53a7d5d614
DTR GPIO isn't actually needed and triggers boot warning.
TX pin was off by one (GPIO 19 instead of GPIO 18).
Reported-by: @tophirsch
Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
174 lines
2.9 KiB
Plaintext
174 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
#include "ar9344.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "teltonika,rut9xx", "qca,ar9344";
|
|
|
|
aliases {
|
|
serial1 = &hs_uart;
|
|
label-mac-device = ð1;
|
|
};
|
|
|
|
i2c0: i2c {
|
|
compatible = "i2c-gpio";
|
|
scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
|
sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
hwmon@4d {
|
|
compatible = "microchip,mcp3221";
|
|
reg = <0x4d>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ref {
|
|
clock-frequency = <40000000>;
|
|
};
|
|
|
|
&hs_uart {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pmx_uart2>;
|
|
|
|
rts-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
rs485-rts-active-low;
|
|
linux,rs485-enabled-at-boot-time;
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pmx_spi>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
config: partition@20000 {
|
|
label = "config";
|
|
reg = <0x20000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
art: partition@30000 {
|
|
label = "art";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "firmware";
|
|
reg = <0x40000 0xf30000>;
|
|
compatible = "tplink,firmware";
|
|
};
|
|
|
|
partition@f70000 {
|
|
label = "event-log";
|
|
reg = <0xf70000 0x90000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
|
|
microsd@1 {
|
|
status = "disabled";
|
|
|
|
compatible = "mmc-spi-slot";
|
|
spi-max-frequency = <25000000>;
|
|
reg = <1>;
|
|
voltage-ranges = <3200 3400>;
|
|
broken-cd;
|
|
};
|
|
};
|
|
|
|
&usb {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
port@1 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <1>;
|
|
|
|
port@1 {
|
|
compatible = "usb-a-connector";
|
|
reg = <1>;
|
|
};
|
|
|
|
port@3 {
|
|
label = "RS-232 serial adapter";
|
|
reg = <3>;
|
|
};
|
|
|
|
port@4 {
|
|
label = "internal wwan modem";
|
|
reg = <4>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&config 0x0>;
|
|
mtd-mac-address-increment = <2>;
|
|
};
|
|
|
|
&pinmux {
|
|
pmx_spi: spi {
|
|
// SPI_CS1 on GPIO 3
|
|
pinctrl-single,bits = <0x0 0x07000000 0xff000000>;
|
|
};
|
|
|
|
pmx_leds_switch: leds_switch {
|
|
// switch port LEDs on GPIO 1, GPIO 13, GPIO 14 and GPIO 22
|
|
pinctrl-single,bits = <0x00 0x00002d00 0x0000ff00>,
|
|
<0x0c 0x002c2b00 0x00ffff00>,
|
|
<0x14 0x002a0000 0x00ff0000>;
|
|
};
|
|
|
|
pmx_uart2: uart2 {
|
|
// UART1_DTR on GPIO 0, UART1_RD on GPIO 11, UART1_TD on GPIO 18
|
|
pinctrl-single,bits = <0x00 0x00000000 0x000000ff>,
|
|
<0x10 0x004f0000 0x00ff0000>,
|
|
<0x3c 0x000b0000 0x00ff0000>;
|
|
};
|
|
};
|