Openwrt/target/linux/brcm47xx/patches-3.0/0032-USB-Add-driver-for-the-bcma-bus.patch

From 7151c34627b938486008cfab25bfb4e4f730a021 Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sat, 26 Nov 2011 21:33:41 +0100
Subject: [PATCH 19/21] USB: Add driver for the bcma bus

This adds a USB driver using the generic platform device driver for the
USB controller found on the Broadcom bcma bus. The bcma bus just
exposes one device which serves the OHCI and the EHCI controller at the
same time. This driver probes for this USB controller and creates and
registers two new platform devices which will be probed by the new
generic platform device driver. This makes it possible to use the EHCI
and the OCHI controller on the bcma bus at the same time.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
---
 drivers/usb/host/Kconfig    |   12 ++
 drivers/usb/host/Makefile   |    1 +
 drivers/usb/host/bcma-hcd.c |  350 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 363 insertions(+), 0 deletions(-)
 create mode 100644 drivers/usb/host/bcma-hcd.c

--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -598,3 +598,15 @@ config USB_OCTEON_OHCI
 config USB_OCTEON2_COMMON
 	bool
 	default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI
+
+config USB_HCD_BCMA
+	tristate "BCMA usb host driver"
+	depends on BCMA && EXPERIMENTAL
+	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
+	select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
+	help
+	  Enbale support for the EHCI and OCHI host controller on an bcma bus.
+	  It converts the bcma driver into two platform device drivers
+	  for ehci and ohci.
+
+	  If unsure, say N.
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -35,3 +35,4 @@ obj-$(CONFIG_USB_HWA_HCD)	+= hwa-hc.o
 obj-$(CONFIG_USB_IMX21_HCD)	+= imx21-hcd.o
 obj-$(CONFIG_USB_FSL_MPH_DR_OF)	+= fsl-mph-dr-of.o
 obj-$(CONFIG_USB_OCTEON2_COMMON) += octeon2-common.o
+obj-$(CONFIG_USB_HCD_BCMA)	+= bcma-hcd.o
--- /dev/null
+++ b/drivers/usb/host/bcma-hcd.c
@@ -0,0 +1,298 @@
+/*
+ * Broadcom specific Advanced Microcontroller Bus
+ * Broadcom USB-core driver (BCMA bus glue)
+ *
+ * Copyright 2011 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Based on ssb-ohci driver
+ * Copyright 2007 Michael Buesch <m@bues.ch>
+ *
+ * Derived from the OHCI-PCI driver
+ * Copyright 1999 Roman Weissgaerber
+ * Copyright 2000-2002 David Brownell
+ * Copyright 1999 Linus Torvalds
+ * Copyright 1999 Gregory P. Smith
+ *
+ * Derived from the USBcore related parts of Broadcom-SB
+ * Copyright 2005-2011 Broadcom Corporation
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+#include <linux/bcma/bcma.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+
+MODULE_AUTHOR("Hauke Mehrtens");
+MODULE_DESCRIPTION("Common USB driver for BCMA Bus");
+MODULE_LICENSE("GPL");
+
+#define BCMA_CORE_SIZE		0x1000
+
+struct bcma_hcd_device {
+	struct platform_device *ehci_dev;
+	struct platform_device *ohci_dev;
+};
+
+/* based on arch/mips/brcm-boards/bcm947xx/pcibios.c */
+static void bcma_hcd_init_chip(struct bcma_device *dev)
+{
+	u32 tmp;
+
+	/*
+	 * USB 2.0 special considerations:
+	 *
+	 * 1. Since the core supports both OHCI and EHCI functions, it must
+	 *    only be reset once.
+	 *
+	 * 2. In addition to the standard SI reset sequence, the Host Control
+	 *    Register must be programmed to bring the USB core and various
+	 *    phy components out of reset.
