This commit adds support for the Teltonika RUT230 v1, a Atheros AR9331
based router with a Quectel UC20 UMTS modem.
Hardware
--------
Atheros AR9331
16 MB SPI-NOR XTX XT25F128B
64M DDR2 memory
Atheros AR9331 1T1R 802.11bgn Wireless
Boootloader: pepe2k U-Boot mod
Hardware-Revision
-----------------
There are two board revisions of the RUT230, a v0 and v1.
A HW version is silkscreened on the top of the PCBs front side as well
as shown in the Teltonika UI. However, this looks to be a different
identifier, as the GPl dump shows this silkscreened / UI shown version
are internally treated identically.
Th following mapping has been obtained from the latest GPl dump.
HW Ver 01 - 04 --> v0
HW Ver > 05 --> v1
My board was a HW Ver 09 and is treated as a v1.
Installation
------------
While attaching power, hold down the reset button and release it after
the signal LEDs flashed 3 times.
Attach your Computer with the devices LAN port and assign yourself the
IPv4 address 192.168.1.10/24. Open a web browser, navigate to
192.168.1.1. Upload the OpenWrt factory image.
The device will install OpenWrt and automatically reboots afterwards.
You can use the smae procedure with the stock firmware to return back to
the vendor firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently, when using multiple dnsmasq instances they are all assigned
to the same Ubus instance name. This does not work, as only a single
instance can register with Ubus at a time. In the log, this leads to
`Cannot add object to UBus: Invalid argument` error messages.
Furthermore, upstream 3c93e8eb41952a9c91699386132d6fe83050e9be changes
behaviour so that instead of the log, dnsmasq exits at start instead.
With this patch, all dnsmasq instances are assigned unique names so that
they can register with Ubus concurrently. One of the enabled instances
is always assigned the previous default name "dnsmasq" to avoid breaking
backwards compatibility with other software relying on that default.
Previously, a random instance got assigned that name (while the others
produced error logs). Now, the first unnamed dnsmasq config section is
assigned the default name. If there are no unnamed dnsmasq sections the
first encountered named dnsmasq config section is assigned instead.
A similar issue exists for Dbus and was similarly addressed.
Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
[tweaked commit message] dnsmasq was not crashing it is exiting
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
commit 5edbd390d321532d9a697d6895a1a7c71c40bd5d rearranged the
"wifi up" code.
This commit tidies up the "wifi reconf" code so as to
keep it aligned with the "wifi up" code.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
"/sbin/wifi up" makes three ubus calls:
1. ubus call network reload
2. ubus call network.wireless down
3. ubus call network.wireless up
The first and third ubus calls call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel,
so the call sequence becomes,
1. drv_mac80211_setup
2. wireless_device_setup_cancel
3. drv_mac80211_setup
This commit swaps the order of the first two ubus calls,
1. ubus call network.wireless down
2. ubus call network reload
3. ubus call network.wireless up
Consequently drv_mac80211_setup is only called once,
and two related bugs (#FS3784 and #FS3902) are no longer triggered
by /sbin/wifi.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
drv_mac80211_teardown fails silently if the device to be torn down is
not defined. This commit prints an error message.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
When wifi is turned off, drv_mac80211_teardown sometimes fails (silently)
because the device to be torn down is not defined.
This situation arises if drv_mac80211_setup was called twice when
wifi was turned on.
This commit ensures that the device to be torn down is always defined
in drv_mac80211_teardown.
Steps to reproduce:
1) Use /sbin/wifi to turn on wifi.
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
2) Use /sbin/wifi to turn off wifi.
uci set wireless.@wifi-device[0].disabled=1
uci commit
wifi
3) Observe that wifi is still up.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
If drv_mac80211_setup is called twice with the same wifi configuration,
then the second call returns early with error HOSTAPD_START_FAILED.
(wifi works nevertheless, despite the fact that setup is incomplete. But
"ubus call network.wireless status" erroneously reports that radio0 is down.)
