This adds basic support for Radxa Rock Pi 4
Specification:
- RAM: 1 GB/ 2 GB/4 GB LPDDR4
- SoC: Rockchip RK3399
- CPU: 64bit hexa core processor
Dual Cortex-A72, freqency 1.8Ghz
with quad Cortex-A53, frequency 1.4Ghz
- USB: USB 3.0 OTG x1
hardware switch for host/device switch, upper one
USB 3.0 HOST x1
dedicated USB3.0 channel, lower one
USB 2.0 HOST x2
- Ethernet: 1x GbE
- Storage: eMMC module
uSD card
M.2 SSD
- Wireless: 802.11 ac wifi
Bluetooth 5.0
currently not supported
firmware Installation
======================
gzip -d xxx.img.gz, then dd the .img to SD/eMMC
======================
Device Tested: ROCK PI 4 Model B v1.3
Signed-off-by: Marty Jones <mj8263788@gmail.com>
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
1GB DDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
USB 2.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
MAC-address
-----------
The vendor code supports reading a MAC address from an EEPROM connected
via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC
address in binary at offset 0xfa. However, my two units didn't come with
such an EEPROM soldered on. The EEPROM should be placed between the SoC
and the GPIO pins on the board. (U10)
Generating rendom MAC addresses works around this issue. Otherwise, all
boards running the same image have identical MAC addresses.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add support for select a bootscript depending on the device built. This
is necessary, as the FriendlyARM NanoPi R2S needs a different bootcmd in
order to produce output on the debug UART.
Signed-off-by: David Bauer <mail@david-bauer.net>
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.
This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.
For sunxi, this includes a trivial rename of the subtarget image
Makefiles.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds the new rockchip target and support for RockPro64 RK3399
Flash: 16 MiB SPI NOR
RAM: 2 GiB/4 GiB LPDDR4
SoC: RK3399
USB: 2x USB 2.0, 1x USB 3.0, 1x USB-C
Ethernet: 1x GbE
PCIe: PCIe 2.0, 4 lanes
Storage: eMMC or SD card
Optional SDIO wifi/bt module
The Pine64 RockPro64 is a single-board-computer with a 4x PCIe connector,
6 ARM64 cores (4 little, 2 big), plenty of RAM and storage.
By default the single Gigabit-Ethernet port is configured as the
LAN port.
Installation of the firware is possible by dd'ing the image
to an SD card or the eMMC flash.
Serial: 3v3 1500000 8n1
U-boot is build from the mainline tree and
integrated into the images. Required ATF to build u-boot
is downloaded from a CI build bot.
Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
