ca4832fcac
The stock firmware of the ZyXEL GS1900 series use a non-standard u-image magic. This is not enforced by the stock u-boot, which is why we could boot images with the default magic. The flash management application of the stock firmware will however verify the magic, and refuse any image with another value. Convert to vendor-specific value to get flash management support in stock firmware, including the ability to upgrade to OpenWrt directly from stock web UI. Signed-off-by: Bjørn Mork <bjorn@mork.no>
150 lines
2.4 KiB
Plaintext
150 lines
2.4 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
#include "rtl838x.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
aliases {
|
|
led-boot = &led_sys;
|
|
led-failsafe = &led_sys;
|
|
led-running = &led_sys;
|
|
led-upgrade = &led_sys;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
gpio1: rtl8231-gpio {
|
|
status = "okay";
|
|
|
|
poe_enable {
|
|
gpio-hog;
|
|
gpios = <13 0>;
|
|
output-high;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_sys: sys {
|
|
label = "green:sys";
|
|
gpios = <&gpio0 47 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x40000>;
|
|
read-only;
|
|
};
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
partition@50000 {
|
|
label = "u-boot-env2";
|
|
reg = <0x50000 0x10000>;
|
|
read-only;
|
|
};
|
|
partition@60000 {
|
|
label = "jffs";
|
|
reg = <0x60000 0x100000>;
|
|
};
|
|
partition@160000 {
|
|
label = "jffs2";
|
|
reg = <0x160000 0x100000>;
|
|
};
|
|
partition@b260000 {
|
|
label = "firmware";
|
|
reg = <0x260000 0x6d0000>;
|
|
compatible = "openwrt,uimage", "denx,uimage";
|
|
openwrt,ih-magic = <0x83800000>;
|
|
};
|
|
partition@930000 {
|
|
label = "runtime2";
|
|
reg = <0x930000 0x6d0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet0 {
|
|
mdio: mdio-bus {
|
|
compatible = "realtek,rtl838x-mdio";
|
|
regmap = <ðernet0>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
INTERNAL_PHY(8)
|
|
INTERNAL_PHY(9)
|
|
INTERNAL_PHY(10)
|
|
INTERNAL_PHY(11)
|
|
INTERNAL_PHY(12)
|
|
INTERNAL_PHY(13)
|
|
INTERNAL_PHY(14)
|
|
INTERNAL_PHY(15)
|
|
};
|
|
};
|
|
|
|
&switch0 {
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
SWITCH_PORT(8, 1, internal)
|
|
SWITCH_PORT(9, 2, internal)
|
|
SWITCH_PORT(10, 3, internal)
|
|
SWITCH_PORT(11, 4, internal)
|
|
SWITCH_PORT(12, 5, internal)
|
|
SWITCH_PORT(13, 6, internal)
|
|
SWITCH_PORT(14, 7, internal)
|
|
SWITCH_PORT(15, 8, internal)
|
|
|
|
port@28 {
|
|
ethernet = <ðernet0>;
|
|
reg = <28>;
|
|
phy-mode = "internal";
|
|
|
|
fixed-link {
|
|
speed = <1000>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
};
|
|
};
|