The mkits.sh script help message states hash algorithm can be
specified using the -H command-line option, but it does not work
currently due to a bug in the script.
This patch fixes this problem by changing the option from -S to
-H and specify getopts parameter after it
Signed-off-by: Yonghyu Ban <yonghyu@empo.im>
NR_CPUS limits the number of CPUs supported to 8. This makes total sense
on hardware-restircted platforms, but not on x86_64, where CPUs with
more than 8 cores can be easily acquired and with less physical limitaions.
see also: https://forum.openwrt.org/t/x86-64-8-cpu-limitation-on-vanilla-release/100946
Signed-off-by: Edgar Su <sjs333@outlook.com>
When compiling with all modules enabled, Kconfig complains about
CONFIG_I2C_DESIGNWARE_SLAVE being unset. Disable this symbol by default.
Fixes commit e9c9b5ec72 ("kernel: package Synopsys Designware PCI to I2C controller")
Signed-off-by: David Bauer <mail@david-bauer.net>
When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the
at803x PHY driver incorrectly set up the delays, not disabling delays
set by the bootloader.
The PHY was always operating with RX as well as TX delays enabled, but
with kernel 5.4 and later, the required TX delay is disabled, breaking
ethernet operation.
Correct the PHY mode, so the driver enables both delays.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add gcc 11 version. Same patches of gcc 10.
Build tested on: ipq806x ipq807x
Run tested on: ipq806x ipq807x
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
0ee73b2 uxc: implement support for rootfs overlay in containers
b0a8ea1 jail: do not hack /etc/resolv.conf on container rootfs
92aba53 jail: increase max additional env records to 64
15997e6 jail: allow rootfs to be a symbolic link
0114c6f jail: open() extroot folder before mounting
ed96eda uxc: check for required blockd mounts
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This will restart the interface in case the CSA fails and can be used to
force the device on a DFS channel (including full CAC)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
4d4dcfb blockd: detect mountpoint of /dev/mapper/*
2f42515 block: resolve /dev/mapper/* name for /dev/dm-0 when hotplugging
39558a1 blockd: also send ubus notification on mount hotplug
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
b5711025bc x86_64: Remove unneeded static PIE check for undefined weak diagnostic
edfd11197e wordexp: handle overflow in positional parameter number (bug 28011)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
f12b073c0cc3 wireless: add some comments to functions
b0d090688302 bridge: fix setting pvid for updated vlans
ff3764ce28e0 device: move hotplug handling logic from system-linux.c to device.c
16bff892f415 ubus: add a dummy mode ubus call to simulate hotplug events
7f30b02013f2 examples: make dummy wireless vif names shorter
013a1171e9b0 device: do not treat devices with non-digit characters after . as vlan devices
f037b082923a wireless: handle WDS per-sta devices
db0fa24e1c17 bridge: fix enabling hotplug-added VLANs on the bridge port
4e92ea74273f bridge: bring up pre-existing vlans on hotplug as well
1f283c654aeb bridge: fix hotplug vlan overwrite on big-endian systems
Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ! Behavior change !
Old behavior: If the Reset button is held down during power-on
do factory reset and try booting recovery from TFTP forever.
If valid recovery is received via TFTP, write it to flash and boot.
New behavior: If the Reset button is held down during power-on
do factory reset, then try TFTP *once*, then try booting on-flash
recovery, then keep trying via TFTP forever until a valid image is
received.
Only if there is no bootable recovery stored on flash, store the
downloaded recovery. Then boot it.
* Set loadaddr to 0x48000000 in order to allow booting images larger
than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to
0x48000000 gives us 384MB on devices with 512MB RAM, which should be
more than enough as a maximum size for uImage.FIT to be loaded.
* Widely unify device-specific default environment in preparation to
auto-generate it from parameters.
* backport upstream commit fixing MBR/DOS partitioning
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commands in 10_fix_wifi_mac were not properly concatenated, so
this was also triggered for the second phy without giving a
MAC address as argument.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MT7621AT
* RAM: 256MB
* Flash: 128MB NAND flash
* WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC
* LAN: 5x1000M
* Firmware layout is Uboot with extra 96 bytes in header
* Base PCB is DIR-1360 REV1.0
* LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue,
USB Blue
* Buttons Reset,WPS, Wifi
MAC addresses on OEM firmware:
lan factory 0xe000 f4:*:*:a8:*:65 (label)
wan factory 0xe006 f4:*:*:a8:*:68
2.4 GHz [not on flash] f6:*:*:c8:*:66
5.0 GHz factory 0x4 f4:*:*:a8:*:66
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
f4:XX:XX:a8:XX:66 f6:XX:XX:c8:XX:66 +0x20
x0:xx:xx:68:xx:xx x2:xx:xx:48:xx:xx -0x20
x4:xx:xx:6a:xx:xx x6:xx:xx:4a:xx:xx -0x20
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Flashing instruction:
The Dlink "Emergency Room" cannot be accessed through the reset
button on this device. You can either use console or use the
encrypted factory image availble in the openwrt forum.
