b123ffdf6e
All definitions of gpio in SoC DTSI files do not set status, i.e. have it enabled. This drops all remaining redundant "status = okay" definitions in descendent files (mostly older ones). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
181 lines
2.9 KiB
Plaintext
181 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9344.dtsi"
|
|
|
|
/ {
|
|
model = "Devolo Magic 2 Wifi";
|
|
compatible = "devolo,magic-2-wifi", "qca,ar9344";
|
|
|
|
aliases {
|
|
led-boot = &led_dlan_red;
|
|
led-failsafe = &led_dlan_red;
|
|
led-running = &led_dlan_white;
|
|
led-upgrade = &led_dlan_red;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan {
|
|
label = "devolo:white:wlan";
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
led_dlan_white: dlan_white {
|
|
label = "devolo:white:dlan";
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
led_dlan_red: dlan_red {
|
|
label = "devolo:red:dlan";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
|
panic-indicator;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
wifi {
|
|
label = "WIFI button";
|
|
linux,code = <KEY_RFKILL>;
|
|
gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
|
|
debounce-interval = <60>;
|
|
};
|
|
|
|
dlan {
|
|
label = "DLAN button";
|
|
linux,code = <BTN_0>;
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio {
|
|
wlan_power {
|
|
gpio-hog;
|
|
line-name = "WLAN power";
|
|
gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
|
|
output-high;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
uboot: partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "Config1";
|
|
reg = <0x50000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "Config2";
|
|
reg = <0x60000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@70000 {
|
|
compatible = "denx,uimage";
|
|
label = "firmware";
|
|
reg = <0x70000 0xf80000>;
|
|
};
|
|
|
|
art: partition@ff0000 {
|
|
label = "art";
|
|
reg = <0xff0000 0x10000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x02000000 0x00000101 0x00001616>;
|
|
|
|
mtd-mac-address = <&art 0x1002>;
|
|
mtd-mac-address-increment = <2>;
|
|
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy0>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
};
|
|
|
|
&pcie {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "qcom,ath10k";
|
|
reg = <0 0 0 0 0>;
|
|
};
|
|
};
|
|
|
|
&mdio0 {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "rgmii";
|
|
|
|
qca,ar8327-initvals = <
|
|
/* PORT0: RGMII, MAC0/6 exchage, tx_delay 01, No rx_delay */
|
|
0x04 0x06400000
|
|
0x08 0x00000000 /* PORT5 PAD MODE CTRL */
|
|
0x0c 0x00000000 /* PORT6 PAD MODE CTRL */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
>;
|
|
};
|
|
};
|