+	 */
+	if (!bcma_core_is_enabled(dev)) {
+		bcma_core_enable(dev, 0);
+		mdelay(10);
+		if (dev->id.rev >= 5) {
+			/* Enable Misc PLL */
+			tmp = bcma_read32(dev, 0x1e0);
+			tmp |= 0x100;
+			bcma_write32(dev, 0x1e0, tmp);
+			if (bcma_wait_bits(dev, 0x1e0, 1 << 24, 100, 0))
+				printk(KERN_EMERG "Failed to enable misc PPL!\n");
+
+			/* Take out of resets */
+			bcma_write32(dev, 0x200, 0x4ff);
+			udelay(25);
+			bcma_write32(dev, 0x200, 0x6ff);
+			udelay(25);
+
+			/* Make sure digital and AFE are locked in USB PHY */
+			bcma_write32(dev, 0x524, 0x6b);
+			udelay(50);
+			tmp = bcma_read32(dev, 0x524);
+			udelay(50);
+			bcma_write32(dev, 0x524, 0xab);
+			udelay(50);
+			tmp = bcma_read32(dev, 0x524);
+			udelay(50);
+			bcma_write32(dev, 0x524, 0x2b);
+			udelay(50);
+			tmp = bcma_read32(dev, 0x524);
+			udelay(50);
+			bcma_write32(dev, 0x524, 0x10ab);
+			udelay(50);
+			tmp = bcma_read32(dev, 0x524);
+
+			if (bcma_wait_bits(dev, 0x528, 0xc000, 10000, 1))
+				printk(KERN_EMERG
+				       "USB20H mdio_rddata 0x%08x\n", tmp);
+
+			bcma_write32(dev, 0x528, 0x80000000);
+			tmp = bcma_read32(dev, 0x314);
+			udelay(265);
+			bcma_write32(dev, 0x200, 0x7ff);
+			udelay(10);
+
+			/* Take USB and HSIC out of non-driving modes */
+			bcma_write32(dev, 0x510, 0);
+		} else {
+			bcma_write32(dev, 0x200, 0x7ff);
+
+			udelay(1);
+		}
+	}
+#ifdef CONFIG_BCMA_DRIVER_MIPS
+	/* Work around for 4716 failures. */
+	if (dev->bus->chipinfo.id == 0x4716) {
+		u32 clk_freq;
+
+		clk_freq = bcma_cpu_clock(&dev->bus->drv_mips);
+		if (clk_freq >= 480000000)
+			tmp = 0x1846b; /* set CDR to 0x11(fast) */
+		else if (clk_freq == 453000000)
+			tmp = 0x1046b; /* set CDR to 0x10(slow) */
+		else
+			tmp = 0;
+
+		/* Change Shim mdio control reg to fix host not acking at
+		 * high frequencies
+		 */
+		if (tmp) {
+			bcma_write32(dev, 0x524, 0x1); /* write sel to enable */
+			udelay(500);
+
+			bcma_write32(dev, 0x524, tmp);
+			udelay(500);
+			bcma_write32(dev, 0x524, 0x4ab);
+			udelay(500);
+			tmp = bcma_read32(dev, 0x528);
+			bcma_write32(dev, 0x528, 0x80000000);
+		}
+	}
+#endif /* CONFIG_BCMA_DRIVER_MIPS */
+}
+
+static struct platform_device *bcma_hcd_create_pdev(struct bcma_device *dev,
+						    char *name, u32 addr)
+{
+	struct platform_device *hci_dev;
+	struct resource *hci_res;
+	int ret = -ENOMEM;
+
+	hci_res = kzalloc(sizeof(struct resource) * 2, GFP_KERNEL);
+	if (!hci_res)
+		return ERR_PTR(-ENOMEM);
+
+	hci_res[0].start = addr;
+	hci_res[0].end = hci_res[0].start + BCMA_CORE_SIZE - 1;
+	hci_res[0].flags = IORESOURCE_MEM;
+
+	hci_res[1].start = dev->irq;
+	hci_res[1].flags = IORESOURCE_IRQ;
+
+	hci_dev = platform_device_alloc(name, 0);
+	if (!hci_dev)
+		goto err_alloc;
+
+	hci_dev->dev.parent = &dev->dev;
+	hci_dev->dev.dma_mask = &hci_dev->dev.coherent_dma_mask;
+
+	ret = platform_device_add_resources(hci_dev, hci_res, 2);
+	if (ret)
+		goto err_alloc;
+
+	ret = platform_device_add(hci_dev);
