c846dd91f0
Like in the previous patch for ath79 target, this will remove the "devicename" from LED labels in ramips as well. The devicename is removed in DTS files and 01_leds, consolidation of definitions into DTSI files is done where (easily) possible, and migration scripts are updated. For the latter, all existing definitions were actually just devicename migrations anyway. Therefore, those are removed and a common migration file is created in target base-files. This is actually another example of how the devicename removal makes things easier. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
189 lines
2.9 KiB
Plaintext
189 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "mt7620a.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
/ {
|
|
compatible = "dlink,dwr-960", "ralink,mt7620a-soc";
|
|
model = "D-Link DWR-960";
|
|
|
|
aliases {
|
|
led-boot = &led_status;
|
|
led-failsafe = &led_status;
|
|
led-running = &led_status;
|
|
led-upgrade = &led_status;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_status: status {
|
|
label = "green:status";
|
|
gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wan {
|
|
label = "green:wan";
|
|
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
lan {
|
|
label = "green:lan";
|
|
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
sms {
|
|
label = "green:sms";
|
|
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
signal_green {
|
|
label = "green:signal";
|
|
gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
signal_red {
|
|
label = "red:signal";
|
|
gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
4g {
|
|
label = "green:4g";
|
|
gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
3g {
|
|
label = "green:3g";
|
|
gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan5g {
|
|
label = "green:wlan5g";
|
|
gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
wlan2g {
|
|
label = "green:wlan2g";
|
|
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&rgmii2_pins &mdio_pins>;
|
|
|
|
mediatek,portmap = "wllll";
|
|
|
|
port@5 {
|
|
status = "okay";
|
|
phy-mode = "rgmii-txid";
|
|
phy-handle = <&phy7>;
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy7: ethernet-phy@7 {
|
|
reg = <7>;
|
|
phy-mode = "rgmii-id";
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio2 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <50000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "jboot";
|
|
reg = <0x0 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@10000 {
|
|
compatible = "amit,jimage";
|
|
label = "firmware";
|
|
reg = <0x10000 0xfe0000>;
|
|
};
|
|
|
|
config: partition@ff0000 {
|
|
label = "config";
|
|
reg = <0xff0000 0x10000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
};
|
|
|
|
&pcie0 {
|
|
wifi@0,0 {
|
|
compatible = "mediatek,mt76";
|
|
reg = <0x0000 0 0 0 0>;
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
mediatek,mtd-eeprom = <&config 0xe08e>;
|
|
mtd-mac-address = <&config 0xe50e>;
|
|
mtd-mac-address-increment = <2>;
|
|
};
|
|
};
|
|
|
|
&state_default {
|
|
default {
|
|
groups = "i2c", "wled", "spi refclk", "uartf", "ephy";
|
|
function = "gpio";
|
|
};
|
|
};
|