Once the encrypted image is flashed throuh the stock Dlink web
interface, the sysupgrade images can be used.
Header pins needs to be soldered near the WPS and Wifi buttons.
The layout for the pins is (VCC,RX,TX,GND). No need to connect the VCC.
the settings are:
Bps/Par/Bits : 57600 8N1
Hardware Flow Control : No
Software Flow Control : No
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device
At the time of adding support the wireless config needs to be set up by
editing the wireless config file:
* Setting the country code is mandatory, otherwise the router loses
connectivity at the next reboot. This is mandatory and can be done
from luci. After setting the country code the router boots correctly.
A reset with the reset button will fix the issue and the user has to
reconfigure.
* This is minor since the 5g interface does not come up online although
it is not set as disabled. 2 options here:
1- Either run the "wifi" command. Can be added from LUCI in system -
startup - local startup and just add wifi above "exit 0".
2- Or add the serialize option in the wireless config file as shown
below. This one would work and bring both interfaces automatically
at every boot:
config wifi-device 'radio0'
option serialize '1'
config wifi-device 'radio1'
option serialize '1'
Signed-off-by: Karim Dehouche <karimdplay@gmail.com>
[rebase, improve MAC table, update wireless config comment, fix
2.4g macaddr setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Tom Wizetek (@wizetek) for testing.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
a0a0e02 iwinfo: rename hardware.txt to devices.txt
Also split common devices.txt (former hardware.txt) into a common
libiwinfo-data package to allow different libiwinfo versions to
coexist without file clashes.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The mx25l25635f supports clock speed up to 50Mhz.
Also remove obsolete "mx25l25635f" hack and rename
the matching device-tree flash node.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[mention node rename as well. chip is very very likely
always the "f" revision for all NBG6617]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This PR adds support for router D-Link DIR-853-R1
Specifications:
SoC: MT7621AT
RAM: 128MB
Flash: 16MB SPI
WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC (This mode allows this
single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time)
LAN: 5x1000M
LEDs Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue
USB Blue
Buttons Reset,WPS, Wifi
MAC addresses:
|Interface | MAC | Factory |Comment
|------------|-----------------|-------------|----------------
|WAN sticker |C4:XX:XX:6E:XX:2A| |Sticker
|LAN |C4:XX:XX:6E:XX:2B| |
|Wifi (5g) |C4:XX:XX:6E:XX:2C|0x4 |
|Wifi (2.4g) |C6:XX:XX:7E:XX:2C| |
| | | |
| |C4:XX:XX:6E:XX:2E|0x8004 0xe000|
| |C4:XX:XX:6E:XX:2F|0xe006 |
The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:
5g 2.4g increment
C4:XX:XX:6E:XX:2C C6:XX:XX:7E:XX:2C 0x10
f4:XX:XX:16:XX:32 f6:XX:XX:36:XX:32 0x20
F4:XX:XX:A6:XX:E3 F6:XX:XX:B6:XX:E3 0x10
Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.
Flashing instruction:
The Dlink "Emergency Room"
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.101 / 255.255.255.0.
Then, power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing
Call the recovery page or tftp for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device.
Signed-off-by: Stas Fiduchi <fiduchi@protonmail.com>
[commit title/message improvements, use correct label MAC address,
calculate MAC addresses based on 0x4, minor DTS style fixes, add
uart2 to state_default, remove factory image, add 2.4g MAC address,
use partition DTSI, add macaddr comment in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Looks like the symbol was forgotten for 5.4
Fixes: 820e660cd7 ("ath79: add NAND driver for MikroTik RB91xG series")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The MX25L12805D used on all ath79 OCEDO boards supports clock
speeds up to 50 MHz.
Thus, we can increase the maximum SPI frequency the flash chip is
controlled at to 50 MHz, increasing transfer speed.
Signed-off-by: David Bauer <mail@david-bauer.net>