+	if (ret) {
+err_alloc:
+		kfree(hci_res);
+		platform_device_put(hci_dev);
+		return ERR_PTR(ret);
+	}
+
+	return hci_dev;
+}
+
+static int bcma_hcd_probe(struct bcma_device *dev)
+{
+	int err;
+	u16 chipid_top;
+	struct bcma_hcd_device *usb_dev;
+
+	/* USBcores are only connected on embedded devices. */
+	chipid_top = (dev->bus->chipinfo.id & 0xFF00);
+	if (chipid_top != 0x4700 && chipid_top != 0x5300)
+		return -ENODEV;
+
+	/* TODO: Probably need checks here; is the core connected? */
+
+	if (dma_set_mask(dev->dma_dev, DMA_BIT_MASK(32)) ||
+	    dma_set_coherent_mask(dev->dma_dev, DMA_BIT_MASK(32)))
+		return -EOPNOTSUPP;
+
+	usb_dev = kzalloc(sizeof(struct bcma_hcd_device), GFP_KERNEL);
+	if (!usb_dev)
+		return -ENOMEM;
+
+	bcma_hcd_init_chip(dev);
+
+	usb_dev->ohci_dev = bcma_hcd_create_pdev(dev, "ohci-platform",
+						 dev->addr1);
+	if (IS_ERR(usb_dev->ohci_dev)) {
+		err = PTR_ERR(usb_dev->ohci_dev);
+		goto err_free_usb_dev;
+	}
+
+	usb_dev->ehci_dev = bcma_hcd_create_pdev(dev, "ehci-platform",
+						 dev->addr);
+	if (IS_ERR(usb_dev->ehci_dev)) {
+		err = PTR_ERR(usb_dev->ehci_dev);
+		goto err_unregister_ohci_dev;
+
+	}
+
+	bcma_set_drvdata(dev, usb_dev);
+	return 0;
+
+err_unregister_ohci_dev:
+	platform_device_unregister(usb_dev->ohci_dev);
+err_free_usb_dev:
+	kfree(usb_dev);
+	return err;
+}
+
+static void bcma_hcd_remove(struct bcma_device *dev)
+{
+	struct bcma_hcd_device *usb_dev;
+	struct platform_device *ohci_dev;
+	struct platform_device *ehci_dev;
+
+	usb_dev = bcma_get_drvdata(dev);
+	if (!usb_dev)
+		return;
+
+	ohci_dev = usb_dev->ohci_dev;
+	ehci_dev = usb_dev->ehci_dev;
+
+	if (ohci_dev) {
+		platform_device_unregister(ohci_dev);
+	}
+	if (ehci_dev) {
+		platform_device_unregister(ehci_dev);
+	}
+
+	bcma_core_disable(dev, 0);
+}
+
+static void bcma_hcd_shutdown(struct bcma_device *dev)
+{
+	bcma_core_disable(dev, 0);
+}
+
+#ifdef CONFIG_PM
+
+static int bcma_hcd_suspend(struct bcma_device *dev, pm_message_t state)
+{
+	bcma_core_disable(dev, 0);
+
+	return 0;
+}
+
+static int bcma_hcd_resume(struct bcma_device *dev)
+{
+	bcma_core_enable(dev, 0);
+
+	return 0;
+}
+
+#else /* !CONFIG_PM */
+#define bcma_hcd_suspend	NULL
+#define bcma_hcd_resume	NULL
+#endif /* CONFIG_PM */
+
+static const struct bcma_device_id bcma_hcd_table[] = {
+	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_USB20_HOST, BCMA_ANY_REV, BCMA_ANY_CLASS),
+	BCMA_CORETABLE_END
+};
+MODULE_DEVICE_TABLE(bcma, bcma_hcd_table);
+
+static struct bcma_driver bcma_hcd_driver = {
+	.name		= KBUILD_MODNAME,
+	.id_table	= bcma_hcd_table,
+	.probe		= bcma_hcd_probe,
+	.remove		= bcma_hcd_remove,
+	.shutdown	= bcma_hcd_shutdown,
+	.suspend	= bcma_hcd_suspend,
+	.resume		= bcma_hcd_resume,
+};
+
+static int __init bcma_hcd_init(void)
+{
+	return bcma_driver_register(&bcma_hcd_driver);
+}
+module_init(bcma_hcd_init);
+
+static void __exit bcma_hcd_exit(void)
+{
+	bcma_driver_unregister(&bcma_hcd_driver);
+}
+module_exit(bcma_hcd_exit);