All chipsets from AR7100 up to QCA9563 have three dedicated chipselect
lines for the integrated SPI controller. Remove the number of
chipselects from the platform data, as there is no need to manually set
this to a different value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the SPI_MASTER_GPIO_SS flag for the spi-ath79 driver. Otherwise,
the custom chipselect function is never called. This breaks hardware,
where the three dedicated chipselect lines are used instead of generic
GPIO pins.
Signed-off-by: David Bauer <mail@david-bauer.net>
This came up in an upstream commit: "
b1dd9bf688b0 "net: phy: broadcom: Fix RGMII delays for BCM50160 and BCM50610M"
The PHY driver entry for BCM50160 and BCM50610M calls
bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in
order to configuration appropriate clock delays on the PHY, fix that."
So the "rgmii" phy-mode has always been wrong, but went unnoticed since
the broadcom phy driver didn't push the delay settings to the chip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
QLCNIC_HWMON was activated when hwmon was set, but the dependency was
missing. This broke the build bot builds. Fix this by explicitly
activating HWMON support and adding a dependency.
Fixes: f88c64d28c ("kernel: netdev: add qlcnic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CLK125 output pin at the ethernet PHY is connected via capacitor to
GND and nowhere else. Disable it. Also tune the LED masks.
The MPP56 and MPP60 pins at the SoC are conected to the μPD720202 USB3.0
chip:
- MPP56: wired to PCIe CLKREQ# (out)
- MPP60: wired to PCIe RESET# (in)
Configure the pcie pinmux for these pins.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
These have long been obsolete. For reference, here's the Linux version where
each symbol has been dropped:
CONFIG_IP6_NF_QUEUE - 3.5
CONFIG_IP6_NF_TARGET_LOG - 3.4
CONFIG_IP_NF_MATCH_DSCP - 2.6.19
CONFIG_NF_CONNTRACK_IPV4 - 4.19
CONFIG_NF_CONNTRACK_IPV6 - 4.19
CONFIG_NF_CONNTRACK_RTCACHE - out-of-tree, superseded by flow offloading
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This kmod is similar to macvlan with the difference being that the
endpoints have the same mac address.
It is useful on cloud where only one mac address allowed on port,
where macvlan not works but ipvlan would.
One use case is where multiple IPs and gateways assign on one net port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new EEE patch is accepted upstream, so backport it and replace the
current one.
Cc: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
This CFI patch was accepted upstream for 5.13. Move it away from under
ath79 and place under backports to be removed in due time.
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
Since support for SFP on the MikroTik RouterBOARD 922UAGS-5HPacD was
added by 4387fe00cb, the MAC addresses for eth0 (Ethernet) and eth1
(SFP) were swapped. This patch fixes the 02_network script to assign MAC
addresses correctly, so they match the label and the vendor's OS.
Tested on a RouterBOARD 922UAGS-5HPacD board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Erase firmware ereas before writing to recovery or production partition
when updating them via the bootloader menu.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Ubiquiti Networks UniFi 6 LR access point comes with a total of
512 MB RAM provided by 2x 8-bit DDR3 SDRAM. This combination lead to
problems with the DDR calibration on boot resulting in occasional hang
on boot. Use updated calibration binary provided by MediaTek to make
boot on that device more reliable.
The binary has also been tested on the BananaPi BPi-R64 board and that
also works just fine with the new binary.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Missing braces in a macro were leading to badly working rates sometimes
getting a success probabilty of 1.0
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit f724a583dc updated the nand-rb4xx driver to the 5.10 testing
kernel, but forgot to add the new kernel config symbol it introduces to
the 5.10 config.
Fixes: f724a583dc ("ath79: mikrotik: update nand-rb4xx driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
When running multiple instances of dnsmasq, for example one being for the lan
and another for a guest network, it might not be desirable to have the same dns names
configured in both networks
Signed-off-by: João Henriques <joaoh88@gmail.com>
9df230a Zero checksum handling (#25)
7688102 skip generating a UDP4 csum if the UDP6 csum is 0 and zero_csum_pass is set
4a9e4b1 zero csum: avoid calling the checksum adjustment function if udp csum is zero
2de14c5 add a module argument to skip checksum adjust for UDP if checksum is zero
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to the latest stable upstream version.
Drop unneeded make variables to remove redundant assignments seen during
invocation of package Makefile.
Also remove the following patch now included upstream:
* 200-fix-install-param-order-on-macos.patch
Compile and run-tested on malta/mips32be, using bpftool directly and also
libbpf (linked with tc) to inspect and load simple eBPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Rename feature variable clang-bpf-global-var following upstream changes.
This restores the HAVE_CLANG feature override and should avoid rare build
errors where a recent host clang and BTF-enabled host kernel are present.
Fixes: 23be333401 ("bpftools: update to 5.10.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The 'append-image-stage' command doesn't work when setting the
EXTRA_IMAGE_NAME option of the ImageBuilder as in that case
DEVICE_IMG_PREFIX is modified and no longer matches the value it had in
buildroot. Choose a filename independent of DEVICE_IMG_PREFIX for
images staged using 'append-image-stage' to fix that.
Fixes: de4b29dab9 ("image: introduce 'append-image-stage' build command")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Generating the sdcard.img.gz file requires the initramfs/recovery
image to be present. Use the newly introduced 'append-image-stage'
build command to fix the ImageBuilder for the BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to 'append-image' this new command appends an existing binary.
'append-image-stage' also makes a copy of that binary and keeps it in
$(STAGING_DIR_IMAGE). When called from within the ImageBuilder, this
copy is used instead of expecting the binary to be present.
This is useful for artifacts which include the initramfs/recovery image
which is usually not included in the ImageBuilder.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build the driver for the in-SoC AHCI SATA host as module, just like for
the other subtargets. No board requires booting off SATA, so we don't
need to have it built-in. All boards with SATA support already select
kmod-ata-ahci-mtk which provides the module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Skip building Makefile targets that aren't packaged: tipc, dcb, ifstat,
rtacct, lnstat, and man. Also, only compile targets needed for the current
build variant i.e. don't compile 'tc' when building an 'ip' variant and
vice versa.
These changes reduce typical build times by over 30%:
$ make package/iproute2/clean && time make -j8 package/iproute2/compile
(old)
...
real 2m24.985s
user 3m12.537s
sys 0m26.677s
(new)
...
real 1m36.945s
user 2m8.734s
sys 0m20.046s
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
It's in backports-5.4, but it wasn't ever merged. Upstream followed another
approach, with flow offloading, which has much better performance. Drop this
obsolete patch and refresh the kernel patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Make sure all compression algorithms are enabled, for the time being, in order
not to break sysupgrade. In the future, we'd like to disable all except zstd, as
it's the best all-around performer.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Update the uboot-rockchip to the latest upstream release.
Remove upstreamed patches.
Tested-on: FriendlyElec NanoPi R2S
Signed-off-by: David Bauer <mail@david-bauer.net>
Only two patches against mainline remains. Switch to v5.10
which works very nicely with all Gemini devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[backported don't disable option CONFIG_BPF_SYSCAL]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove upstreamed parts from 100-ubnt_edgerouter2_support.patch.
Compile and runtime tested on Ubiquiti EdgeRouter Lite.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