The relevant part of drv_mac80211_setup is,
if [ "$no_reload" != "0" ]; then
add_ap=1
ubus wait_for hostapd
local hostapd_res="$(ubus call hostapd config_add "{\"iface\":\"$primary_ap\", \"config\":\"${hostapd_conf_file}\"}")"
ret="$?"
[ "$ret" != 0 -o -z "$hostapd_res" ] && {
wireless_setup_failed HOSTAPD_START_FAILED
return
}
wireless_add_process "$(jsonfilter -s "$hostapd_res" -l 1 -e @.pid)" "/usr/sbin/hostapd" 1 1
fi
This commit sets no_reload = 0 during the second call of drv_mac80211_setup.
It is perhaps worth providing a way to reproduce the situation
where drv_mac80211_setup is called twice.
When /sbin/wifi is used to turn on wifi,
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
/sbin/wifi makes the following ubus calls,
ubus call network reload
ubus call network.wireless down
ubus call network.wireless up
The first and third ubus calls both call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel.
So the call sequence becomes,
drv_mac80211_setup
wireless_device_setup_cancel
drv_mac80211_setup
In contrast, when LuCI is used to turn on wifi only a single call
is made to drv_mac80211_setup.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
The beeper is currently not fully functional and has also
been removed from DTS.
Also remove the dependency for the gpio-beeper module.
Fixes: 695a1cd53c ("ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Remove redundant tags and name things more consistently.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[removed superflous dash]
Signed-off-by: Paul Spooren <mail@aparcar.org>
New swap devices are added in decreasing priority order, starting at -1. Make
sure the zram swap device has the highest priority, by default.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* With kernel 5.4.128, ran: make kernel_menuconfig CONFIG_TARGET=generic
* Manually added back CONFIG_LEDS_TRIGGER_DISK=y so as not to revert
f93fcf8923 ("ipq806x: enable disk-activity LED trigger")
Signed-off-by: John Audia <graysky@archlinux.us>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Though not strictly necessary, add the closing symbol to make the
job easier for future developers editing this file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
sysntpd server becomes unavailable if the index of the bound
interface changes. So let's add an interface trigger to reload sysntpd.
This patch also adds the ability for the sysntpd script to handle
uci interface name from configuration.
Fixes: 4da60500ebd2 ("busybox: sysntpd: option to bind server to iface")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Hardware
--------
MediaTek MT7621 SoC
256M DDR3
16MB BoHong SPI-NOR
MediaTek MT7905+7975 2x2T2R DBDC bgnax / acax
RGB LED
WPS + RESET Button
UART on compute module (silkscreened / 115200n8)
The router itself is just a board with Power / USB / RJ-45 connectors
and DC/DC converters. The SoC and WiFi components are on a
daughterboard which connect using two M.2 connectors.
The compute module has the model number "T-CB1800K-DM2 V02" printed on
it. The main baord has "T-MB5EU V01" printed on it. This information
might be useful, as it's highly likely either of these two will be
reused in similar designs.
The router itself is sold as Tenbay T-MB5EU directly from the OEM as
well as "KuWFI AX1800 Smart WiFi 6 Eouter" on Amazon.de for ~50€ in a
slightly different case.
Installation
------------
A Tool for creating a factory image for the Vendor Web Interface can be
found here: https://github.com/blocktrron/t-mb5eu-v01-factory-creator/
As the OEM Firmware is just a modified LEDE 17.01, you can also access
failsafe mode via UART while the OS boots, by connecting to UART
and pressing "f" when prompted. The Router is reachable at
192.168.1.1 via root without password.
Transfer the OpenWrt sysupgrade image via scp and apply with sysupgrade
using the -n and -F flags.
Alternatively, the board can be flashed by attaching to the UART
console, interrupting the boot process by keeping "0" pressed while
attaching power.
Serve the OpenWrt initramfs using a TFTP server with address
192.168.1.66. Rename the initramfs to ax1800.bin.
Attach your TFTP server to one of the LAN ports. Execute the following
commands.
