I do not know if this causes any problems now, but we should not set
it, because it is reserved. Some more recent versions of the Lantiq DSL
API driver and Control is checking if only valid bits are set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48948
There are some cases where ISPs are running ATM over VDSL or PTM over
ADSL, this is not the common case, but these cases exist. Make it
possible to configure OpenWrt for such cases by adding a new config
option line_mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48947
The detailed annex option were only available in the danube DSL app
including the activation of G.992.2 Annex A (ADSL Lite). This is now
also added to the vdsl app for the vrx200.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48946
The adsl control app missed the activation of annex M and annex L in
the Annex A part, this now activates everything the firmware supports.
In Annex L type only the wide US (Mask1) was activated, now also the
narrow US (Mask2) version gets activated.
In addition annex J was also added.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48945
Instead of having two different types adsl and vdsl just create one dsl
type. This way we can use the same luci code for adsl and vdsl and the
config parameters are not so different.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48944
I am not calling dsl_cmd because I want to ignore the lock, quit
should also be send when someone else is accessing it. I saw that some
other call was stuck here and all following calls were stuck in the
dsl_cmd lock.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48943
Instead of having two big binaries only add one binary and then a patch
to create the other one when needed at runtime.
This is easier to handle in one Makefile for both firmware files.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48939
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 48937
Fix buildbot error for mpc85xx.
ehci-fsl.ko should be packaged inside the usb2 package, because it
depends on the ehci kernel module. The fsl-mph-dr-of.ko module can stay
in an own package because the ehci driver depends on it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48932
The function memblock_insert_region() is in the section
__init_memblock, also put crashlog_init_memblock there.
This fixes this section mismatch warning:
The function memblock_insert_region.isra.1() references
the function __meminit crashlog_init_memblock().
This is often because memblock_insert_region.isra.1 lacks a __meminit
annotation or the annotation of crashlog_init_memblock is wrong.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48931
This fixes this section mismatch warning:
The function spi_gpio_custom_get_slave_cs() references
the variable __initdata bus_nump.
This is often because spi_gpio_custom_get_slave_cs lacks a __initdata
annotation or the annotation of bus_nump is wrong.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48930
The buildbots complained about these config options being missing for arm64:
CONFIG_DUMMY_CONSOLE_COLUMNS=80
CONFIG_DUMMY_CONSOLE_ROWS=25
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48929
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48923
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
Ensure that ikey and okey are sent in network byte order to the kernel.
Also don't mangle external IP addrs and routes when reconfiguring iinterfaces.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48919
Apply the error ignore mechanism to host builds as well in order to skip over
broken feed packages.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48918
MD5s are shorter than SHA256, so reading buffer has to be bigger to read the
whole hash.
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
SVN-Revision: 48917
Extend /etc/config/system with a parameter to set the
default respawn retry for procd launched services that
have respawn enabled.
config service
option respawn_retry -1
All services that don't specify specific respawn parameters
will get their defaults added by procd.sh. If respawn_retry
is specified in /etc/config/system the default retry limit
will be set to this value by procd.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 48915
Combine all bus operations for one MMD access in one function.
Protecting all these bus operations with one lock also helps
to avoid potential issues due to bus operations intercepting
the register and data write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48914
The default TTL for address resolution table entries is 5 minutes
for all members of the AR8216 family. This can cause issues if
e.g. Wifi clients roam to another AP and their MAC appears on
another switch port suddenly. Then the client may not be reachable
until the old ARL entry expires.
I would have expected the switch to invalidate old entries if it
detects the same MAC on another port. But that's not the case.
Therefore make the TTL for ARL entries configurable.
The effective TTL will always be a multiple of 7 seconds.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48913
The line before includes the port number anyway so there's no need
to duplicate the port number in the MIB info header.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48912
The decimal values especially for TxByte and RxGoodByte are hard to read
once bigger amounts of data have been transferred.
Therefore complement the decimal values with info in GiB / MiB / KiB.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48911
For unused switch ports all MIB values are zero. Displaying ~40 empty
MIB counters is just confusing and makes it hard to read the output of
swconfig dev <dev> show.
Therefore, if all MIB counters for a port are zero, just display
an info that the MIB counters are empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48910
One of the host patches introduces the new header file lnum_config.h
included by luaconf.h, but doesn't install it.
Install it to allow building C modules for the host Lua.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48907
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48906
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48905
Add a device tree for JCG JHR-N825R
This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. As a special feature, it comes with a two digit seven segment
display that is connected to a pair of daisy-chained 74164 shift
registers that can be controlled via GPIOs.
For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48904
Add a device tree for JCG JHR-N825R
This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48903
Add a device tree for JCG JHR-N805R
This router is based on a RT3050 and has 4MB of SPI flash and 16MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48902
Without the IRQF_ONESHOT flag in devm_request_threaded_irq() call I get
following error:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 56
gpio-keys gpio-keys: failed to request irq:56 for gpio:20
>From kernel/irq/manage.c:
The interrupt was requested with handler = NULL, so we use the default
primary handler for it. But it does not have the oneshot flag set. In
combination with level interrupts this is deadly, because the default
primary handler just wakes the thread, then the irq lines is reenabled,
but the device still has the level irq asserted. Rinse and repeat....
While this works for edge type interrupts, we play it safe and reject
unconditionally because we can't say for sure which type this interrupt
really has. The type flags are unreliable as the underlying chip
implementation can override them.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 48894
