3a4b751110
The uart node is enabled on all devices except one (GL-USB150 *). Thus, let's not have a few hundred nodes to enable it, but do not disable it in the first place. Where the majority of devices is using it, also move the serial0 alias to the DTSI. *) Since GL-USB150 even defines serial0 alias, the missing uart is probably just a mistake. Anyway, disable it for now so this patch stays cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
196 lines
3.5 KiB
Plaintext
196 lines
3.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
#include "ath79.dtsi"
|
|
|
|
/ {
|
|
compatible = "qca,ar9132";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
cpu@0 {
|
|
device_type = "cpu";
|
|
compatible = "mips,mips24Kc";
|
|
clocks = <&pll ATH79_CLK_CPU>;
|
|
reg = <0>;
|
|
};
|
|
};
|
|
|
|
cpuintc: interrupt-controller {
|
|
compatible = "qca,ar9132-cpu-intc", "qca,ar7100-cpu-intc";
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
|
|
qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>;
|
|
qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>,
|
|
<&ddr_ctrl 0>, <&ddr_ctrl 1>;
|
|
};
|
|
|
|
ahb {
|
|
compatible = "simple-bus";
|
|
ranges;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
interrupt-parent = <&cpuintc>;
|
|
|
|
apb {
|
|
compatible = "simple-bus";
|
|
ranges;
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
interrupt-parent = <&miscintc>;
|
|
|
|
ddr_ctrl: memory-controller@18000000 {
|
|
compatible = "qca,ar9132-ddr-controller",
|
|
"qca,ar7240-ddr-controller";
|
|
reg = <0x18000000 0x100>;
|
|
|
|
#qca,ddr-wb-channel-cells = <1>;
|
|
};
|
|
|
|
uart: uart@18020000 {
|
|
compatible = "ns8250";
|
|
reg = <0x18020000 0x20>;
|
|
interrupts = <3>;
|
|
|
|
clocks = <&pll ATH79_CLK_AHB>;
|
|
clock-names = "uart";
|
|
|
|
reg-io-width = <4>;
|
|
reg-shift = <2>;
|
|
no-loopback-test;
|
|
};
|
|
|
|
gpio: gpio@18040000 {
|
|
compatible = "qca,ar9132-gpio",
|
|
"qca,ar7100-gpio";
|
|
reg = <0x18040000 0x30>;
|
|
interrupts = <2>;
|
|
|
|
ngpios = <22>;
|
|
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pll: pll-controller@18050000 {
|
|
compatible = "qca,ar9132-pll",
|
|
"qca,ar9130-pll", "syscon";
|
|
reg = <0x18050000 0x20>;
|
|
|
|
clock-names = "ref";
|
|
/* The board must provides the ref clock */
|
|
|
|
#clock-cells = <1>;
|
|
clock-output-names = "cpu", "ddr", "ahb";
|
|
};
|
|
|
|
wdt: wdt@18060008 {
|
|
compatible = "qca,ar7130-wdt";
|
|
reg = <0x18060008 0x8>;
|
|
|
|
interrupts = <4>;
|
|
|
|
clocks = <&pll ATH79_CLK_AHB>;
|
|
clock-names = "wdt";
|
|
};
|
|
|
|
miscintc: interrupt-controller@18060010 {
|
|
compatible = "qca,ar9132-misc-intc",
|
|
"qca,ar7100-misc-intc";
|
|
reg = <0x18060010 0x8>;
|
|
|
|
interrupt-parent = <&cpuintc>;
|
|
interrupts = <6>;
|
|
|
|
interrupt-controller;
|
|
#interrupt-cells = <1>;
|
|
};
|
|
|
|
rst: reset-controller@1806001c {
|
|
compatible = "qca,ar9132-reset",
|
|
"qca,ar7100-reset";
|
|
reg = <0x1806001c 0x4>;
|
|
|
|
#reset-cells = <1>;
|
|
};
|
|
};
|
|
|
|
usb: usb@1b000100 {
|
|
compatible = "qca,ar7100-ehci", "generic-ehci";
|
|
reg = <0x1b000100 0x100>;
|
|
|
|
interrupts = <3>;
|
|
resets = <&rst 5>;
|
|
|
|
has-transaction-translator;
|
|
|
|
phy-names = "usb";
|
|
phys = <&usb_phy>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
spi: spi@1f000000 {
|
|
compatible = "qca,ar9132-spi", "qca,ar7100-spi";
|
|
reg = <0x1f000000 0x10>;
|
|
|
|
clocks = <&pll ATH79_CLK_AHB>;
|
|
clock-names = "ahb";
|
|
|
|
status = "disabled";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
};
|
|
|
|
wmac: wmac@180c0000 {
|
|
compatible = "qca,ar9130-wmac";
|
|
reg = <0x180c0000 0x230000>;
|
|
|
|
interrupts = <2>;
|
|
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
usb_phy: usb-phy {
|
|
compatible = "qca,ar7200-usb-phy";
|
|
|
|
reset-names = "usb-phy", "usb-suspend-override";
|
|
resets = <&rst 4>, <&rst 3>;
|
|
|
|
#phy-cells = <0>;
|
|
|
|
status = "disabled";
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
compatible = "qca,ar9130-eth", "syscon";
|
|
reg = <0x19000000 0x200
|
|
0x18070000 0x4>;
|
|
pll-data = <0x1a000000 0x13000a44 0x00441099>;
|
|
pll-reg = <0x4 0x14 20>;
|
|
pll-handle = <&pll>;
|
|
resets = <&rst 9>;
|
|
reset-names = "mac";
|
|
qca,mac-idx = <0>;
|
|
};
|