$ setenv ipaddr 192.168.1.67
$ setenv serverip 192.168.1.66
$ tftpboot 0x84000000 ax1800.bin
$ bootm
Wait for the device to boot. Then transfer the OpenWrt sysupgrade image
to the device using SCP and apply sysupgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds a driver for the AW9523 I2C GPIO expander.
This driver is required to make LEDs as well as buttons on the Tenbay
T-MB5EU-V01 work.
This driver already had several upstream iterations. I'm working to
push this driver to mainline.
Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287
Signed-off-by: David Bauer <mail@david-bauer.net>
58b90461ae elf: Use _dl_catch_error from base namespace in dl-libc.c [BZ #27646]
8c06748c51 Fix use of __pthread_attr_copy in mq_notify (bug 27896)
4b6be914bd Use __pthread_attr_copy in mq_notify (bug 27896)
f4cba6ca1e dlfcn: Failures after dlmopen should not terminate process [BZ #15271]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
It was reported AR8033 did not work in fiber operation mode on the ER-X.
While the earlier attempt of fixing this mitigated the issue of 1000
Base-X link mode not being supported, it also switched to the copper
page, breaking fiber operation altogether.
Extend the hack adding fiber operation so it does not switch to the
copper page. Also remove the part where the supported link mode bit for
1000 Base-X is removed, as this is required for fiber operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
AR8031/AR8033 have different status registers for copper
and fiber operation. However, the extended status register
is the same for both operation modes.
As a result of that, ESTATUS_1000_XFULL is set to 1 even when
operating in copper TP mode.
Remove this mode from the supported link modes, as this driver
currently only supports copper operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit 3628870015.
dnsmasq v2.86test3 has some issues with ubus, so is being reverted.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This reverts commit dea4bae7c2.
dnsmasq v2.86test3 has some issues with ubus and needs reverting, hence
this needs reverting.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Enable the XRX200 PMAC, GSWIP DSA tag and GSIP DSA drivers in the 5.4
kernel config. Update the existing vr9_*.dts{,i} to use the new
Ethernet and switch drivers. Drop the swconfig package from the xrx200
target because swconfig doesn't manage DSA based switches.
The new /etc/config/network format for the DSA driver is not compatible
with the old (swconfig) based one. Show a message during sysupgrade
notifying users about this change and asking them to start with a fresh
config (or forcefully update and then migrate the config manually).
Failsafe mode can now automatically bring up the first lan interface
based on board.json including DSA based setups. Drop
05_set_preinit_iface_lantiq from the xRX200 sub-target as this is not
needed anymore. For now we are keeping it for the ase, xway and
xway_legacy until there's some confirmation that it can be dropped from
there as well.
While here, some boards also receive minor fixups:
- Use LAN1 as LAN1 (according to a photo this port can also be
configured as WAN) on the Buffalo WBMR-300HPD. This makes it easier to
read the port mapping because otherwise we would have LAN{2,3,4} and
WAN (which was the case for the non-DSA version previously).
- vr9_avm_fritz3390.dts: move the "gpio" comment from port 0 and 1 to
their corresponding PHYs
- vr9_tplink_vr200.dtsi: move the "gpio" comment from port 0 to PHY 0
- vr9_tplink_tdw89x0.dtsi: move the "gpio" comment from port 0 to PHY 0
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Tested-by: Notupus <notpp46@googlemail.com> # TD-W9980/DM200/FRITZ 7430
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TDT VR2020
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TP-Link TD-W8980B
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on ZyXEL P-2812HNU-F1
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 7490
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 3490
Tested-by: @jospezial <jospezial@gmx.de> # tested on VGV7510KW22 (o2 Box 6431)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Need this version to add config option for connmark DNS filtering.
Summary of upstream CHANGELOG:
* Handle DHCPREBIND requests in the DHCPv6 server code.
* Fix bug which caused dnsmasq to lose track of processes forked.
* Major rewrite of the DNS server and domain handling code.
* Revise resource handling for number of concurrent DNS queries.
* Improve efficiency of DNSSEC.
* Connection track mark based DNS query filtering.
Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
Manually rebased:
bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
Ensure the esw is initialized before the ethernet device is sending
packets. Further implement carrier detection similar to mt7620.
If any port has a link, the ethernet device will detect a carrier.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
For rt3050 the switch needs to be initialized before the ethernet start sending
packets. Allow switch_init to return -EPROBE_DEFER.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The dts defines the reset fe for all architectures. However
the soc code used direct register access of the reset controller.
Replace the custom soc reset with a generic fe_reset_fe().
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The fe_reset function direct access the reset controller instead
using the reset controller api. In preparation to use the
reset controller.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The zoneinfo packages are not installed per default so neither
/tmp/localtime nor /tmp/TZ is generated.
This patch mostly reverts the previous fix and instead incooperates a
solution suggested by Jo.
Fixes "base-files: fix zoneinfo support " 8af62ed
Signed-off-by: Paul Spooren <mail@aparcar.org>
Instead of assuming /sbin contains the correct BusyBox symlinks, directly invoke
the busybox executable. The required utilities are guaranteed to be present,
since the zram-swap package selects them. Additionally, don't assume busybox
resides in /bin, rely on PATH to find it.
While at it, update the copyright year, use SPDX and switch to AUTORELEASE.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
With the default configuration we generate, the supplicant starts
scanning and tries to connect to any open network when the interface
is enabled.
In some cases it can be desirable to prevent the supplicant from
scanning by itself. For example, if on the same radio an AP is
configured and an unconfigured STA is added (to be configured with
WPS), the AP might not be able to beacon until the STA stops
scanning.
In such a case, the STA configuration can still be required to set
specific settings (e.g. multi_ap_backhaul_sta) so it can't be set to
"disabled" in uci (because that would prevent the supplicant from
being run at all). The alternative is to add the "disabled" parameter
to the default network block in the supplicant configuration.
This patch adds a "default_disabled" setting in UCI which, when set,
adds the "disabled" parameter to the supplicant default network block.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
The system init script currently sets /tmp/localinfo when zoneinfo is
populated. However, zoneinfo has spaces in it whereas the actual files
have _ instead of spaces. This made the if condition never return true.
Example failure when removing the if condition:
/tmp/localtime -> /usr/share/zoneinfo/America/Los Angeles
This file does not exist. America/Los_Angeles does.
Ran through shfmt -w -ci -bn -sr -s
Signed-off-by: Rosen Penev <rosenp@gmail.com>
In the new kernel version 5.X,reboot will fail.
When SOC is reset, flash has not exited the 4-byte address mode,
which causes the operation mode mismatch of flash during boot.Add
broken-flash-reset to make flash exit 4-byte address mode before
SOC reset
Signed-off-by: Liu Yu <f78fk@live.com>
Without this definition ethernet led can work as usual, but it's better to
re-add it. Relying on default values may cause uncontrollable factors.
Fixes: 882a6116d3 ("ramips: improve pinctrl for Youku YK-L1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.
Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617ae)
When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.
So disable the internal switch VLANs by default on these boards.
Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.
In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Define and use some missing macros,
and use them instead of BIT() or numbers for more readable code.
Add comment for a bit change that seems unrelated to ethernet
but is actually needed (PCIe Root Complex mode).
Remove unknown and unused macro RST_CTRL_MCM
(probably from MT7621 / MT7622)
This is the last of a series of fixes, so bump version.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
the register bits for TX delay and RX delay are opposites:
when TX delay bit is set, delay is enabled
when RX delay bit is set, delay is disabled
So, when both bits are unset, it is RX delay
and when both bits are set, it is TX delay
Note: TXID is the default RGMII mode of the SOC
Fixes: 5410a8e295 ("ramips: mt7620: add rgmii delays support")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Add back the register write to disable internal PHYs
as a separate option in the code that can be set using a DTS property.
Set the option to true by default
when an external mt7530 switch is identified.
This makes the driver more in sync with original SDK code
while keeping the lines separated into different options
to accommodate any board with any PHY layout.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
