|
|
- * the seal.
|
|
- */
|
|
- cfe_handle = (uint32_t)prom_vec;
|
|
- cfe_ept = 0xBFC00500;
|
|
- cfe_eptseal = CFE_EPTSEAL;
|
|
- } else {
|
|
- /*
|
|
- * Newer loaders bundle the handle/ept/eptseal
|
|
- * Note: prom_vec is in the loader's useg
|
|
- * which is still alive in the TLB.
|
|
- */
|
|
- cfe_handle = prom_vec[0];
|
|
- cfe_ept = prom_vec[2];
|
|
- cfe_eptseal = prom_vec[3];
|
|
- }
|
|
- }
|
|
-
|
|
- if (cfe_eptseal != CFE_EPTSEAL) {
|
|
- /* too early for panic to do any good */
|
|
- printk(KERN_ERR "CFE's entrypoint seal doesn't match.");
|
|
- while (1) ;
|
|
- }
|
|
-
|
|
- cfe_init(cfe_handle, cfe_ept);
|
|
-}
|
|
-
|
|
-static __init void prom_init_console(void)
|
|
-{
|
|
- /* Initialize CFE console */
|
|
- cfe_cons_handle = cfe_getstdhandle(CFE_STDHANDLE_CONSOLE);
|
|
-}
|
|
-
|
|
-static __init void prom_init_cmdline(void)
|
|
-{
|
|
- static char buf[COMMAND_LINE_SIZE] __initdata;
|
|
-
|
|
- /* Get the kernel command line from CFE */
|
|
- if (cfe_getenv("LINUX_CMDLINE", buf, COMMAND_LINE_SIZE) >= 0) {
|
|
- buf[COMMAND_LINE_SIZE - 1] = 0;
|
|
- strcpy(arcs_cmdline, buf);
|
|
- }
|
|
-
|
|
- /* Force a console handover by adding a console= argument if needed,
|
|
- * as CFE is not available anymore later in the boot process. */
|
|
- if ((strstr(arcs_cmdline, "console=")) == NULL) {
|
|
- /* Try to read the default serial port used by CFE */
|
|
- if ((cfe_getenv("BOOT_CONSOLE", buf, COMMAND_LINE_SIZE) < 0)
|
|
- || (strncmp("uart", buf, 4)))
|
|
- /* Default to uart0 */
|
|
- strcpy(buf, "uart0");
|
|
-
|
|
- /* Compute the new command line */
|
|
- snprintf(arcs_cmdline, COMMAND_LINE_SIZE, "%s console=ttyS%c,115200",
|
|
- arcs_cmdline, buf[4]);
|
|
- }
|
|
-}
|
|
-
|
|
static __init void prom_init_mem(void)
|
|
{
|
|
unsigned long mem;
|
|
@@ -184,9 +96,6 @@ static __init void prom_init_mem(void)
|
|
|
|
void __init prom_init(void)
|
|
{
|
|
- prom_init_cfe();
|
|
- prom_init_console();
|
|
- prom_init_cmdline();
|
|
prom_init_mem();
|
|
}
|
|
|